All Airsoft Batteries

A LiPo Crane Stock battery designed to fit in stocks and small spaces which other large batteries do not fit. The battery is also know as a Nunchuck battery, with the cells connected via the wires allowing them to be placed down the side of barrels or in an M4 Crane Stock.

A Standard powered Airsoft Battery, designed to be used in almost all Airsoft AEG weapons with a mini-Tamiya connector, providing the perfect amount of power for most Airsoft Weapons. 

A battery designed and built by NUPROL specifically for Airsoft Skirmishers as part of their POWER range of Batteries, the battery is constructed from individual cells which are held together by durable shrink wrapping, and feature a mini-Tamiya connector to connect it to your weapon.

The VP Racing 8.4v 1600mAh crane stock battery is a highly popular NiMH battery that is identical to most free batteries included with Airsoft weapons.

VP Racing are well known for their high quality and high performance batteries with this one being a crane form factor. The battery has a voltage of 7.4v, has a capacity of 1450mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery consists of two cells working in tandem, with each cell measuring 13x0.7x2cm each with a cable length of roughly 7.5cm of wire. The battery should fit in crane stock battery compartments such as M4s and some handguards and full stocks, but remember to measure up before hand!

A Battery designed to fit into most Crane Stocks, this is a 7 cell Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers as part of their POWER range of Batteries. 

If you need slim 7.4V crane stock LiPo for your crane stock or handguard battery compartment, the VP Racing 7.4V 1000mAh 20c LiPo Crane Stock Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and is comprised of 2 cells, each of which measures 11 x 1.5 x 0.5 cm. The wire length between the cells and connector is approximately 10cm, giving you a bit of flexibility to ensure the battery is installed properly. As always, we recommend measuring thoroughly to ensure it fits before ordering!

An Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries. 

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. Fitted with a deans connector for low resistance.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards  and comes fitted with Deans connectors instead of the standard Tamiya for upgraded Airsoft Guns.

A super thin, triple cell crane stock styled 11.1v LiPo battery, featuring a small Tamiya connector for easy use.

A super thin triple crane stock 11.1v 1300mAh 25C LiPo, which features a Deans Connector instead of the standard Mini Tamiya. 

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

A triple crane stock 11.1v 1450mAh 25C LiPo, which features a Deans connector instead of the standard small Tamiya.

An ultra thin and lightweight crane stock battery, perfect for squeezing into the ever more popular Airsoft crane stock.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. 

A LiPo crane stock battery designed to fit in stocks and small spaces which other large batteries do not fit.

An 11.1v crane stock LiPo Battery with an impressive 2600mAh capacity, designed to ensure that your Airsoft AEG can survive a whole day of Skirmishing.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

For those of you with some serious power requirements. This large LiPo battery is designed for crane stock use but may also be suitable for larger Airsoft hand guards too. This variant of the battery is fitted with a Deans connector.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

An Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries.

This LiPo battery from Gens Ace is designed to fit into flat and long battery compartments, such as those found inside the handguards of an AR36 or SMG-5. The battery connects to your AEG via a mini-Tamiya connector and provides 1300mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

A LiPo saddle battery designed to fit in handguards in replacement of the traditional 1600mAh NiMH blocks/saddles (G36 handguards etc).

A crane stock Lithium Polymer (LiPo) type battery, which allows for the best possible power to size ratio and charge life available in a compact battery.

A humungous 7.4v LiPo battery in a Crane Stock / Nunchuck configuration which offers a massive 3000mAh capacity. If you want the biggest battery you can possibly squeeze into your replica, this is probably it!

An 11.1v 2000mAh Li-Ion battery for Airsoft Electric Guns, which comes supplied in a Crane/Butterfly/Saddle configuration, meaning two rows of cells. This makes them very easy to place in awkard-to-fit spots such as Handguards and Crane Stocks, and will provide better Power Density that traditional LiPo batteries.

If you need a compact Airsoft battery which fits almost anywhere the 7.4v 1100mAh 20C LiPo Crane Battery from VAPEX is ideal. This battery is pre-wired with a mini-Tamiya battery connector and each cell unit measures 11 x 0.7 x 2.2 cm with approximately 9 cm of wiring between each cell and the connector, making it great for tight spaces and use with multiple different platforms.

The compact size of this crane/nunchuck battery makes it ideal not only for Airsoft but also for electronics hobby applications and R/C when a lightweight and compact power source is a priority. Whether it needs to fit into a buffer tube, crane stock, handguard or practically anywhere else this super slim battery is perfect, especially if you want a single battery which fits in multiple guns!

If you need an Airsoft battery that fits in almost anything and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo/ LiFe/NiMH Balance Charger, a Safe Charging Bag and an ASG 7.4V 1300mAh LiPo Battery in Crane configuration with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs and capable of fitting inside Crane stocks, fixed stocks and most handguards! If you have multiple different AEGs and you want a battery to fit them all, chances are this one will! 

The dimensions of the included battery are as follows: 10.1cm x 0.7cm x 2cm per cell group (2x cell groups on each battery) with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Crane Stock, M4/AR-15, SMG-5 & AK Fixed stock, AR-36 & SMG-5 handguards, Tokyo Marui SCAR-L/H NGRS stock, most M4/AR-15 buffer tubes. 

This LiPo battery from Gens Ace is designed to fit into flat and long battery compartments, such as those found inside the handguards of an AR36 or SMG-5. The battery connects to your AEG via a Deans connector (aka a T-Plug) and provides 1300mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.