Airsoft Pistol Magazines

If you're planning to run your EU series, AAP-01 or Lancer Tactical CTHULHU on HPA, the Lancer Tactical HPA Adapter for M4/AR-15 AEG Magazines; EU Series & AAP-01 will do the trick! This HPA adapter is designed for EU series GBB pistols and should also fit the Action Army AAP-01 and Lancer Tactical's radical CTHULHU pistol. Designed to allow standard M4/AR-15 AEG mags to be used along with a High Pressure Air (HPA) power source, you can kiss goodbye to the "cooldown" effect and limited magazine capacity with this adapter on your gat!

The set includes both an EU and US HPA connector but you will need an airline, HPA bottle and regulator to run this adapter. The advantages of using HPA when performance is concerned include the elimination of FPS fluctuation due to the "cooldown" effect, resulting in improved shot-to-shot consistency and improved accuracy down range, especially under rapid fire. If you're taking your playstyle in a speedy direction, this adapter will change your game!

A 34rnd spare magazine for the CYMA CM.128 Hi-Capa styled Airsoft Electric Pistol, which will work with other CYMA AEPs but will extend beyond the baseplate depending on the model. It is filled from the top using a Speedloader to push BBs past the feed lips.

If you're planning to run your Tokyo Marui Hi-Capa GBB on HPA, the Lancer Tactical HPA Adapter for M4/AR-15 AEG Magazines; TM Hi-Capa GBB will improve your firepower considerably!

This HPA adapter is designed for the Tokyo Marui Hi-Capa GBB series and may fit Hi-Capa clones based on the TM design, though we can't make any guarantees. Allowing standard M4/AR-15 AEG mags to be used along with a High Pressure Air (HPA) power source, you can kiss goodbye to the "cooldown" effect and limited magazine capacity if you're rocking this on your 'Capa!

The set includes both an EU and US HPA connector but you will need an airline, HPA bottle and regulator to run this adapter. The advantages of using HPA when performance is concerned include the elimination of FPS fluctuation due to the "cooldown" effect, resulting in improved shot-to-shot consistency and improved accuracy down range, especially under rapid fire. If you're taking your playstyle in a speedy direction, this adapter will change your game!

A spare or replacement Gas Magazine for the Cyber Gun FN Five Seven (5-7), which holds a total of 17 rounds and is constructed to the exact same standard as the original magazine, using Alloy for the body and Polymer for the feed lips.

If you need spare magazines for your Specna Arms or EMG Salient Arms BLU and you want to keep your pistol pure with the exact mags for the platform these are what you need! These magazines are manufactured by Armourer Works and licenced by Salient Arms through EMG and come with a Salient Arms extended baseplate to complete the SAI look. This is effectively an EU series magazine, but the included baseplate features the S in a cube logo and SAI in recessed detail on the bottom to complete the Salient Arms look.

The magazine can be filled through the fill valve on the baseplate with the magazine held inverted, and BBs can be loaded in through the feed lips at the top, or by pulling the follower down and loading through the widened section of the channel on the front, depending on your preference. Obviously, standard EU series magazines from WE and Armourer Works will fit and feed in the Specna and EMG BLU GBB pistols, but what is the point of going for a stylish Salient Arms pistol without the proper magazines?

A gas blowback Airsoft CO2 magazine developed by VORSK for their VX-9 and MEU range of pistols, constructed with an Alloy Body and Polymer base plate. The magazine is an extended version of the standard magazine and holds an impressive 36 rounds and is a direct replacement for the magazine which comes with the pistol, filled with BBs from the top or front, and CO2 bulbs can be installed through the side of the shell and tightened using the included allen key, through the baseplate.

If you're looking to bolster your VORSK VX-9 or MEU pistol with 100% compatible magazines then this is the way to go. This magazine is also great for those Airsoft skirmishers who believe in accuracy through volume, or CQB players who want to just run around with a spare mag in their hand and go shoot. Particularly useful for the winter months, using CO2 should reduce the effect of cooldown on your pistol!

A gas blowback Airsoft CO2 magazine developed by VORSK for their VX-9 and MEU range of pistols, constructed with an Alloy Body and Polymer base plate. The magazine is an extended version of the standard magazine and holds an impressive 36 rounds and is a direct replacement for the magazine which comes with the pistol, filled with BBs from the top or front, and CO2 bulbs can be installed through the side of the shell and tightened using the included allen key, through the baseplate.

If you're looking to bolster your VORSK VX-9 or MEU pistol with 100% compatible magazines then this is the way to go. This magazine is also great for those Airsoft skirmishers who believe in accuracy through volume, or CQB players who want to just run around with a spare mag in their hand and go shoot. Particularly useful for the winter months, using CO2 should reduce the effect of cooldown on your pistol!

If you desire to dump 350 BBs without the added effort of swapping magazines but don't want to mess with a HPA setup then this is your chance! This WE 350rnd Green Gas Drum Magazine is designed for WE 1911 pistols but may work with others, though compatibility cannot be guaranteed.

The magazine is constructed with a hefty alloy gas reservoir with a high-density polymer drum with rubber shock bumpers and an external winding wheel on the front which is easy to wind quickly with or without gloves. The sizeable gas reservoir of this magazine means in most cases you will easily be able to dump the full magazine without a refill, so if you want to run a pistol only this will provide you with more than enough firepower!

They've only gone and done it, the absolute lunatics! A drum magazine for G&G GTP9 and SMC9. Clearly G&G have been listening to the community and have brought us this 300 round wheel wound drum mag resulting in some insane firepower for your now portable LMG in pistol form factor!

If you have yourself one of the cutest backup pistols around, the Cyber Gun Colt Junior, you may want a spare mag to give you an even better chance in those last-ditch scenarios! The 7 rnd Colt Junior GBB Magazine from Cyber Gun is similarly laid out to a standard GBB magazine but miniaturised. The magazine can be loaded through the feed lips at the front, and the gas fill valve can be found on the magazine base plate. The left side of the magazine features a pull-down follower, making it easy to load BBs even without a speed loader.

A chrome-effect gas magazine for the WE XDM Compact 3.8, which can hold up to 17 rounds.

An Alloy constructed spare (or replacement) Magazine for the KWC Non-Blowback PM CO2 Makarov Pistol, which takes standard 12g CO2 Bulbs from the side and is filled with 13 x BBs either by hand or with a Speedloader. If you own a KWC PM CO2 Makarov and want to spend longer in the field playing, and less time in the safe zone reloading, then you need to stock up on spare Magazines.

A gas blowback magazine designed for the WE Europe EU-Series compact pistol range, and is designed to fit the EU26, EU27, and the EU33 Advance with the grip extension removed. The magazine is constructed from Alloy, with a Polymer base plate, feed lips and follower, and comes fitted with a unique curved base plate.

If you want to keep your beast of a Novritsch pistol shooting perfectly in cold weather, you'll need one of these! The Novritsch 31rnd CO2 Magazine for SSP1/SSP5 GBB Pistol is constructed from alloy with a polymer baseplate and is compatible with both the SSP1 and SSP5 GBB pistols.

The mag is loaded either through the feed lips or the follower channel when the follower is held down using a speed loader or loading tool. If you're new to CO2, we recommend giving our CO2 guide a quick read so you can stay abreast of maintenance and CO2-specific safety issues.

This mag uses 12g unthreaded CO2 capsules, one of which needs to be installed inside the magazine shell. To access the CO2 compartment, simply press the small button on the bottom and slide the baseplate off. Underneath, you will find the CO2 plug which can be removed with the included Allen key or a flat tool if you don't have the Allen key handy. Install your CO2 capsule inside, tighten the plug down until you hear the capsule pierce and replace the baseplate; you are now good to go!

If you want to keep your B9 pistol running when the cold sets in a CO2 mag is the only way to do it. The WE 25rnd CO2 Magazine For B9/92 is constructed from alloy with polymer feed lips, a brass knocker valve and rubber gas route bucking. This CO2 mag is designed for the WE B9 and B92 pistols and will not work in other versions. The magazine can be loaded through the feed lips at the top of the design and due to the lack of an external follower, a speedloader with a GBB adapter is recommended for ease of loading. 

The CO2 compartment is inside the shell and accessible with the baseplate removed. To achieve this, simply pull upwards on the polymer tab at the bottom of the follower channel and slide the baseplate forward. With this done, you will see the CO2 plug inside; unscrew this and you can pop in a 12g CO2 capsule (we recommend adding a bit of silicone lube to the top of the capsule), tighten it back down again, slide your baseplate back into position and you're good to go! 

If you are looking for spare magazines for your officially licensed SIG AIR pistol? You have found it! This magazine is a replacement original magazine with a 20 round capacity. The magazine can be filled using a speed loader through the feed lips or the fill window at the bottom of the front face of the magazine when the magazine feed spring has been pulled down. The inlet valve can be found at the centre of the baseplate. The magazine has an enhanced baseplate, with an extension to ensure your pistol doesn't slip out of your hands. If you are a CQB player, you'll need at least a few of these!

If you have bagged yourself an interesting anime-inspired GBB pistol you will need the right mags! The Double Bell 18rnd Green Gas Magazine for AM.45 GBB Pistols is styled after a real steel 1911 magazine but is only compatible with Double Bell's funky-lookin' Vorpal Bunny GBB or the super aggressive AM.45 "Chisato".

The magazine suits the style of the AM.45 perfectly with its finger ledge baseplate in either hot pink or matt black. The mag can be filled through the feed lips on the top of the mag or through the feed channel on the front by pulling the follower down and filling from the widened section at the bottom. The fill valve is on the baseplate and as always, the mag will need to be inverted to fill it with gas.

Looking for a spare mag for your STTI ST8 NBB Airsoft pistol? You've found what you need, right here! This magazine is designed for the STTI ST8 and is constructed with a polymer shell, alloy gas reservoir, a steel feed spring and brass valves. The magazine can be loaded through the fill/feed port at the top front of the magazine body and is filled with gas through the fill valve on the baseplate. As an alternative to filling with a speed loader you also have the option of pulling down the magazine follower, found on the left side of the mag and filling by hand.

If you are looking to take your Vorsk VX26 out into the cold look no further! This CO2 magazine will ensure you get the absolute best out of your GBB pistol, even over the winter months. Remember to lubricate both the magazine and pistol to prevent damage to your seals as CO2 contains no lubricant. This magazine uses 12g CO2 bulbs without threading.

If you're looking for spare magazine for your Archon, you've come to the right place. The body is constructed from alloy, for a nice well weighted feel when loading/reloading. Powered by green gas, the mag is filled at the bottom, with the BBs being inserted into the mag using a speedloader via the feed lips or by pulling the spring tab down and filled straight into the BB chamber.

The magazine holds 20 rounds and is fits such models as the EMG Archone Type B.

A spare magazine for the CM.121 and CM.121s which holds a total of 30rnds, and is a necessity when purchasing one of these replicas as they don't take standard AEP mags. It is loaded with BBs from the top of the magazine using a Speedloader.

If you've bagged yourself a bargain backup pistol, perhaps a spare magazine would make it a bit more useful! Introducing the LS B84 Gas magazine, a spare original magazine for the LS B84 NBB pistol. The magazine holds 15 rounds and can be loaded using a speed loader or by hand, through the fill/feed port on the front of the magazine. The gas fill valve is located on the magazine base and this magazine is compatible with green gas, ASG Ultrair, and summer gas.

If you plan on taking your WE Pistole 38 GBB Pistol out on the skirmish field but you feel like one 14rnd magazine is nowhere near enough ammo for you, then you need the WE 14rnd Gas Magazine for P38 Pistol! This magazine is the same as the one that comes with the pistol, so there will be no concerns with compatibility.

It holds 14 BBs and is filled using a speedloader on the feed lips at the top of the magazine. This is a low-capacity but is still 6 ammunition more than the real steel pistol. Its alloy shell protects the polymer internals and gas chamber, which can be filled at the bottom of the magazine in the gas valve.

Pick up some spare magazines for your P38 pistol and take it with you to your next skirmish, or pick up a couple of mags for some test firing in the garden!

If you need to carry some extra rounds for your SRC SR-SP GBB Pistol, you need a couple of these! Like most Airsoft pistol magazines, it features a double-stacked design, capable of holding up to 25 rounds. Ammunition can be loaded from the front either by hand or using an Airsoft speed loader, once the BB guide has been pulled to the bottom of the magazine.

This magazine can be filled with gas via the valve on the bottom through the base plate, which is removable, allowing easier access for any maintenance and can be replaced should the magazine become damaged. On closer inspection of the magazine, subtle Raven logos have been engraved into the bottom of the base plate, a tasteful finishing touch.

Shooting 350 BBs at a target without the added effort of swapping magazines sounds nice right, but usually that comes with the pain and price tag of setting up HPA build, well not anymore! This WE 350rnd Green Gas Drum Magazine allows you to do just that, let off 350rnds without being interrupted by having to swap magazines. It is designed for WE B92 pistols but may work with others, though compatibility cannot be guaranteed.

The magazine is constructed with a hefty alloy gas reservoir with a high-density polymer drum with rubber shock bumpers and an external winding wheel on the front which is easy to wind quickly with or without gloves. The sizeable gas reservoir of this magazine means in most cases you will easily be able to dump the full magazine without a refill, so if you want to run a pistol only this will provide you with more than enough firepower!

A  spare or replacement 25 round Airsoft magazine designed for use in both the RAVEN EU Series and  WE Europe's G-Series of gas blowback Airsoft pistols. 

If you are running the gorgeous Army Armament Sand Viper you will need some equally gorgeous magazines to feed it! The Army Armament 28rnd Magazine for TTI Sand Viper is intended for the Sand Viper, of course, and comes with a CNC machined Aluminium baseplate finished in bronze sporting the Taran Tactical Innovations logo. Being a Hi-capa-based design, this magazine should also fit and feed in most TM-compatible Hi-capa pistols.

The magazine follows the standard GBB pistol mag layout, with the gas fill valve located on the baseplate, requiring both the magazine and your gas can to be inverted to fill. The mag can be loaded through the feed lips or through the feed channel on the front when the follower is pulled down, either by hand or using an Airsoft speed loader. If you want to load up on mags for your Sand Viper but you need the matching baseplates, here you go!

A 25 Round Green Gas Powered Magazine designed for the Airsoft GLOCK 17 Gen4 by UMAREX. This magazine works with the Umarex/VFC Glock 17 GBB and is also compatible with the KRYTAC Maxim 9 GBB but is not compatible with 4.5mm Air pistols. 

A spare Gas magazine for the Army Armament R501 Gas Blowback Airsoft Pistol, which holds a total of 30 BBs and is the perfect way to spend more time in the field playing, and less time in the safe zone reloading. The magazine features a custom Polymer Baseplate which is easily slid to the side to access the inlet valve. 

A gas blowback Airsoft magazine developed by VORSK for their G-Series range of pistols, constructed with an Alloy Body and Polymer base plate. The magazine holds up to 23 rounds and is a direct replacement for the magazine which comes with the pistol, and is filled with BBs from the top or front, and is filled with gas from the bottom once the base plate has been slid to the front. 

If you're looking to bolster your VORSK G-Series pistol magazine with 100% compatible magazines then this is the way to go.