Patrol Base.
0 Items | Total £0.00View Basket
  • Visit Our Store.
  • Fast UK Delivery.
  • Airsoft Two Tone Service
  • Airsoft Upgrades and Repairs

  • Airsoft Switches, Selectors, & Mosfets

  • Sort by

    Switch

Displaying: 1 to 11 of 11
Viewing page: 1 
  • ACM
  • Airsoft Systems
  • APS
  • Ares
  • ASG
  • ASPUK
  • Classic Army
  • CYMA
  • G&G Armament
  • Gate
  • Guarder
  • Keen Sharp
  • Laylax
  • Patrol Base
  • RetroArms
  • TIPPMANN
  • Well
gate-Nanohard-3rd-gen-multifunction-aeg-controller

Gate NanoHARD 3rd Gen Multifunction AEG Controller

  • AEG Controller
  • Huge Improvements
  • AEG Protection

GATE - NanoHARD 3rd Gen Multifunction AEG Controller is a Generation 3 Micro Computer Controller Chip Set designed to add a huge variety of functionality to Airsoft AEG. The chip is built to be as compact as possible, requiring the smallest amount space possible, and is specially coated to the Military Specification (Mil-Spec) MIL-V-173C. The chip provides active breaking, which stops the motor from over spinning, which can be turned on and off to the users requirements. The chipset also features a Smart Fuse, which is their latest and most reliable fuse they have made to date, featuring a true current sensor. With a combination of current, voltage and temperature measurements the fuse protects your rifle from a variety of problems, such as: Overheating, Overloading, Short Circuiting, and protects the Motor and Battery against damage from Jamming. The in-built MOSFET is designed to achieve a higher rate of fire and trigger response, as well as protects the mechanical trigger contacts by directly bypassing the contacts and going straight to the motor. The chip set also provides protection against the over-discharge of LiPo battery, and once activated with prevent them from dropping below their nominal usage levels by constantly monitoring the voltage then stopping the weapon from firing when the power is too low. The system also provides protection from contact bounce, providing a higher ROF, a better trigger response and making the unit less prone to heating. This LiPo can be used at a minimum of 3v, and up to 17v, making it ready for 14.8v LiPo Batteries. The body of the unit is coated to the Mil-Spec variation MIL-V-173c, making it resistant to atmospheric conditions. The package comes with everything you need to connect up the unit, with spare wires for different trigger setups, as well as jumpers and configuration button. This is perfect for those Airsoft Players who want the absolute best out of their weapon, adding a multitude of features which improve game pl

£29.99

£34.99

gate-merf-3-2-3rd-gen-advanced-mosfet-unit

Gate MERF 3.2 3rd Gen Advanced Mosfet Unit

  • Plug & Play / Installed
  • 3rnd Burst and ROF Adjuster
  • Programmable Smart Trigger

GATE - MERF 3.2 3rd Gen Advanced Mosfet Unit is a Generation 3 Micro Computer Programmable Controller Chip Set designed to add a huge variety of functionality to Airsoft AEG. The chip is built to be as compact as possible, requiring the smallest amount space possible, and is specially coated to the Military Specification (Mil-Spec) MIL-V-173C. The chip provides active breaking, which stops the motor from over spinning. The in-built MOSFET is designed to achieve a higher rate of fire and trigger response, as well as protects the mechanical trigger contacts by directly bypassing the contacts and going straight to the motor. The chip set also provides protection against the over-discharge of LiPo battery, and once activated with prevent them from dropping below their nominal usage levels by constantly monitoring the voltage then stopping the weapon from firing when the power is too low. The system also provides protection from contact bounce, providing a higher ROF, a better trigger response and making the unit less prone to heating. This LiPo can has a working range of 3v to 15v, making it ready for 11.1v LiPo Batteries. The body of the unit is coated to the Mil-Spec variation MIL-V-173c, making it resistant to atmospheric conditions. The package comes with everything you need to connect up the unit, with spare wires for different trigger setups and even Deans Connectors. This is perfect for those Airsoft Players who want the absolute best out of their weapon, adding a multitude of features which improve game play and performance.

£39.99

£44.99

GATE Electronics - TITAN Drop In MOSFET V2 Module - Rear Wired

Gate TITAN Drop In MOSFET V2 Module - Rear Wired

  • Highly Advanced System
  • Drop-In Kit and Parts
  • Trigger Replacement

GATE Electronics - TITAN Drop In MOSFET V2 Module - Rear Wired is a drop in MOSFET Kit designed for Version 2 Gearbox, which are typically seen in M4 Variant Rifles. The Titan is a complete trigger set replacement, with optical sensors instead of mechanical switches and has a high end software and sensor based sector gear detection, allowing some of the fastest and most efficient AEG builds. The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries and is compatible with most V2 Gearbox on the market with no modification. The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical ,and has Eight Onboard Optical Sensors. The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and breaking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. Once installed the MOSFET can be re-programmed via the Gate Configuration Card or via the USB-Link to a Windows based PC, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. Whats important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well theyve been implemented. For more information on this Gate MOSFET, please see the extensive list of features in the Features Section. Should you need any help installing the MOSFET please f

£75.00

GATE Electronics - TITAN Drop In MOSFET V2 Module - Front Wired

Gate TITAN Drop In MOSFET V2 Module - Front Wired

  • Highly Advanced System
  • Drop-In Kit and Parts
  • Trigger Replacement

GATE Electronics - TITAN Drop In MOSFET V2 Module - Front Wired is a drop in MOSFET Kit designed for Version 2 Gearbox, which are typically seen in M4 Variant Rifles. The Titan is a complete trigger set replacement, with optical sensors instead of mechanical switches and has a high end software and sensor based sector gear detection, allowing some of the fastest and most efficient AEG builds. The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries and is compatible with most V2 Gearbox on the market with no modification. The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical ,and has Eight Onboard Optical Sensors. The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and breaking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. Once installed the MOSFET can be re-programmed via the Gate Configuration Card or via the USB-Link to a Windows based PC, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. Whats important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well theyve been implemented. For more information on this Gate MOSFET, please see the extensive list of features in the Features Section. Should you need any help installing the MOSFET please

£75.00

GATE Electronics - TITAN Drop In MOSFET V2 Complete Set - Rear Wired

Gate TITAN Drop In MOSFET V2 Complete Set - Rear Wired

  • Highly Advanced System
  • Complete TITAN Kit
  • Trigger Replacement

GATE Electronics - TITAN Drop In MOSFET V2 Complete Set - Rear Wired is a drop in MOSFET Kit designed for Version 2 Gearbox, which are typically seen in M4 Variant Rifles. This variation of the Kit comes with the MOSFET Unit, the Programmable Pad, and the USB-Link. The Titan is a complete trigger set replacement, with optical sensors instead of mechanical switches and has a high end software and sensor based sector gear detection, allowing some of the fastest and most efficient AEG builds. The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries and is compatible with most V2 Gearbox on the market with no modification. The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical ,and has Eight Onboard Optical Sensors. The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and breaking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. Once installed the MOSFET can be re-programmed via the Gate Configuration Card or via the USB-Link to a Windows based PC, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. Whats important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well theyve been implemented. For more information on this Gate MOSFET, please see the extensi

£110.00

GATE Electronics - TITAN Drop In MOSFET V2 Complete Set - Rear Wired

Gate TITAN Drop In MOSFET V2 Complete Set - Front Wired

  • Highly Advanced System
  • Complete TITAN Kit
  • Trigger Replacement

GATE Electronics - TITAN Drop In MOSFET V2 Complete Set - Front Wired is a drop in MOSFET Kit designed for Version 2 Gearbox, which are typically seen in M4 Variant Rifles. This variation of the Kit comes with the MOSFET Unit, the Programmable Pad, and the USB-Link. The Titan is a complete trigger set replacement, with optical sensors instead of mechanical switches and has a high end software and sensor based sector gear detection, allowing some of the fastest and most efficient AEG builds. The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries and is compatible with most V2 Gearbox on the market with no modification. The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical ,and has Eight Onboard Optical Sensors. The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and breaking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. Once installed the MOSFET can be re-programmed via the Gate Configuration Card or via the USB-Link to a Windows based PC, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. Whats important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well theyve been implemented. For more information on this Gate MOSFET, please see the extens

£110.00

 A range of Airsoft internal electronics from trigger sets to mosfets and wiring. All suitable for a range of Airsoft AEGs supplied by a range of brands including Classic Army, G&G, Tokyo Marui and many more.

 

Need Help? Call a specialist on 01484 644709

Monday to Saturday 9:30am to 5:30pm, but don't forget our late night Thursdays 9:00pm closing!

Exclusive offers, news & events

  • SagePay
  • PayPal
  • Visa
  • MasterCard
  • Maestro
  • Solo
  • Delta
  • Visa Electron
  • Verified by Visa
  • MasterCard SecureCard
  • Norton Secured