Airsoft Attachment & Accessory Discounts

If you've had a cut-off lever failure or you like to keep parts on hand just in case the worst happens, the G&G Armament Cut Off Lever For V2 Gearbox is perfect. This is a replacement original part constructed from alloy, compatible with most version 2 gearboxes on the market.

The cut-off lever is a piece that sits between your trigger and sector gear and serves to interrupt or disconnect the trigger once your gearbox has made a complete cycle, very useful!

If you need a battery for a fixed stock or other large battery compartments this one should fit the bill! The 7.4V 1800mAh 20C Block LiPo Battery from Electro River is the perfect battery for full stocks found on M16, AK, SMG-5 and G3 Airsoft AEGs. The battery measures 10 x 1.2 x 3.5cm approximately with a wire length of around 9cm and is pre-wired to a mini-Tamiya battery connector.

The battery is a 7.4V 2-cell battery in block configuration with a continuous discharge rate of 20C and a maximum discharge rate of 40C, making it great for almost any Airsoft AEG, though make sure you measure before ordering!

Those of you looking for a battery with a truly large capacity, you've come to the right place! The battery is perfect for larger battery compartments such as SMG-5, G3, M16 and AK platforms with fixed stock battery compartments. The battery has a voltage of 7.4v, a capacity of 2800mAh and a continuous discharge rate of 25C with a maximum discharge rate of 50C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.

The battery measures 13x1.1x4.2cm with a cable length of roughly 10cm.

If you have worn out your AEGs trigger or you want the mil-spec look to replace your current trigger, this is perfect for you! The G&G Armament Trigger For V2 Gearbox is constructed from alloy with a textured finish and is patterned after the standard curved "Milspec" trigger found on the M4A1 rifle, MK18 MOD.0 and MOD.1, along with most other M4/AR-15 rifles used in military service in the real world.

The trigger is compatible with version 2 gearboxes which are found in the vast majority of M4/AR-15 AEGs. This means that the G&G Armament Trigger For V2 Gearbox trigger should work in practically any M4/AR-15 AEG but will require the gearbox to be opened for installation.

A replacement side mount plate for CMYA AK47/74 series Airsoft AEG weapons, which when fitted allows users to install AK style side-mounted scope mounts.

Next level of Airsoft sniper rifle hop-up rubber produced with similar materials and processes to Madbull's current line up of AEG hop-up components.

A replacement original KRYTAC part which fits version 2, 3, 6 and 7 gearboxes. This cylinder is a Type 1, meaning it has a port in the side intended to reduce the air volume for use on short barrelled platforms (<363mm inner barrel) and prevent the "suck back" phenomenon.

An 11.1v 2000mAh Li-Ion battery for Airsoft Electric Guns, which comes supplied in a Crane/Butterfly/Saddle configuration, meaning two rows of cells. This makes them very easy to place in awkard-to-fit spots such as Handguards and Crane Stocks, and will provide better Power Density that traditional LiPo batteries.

A Full Polymer constructed Mid-Cap Magazine for the G&G branded G36 series AEGs. Perfect for those who want to inject more realism into their play-style.

A spare magazine for the Gas Blowback submachine gun; the WE SMG-8, and the WE SMG-A1 (Also known as the New Wave - NP7 or "Small Rice 7").

*Please note that this magazine is not compatible with the Tokyo Marui SMG-7 or Umarex MP7 platforms

For those in the market for a suppressor for their AAP-01 Assassin GBB pistol, or for that matter any pistol requiring a slim style suppressor, consider the DDW Suppressor from Action Army. This suppressor attaches to any 14mm CCW male thread and is a lightweight aluminium design with attractive vents and a foam filling for some suppression effect.

Ideal for reviving worn out RIFs or as a backup for a rainy day, this is a complete and assembled gearbox including motor, that is ready to drop into any compatible Version 2 accepting replica.

A drop-in trigger, ETU & MOSFET for Version 2 compatible rear-wired Airsoft replicas, which includes features like a programmable trigger, low battery cutoff, shot sensor and comes included with a vertical 'speed trigger'.

The WADSN DBAL Mini is a compact laser aiming module with two fully adjustable lasers combined into a single unit! The DBAL-Mini from WADSN provides both a red visible laser and an IR laser which is only visible under night vision, both of which are zeroed together with common tool-less adjustment dials. This DBAL-Mini is the much sought after aluminium version and boasts more realistic construction than its polymer counterparts. If you own night vision of any kind, this laser is a must!

This is an Aluminium constructed Muzzle Device that is designed for AK Platform replicas, but will fit and work with any Airsoft Gun that has a 14mm CCW Threaded [Male] Outer Barrel, which is 95% of replicas.

A 530 round high capacity, wheel-wound magazine, designed for use with G&G's UMG SMG electric replica. Constructed from durable, high strength and lightweight polymers.

The Angry Gun QDC 3-Prong Flash Hider matches the design of real steel flash hiders such as the ones found on AUGs. It is constructed from steel making it extremely durable and sure to withstand any skirmish. This muzzle device is designed to work with other Angry Gun QDC attachments such as their suppressor and tracer unit. These products interlock seamlessly guaranteeing a reliable attachment every time.

This flash hider mounts to 14mm CCW threading, commonly found on most Airsoft assault rifles. It also has a grub screw so you can ensure it is securely attached to your replica with no worries about it coming off. The flash hider also comes with a stainless steel shim, to make sure that it is situated perfectly on your rifle's outer barrel.

If you want a super realistic flash hider that is compatible with Angry Gun QDC suppressors and tracers, this is the one for you! Its steel construction and real steel design certify that this flash hider is perfect for any skirmisher seeking a realistic loadout.

The STTI B9/B92 Conversion Kit is a Polymer constructed Body Kit for... you guessed it, B9 and B92 Airsoft Gas Blowback Pistols. This awesome kit will convert your lowly Airsoft Pistol into a functional Carbine with Sliding Stock, 20mm Rail System, Ambidextrous Charging Handle as well as plenty of room for a Suppressor, Inner Barrel Extension or Tracer Unit!

This is one for the AK lovers! The Russian Firearm Fanatics and the Weekend Gopnik Operators, here to complete the tactical aesthetic of your AK is the 5KU PT-3 Telescopic Stock, featuring a full alloy construction and a rubber butt pad, this replica PT-3 Classica stock is a fine addition to your Eastern Operator loadout.

An efficient and well-constructed Air Nozzle which is available for a wide range of replicas, and ensures improved durability and smooth operation.

A 14mm CCW threaded muzzle device, designed to replace your Airsoft guns original flash hider with a sound amplifying compensator. This flash hider is an great to match an aggressive playstyle to a combat CQB primary.

A green gas magazine designed for the ICS BLE-XFG range of pistols. Holds up to 19 rounds

A  Full polymer constructed High Cap Magazine for the G&G branded G36 series AEGs. Perfect for those who want to spends more time shooting rather than reloading.

This spare magazine for the G&G Armament Piranha gas blowback Airsoft pistol is constructed with a transparent polymer shell with mock 9x19mm cartridges visible within, and is a great way to make your pistol stand out on the field. It is filled with BBs using a speedloader, preferably with a GBB adapter, and can be filled with gas using the fill valve on the baseplate. If you own a G&G Piranha Pistol, then Spare Magazines are an absolute must for staying in the field longer and avoiding the long walk back to the safe zone to reload!

Looking for some extra firepower for your TM NGRS AEG? The NUPROL 1200rnd Electric drum magazine is the key to gaining the volume of fire advantage when skirmishing, and is the perfect tool to repel an ambush. This drum magazine is constructed from high-density polymer with a modern design aesthetic, and is the first of its kind for the NGRS system! If the "normal" AEG users are getting on your nerves with their high-caps, pull this bad boy out of the kitbag to remind them who is the boss!

Please note, this drum magazine is NOT compatible with standard M4/AR-15 AEGs and only works with Tokyo Marui NGRS (Next Generation Recoil Shock) AEGs.

A 6mm BB Airsoft magazine, designed for use with Tokyo Marui's SMG-7 AEP electric Airsoft Submachine gun, featuring a medium capacity of 50 rounds. 

A spare or replacement 50rnd short magazine for the Krytac Kriss Vector, which is made to a high standard with excellent quality Polymers, and features the KRISS trademark as well as faux round count.

A series of Selector Plates from Modify, which are available for a range of AEGs.

A dual-bay Battery Charger for the RunCam Scope Cam 4K, allowing you to charge up to two Batteries simultaneously. Whilst the RunCam Scope Cam is amazing and compact, it's Battery Life is limited, and so will be the deciding factor in how much footage you can capture throughout a day. Provided you have enough Batteries on standby, you can record for as long as you like, making this an essential purchase for any serious Airsoft content creator.

Calling all master builders! Now you can customise to your hearts content using your favourite brick system. With LayLax Block interfaced parts, you can bring the modularity of your gun to new levels, whether it be pirate themed, castle themed, space themed or whatever your favourite set was from your childhood.

This variant fits to Picatinny rail systems, locking with a grub screw on the top. These are much like standard rail covers, only this time they're a lot more jazzy and colourful and the cinematic adaptation is voiced by Chris Pratt.