Customers who bought this item also bought
Program your EFCS AMOEBA Airsoft RIF in less than 10 seconds into a variety of firing modes. As well as setting the firing mode for your AEG, you can also set the type of battery you use. Designed to protect your circuits but give a more fun firing experience with a very fast and easy setup. Firing modes include, safe, semi and auto or safe, semi 3 round burst, safe semi 3rnd burst and auto or safe and semi only
G&G - ETU Electronic Trigger Unit, an highly affordable replacement trigger unit, wiring and MOSFET for anyone looking to run an 11v LiPo in their Airsoft V2 gearbox AEG. This kit includes all the parts needed for a full installation. Please note, you may have to slightly modify your gearbox casing depending on the brand. Please read the special instructions and "Features" bullet points for more information on this area. The G&G ETU completely replaces all electronics internally. Achieve near instant trigger response, deter carbon build up and unlock a 3 round burst option within seconds of installation. We recommend you have some internal parts knowledge before installing this item. Incorrect installation can break other components as well as the ETU.
ASG - 10x Ultimate Motor Connector Plugs - Gold, if you have a damaged wire, snapped motor connector or just want to improve your electric conductivity then this pack is ideal. You get 10 connectors in total with 5 sections of Red and 5 sections of Black heat shrink to tidy up the job. You do not need to solder your wires onto the connectors but we advise you do for the best conductivity and connection quality. The Gold connectors will have to be bent into shape once you have soldered on your wires. Please be careful we they can only be bent once or twice. The more you bend them in and out of shape the weaker they will become, just like any connector. Ensure you have a tight fit to your motor by using some pliers just to nip things up a little. This prevents any connectors falling off during an important fire fight or RC race / flight.
Keen Sharp - Silver Wiring - 2m, highly rated by Airsoft gun techs due to it's ease of use. You can bend this wiring to the shape of your gearbox preventing if from popping out during assembly. This silver wiring is very conductive due to its metal properties, as a result and when combined with the right components you will notice improved trigger response and electrical efficiency. The stiffer than normal insulated coating allows you to bend/shape the wiring into the tightest of grooves. This works great with aftermarket/custom MOSFET too.
GATE - PicoSSR 3 AEG Micro Mosfet Unit is an ultra compact Generation 3 MOSFET built to be as compact as possible, requiring the smallest amount space possible, and is water resistant. This MOSFET is designed to achieve a higher rate of fire and trigger response, as well as protects the mechanical trigger contacts by directly bypassing the contacts and going straight to the motor. The unit itself is so compact that it can be fit in any Airsoft AEG, allowing you to wire the unit in down buffer tubes and in tight hand guards. The package comes with everything you need to connect up the unit, with spare wires for different trigger setups. This is perfect for those Airsoft Players who want the absolute best out of their weapon, adding a features which improve the performance of Rifles.
ARES - Amoeba EFCS ECU Gearbox Complete - Rear Wired is a complete gearbox replacement for Amoeba / M4-E Airsoft weapons. The unit itself is the reprogrammable EFCS unit, allowing it to be programmed for three round burst or be locked to single shot using the EFCS programming unit. The MOSFET on the gearbox is the new generation 'Blue MOSFET' which is more resistant to Ampage / Voltage fluctuations and spikes, and allows 11V LiPo and LiFe type batteries as standard. The gearbox is of the highest build quality, coming with a quick release spring guide, silver wiring, electronic trigger and upgraded MOSFET. This is the perfect gearbox for if you want to start upgrading your pre-existing Amoeba or EFCS or want to switch a front wired gun to a rear wired system with no hassle.
GATE - NanoASR 3rd Gen Advanced Solid State Relay Mosfet is a Generation 3 Micro Computer Controller Chip Set designed to add a huge variety of functionality to Airsoft AEG. The chip is built to be as compact as possible, requiring the smallest amount space possible, and is specially coated to the Military Specification (Mil-Spec) MIL-V-173C. The in-built MOSFET is designed to achieve a higher rate of fire and trigger response, as well as protects the mechanical trigger contacts by directly bypassing the contacts and going straight to the motor. The system also provides protection from contact bounce, providing a higher ROF, a better trigger response and making the unit less prone to heating. This LiPo can has a working range of 3v to 17v, making it ready for 14.8v LiPo Batteries. The body of the unit is coated to the Mil-Spec variation MIL-V-173c, making it resistant to atmospheric conditions. The package comes with everything you need to connect up the unit, with spare wires for different trigger setups. This is perfect for those Airsoft Players who want the absolute best out of their weapon, adding a multitude of features which improve game play and performance.
ASG - Ultimate Version 2 Trigger Switch Unit is a replacement unit for Trigger Contacts, usable in Version 2 / V2 Airsoft AEG Gearbox. This unit is the perfect replacement for any worn or burnt out trigger mechs you have in your current Airsoft AEG. The most common problem people have with Trigger Contacts is Burnt Out Triggers, due to electricity Arcing between the contacts, and this is a direct replacement. This is the perfect purchase for any Airsoft Skirmisher with an M4/15/16 Style or other V2 Gearbox Type weapon, who like to have spares or repairs for the day before a Skirmish.
Need Help? Call a specialist on 01484 644709
Monday to Saturday 9:30am to 5:30pm, but don't forget our late night Thursdays 9:00pm closing!