GATE TITAN Drop In MOSFET V2 USB Link Advanced Set

Gate
Code:
217.49
  • Trigger Replacement
  • Optical Trigger Adjust
  • Highly Advanced System

A drop in MOSFET Kit designed for Rear Wired Version 2 Gearbox, which are typically seen in M4 Variant Rifles. This variation of the Kit comes with the MOSFET Unit and the USB-Link. This light version of the kit does not include the tactical programming card.

Full description

Description

The Titan is a complete trigger set replacement, with optical sensors instead of mechanical switches and has a high end software and sensor based sector gear detection, allowing some of the fastest and most efficient AEG builds. 

The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries and is compatible with most V2 Gearbox on the market with no modification. 

The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical ,and has Eight On board Optical Sensors. 

The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and breaking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. 

The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. 

Once installed the MOSFET can be re-programmed via the USB-Link to a Windows based PC, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. Whats important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well they have been implemented.

Features

  • 12 Months Manufacturer Warranty
  • Complete Trigger Set replacement Kit
  • Designed for Highly Efficient AEG Builds
  • Suitable for Stock Guns and Upgraded Guns
  • Great for DMR and Standard Setups
  • Re-programmable with USB Link
  • Optical Sensor Controlled
  • Eight Optical Sensors
    • 1 Gear Sensor
    • 3 Selector Sensors
    • 5 Trigger Sensors
  • Replaces the Cut-off Lever
  • Compatible with most V2 Gearbox on the market without Modification
  • Auto-Adjusting Pre-cocking / Braking system
  • Works with Dual Sector Gear and Short Stroked Gears
  • Detects up to 6 Trigger Positions for the Fine Tuning of the Trigger Break point
  • Capable of Fast Repeat Shooting
  • MILSPEC Board coating
  • Adjustable Trigger Sensitivity
  • Adjustable Pre-cocking Boost
  • Adjustable Fire-Selector Mode
  • Adjustable Burst Mode
  • Adjustable Rate of Fire
  • Two-Stage Trigger Mode, Possible for Semi / Full Auto without using a Fire Selector
  • Sniper Delay Modes
  • Run-away Motor 30 Rounds Limit Mode
  • Protection for the Titan Unit against Over Current, Under Current, and Overheating 
  • Low Battery Warning
  • Over-discharge Battery Protection
  • Configurable Fire Selector
    • Safe - Semi - Auto
    • Safe - Semi - Semi
    • Safe - Semi - Burst
    • Safe - Burst - Auto
    • Safe - Semi - Burst / Auto (Short Press - Burst, Long Press - Auto)
    • Semi - Burst - Auto (Safe Mode via fast switch Safe - Semi - Safe)
  • Kit comes with required parts for Fitting (Please see Special Instructions)
  • Deans Connector Type
  • Protection for Li-Po, Li-Ion, Li-Fe, Ni-Cd Batteries
  • Optical Sensor Test Mode for easier Installation
  • Updateable Firmware via USB-Link on a Windows / MAC PC
  • Statistics and Additional Settings Accessible using a USB-Link with GATE-CS
  • Can be Diagnosed for Errors using the USB-Link
    • UVP1 – your battery is discharged
    • UVP2 – the voltage is lower than 3.8V
    • OCP1 – over current protection
    • OCP2 – the motor power supply circuit is shorted
    • OTP – the drop-in module temperature is too high
    • MOTOR DISC – you pulled the trigger but the motor did not move
  • Smart Fuse System

Package Includes

  • TITAN Drop In MOSFET V2 Module - Rear Wired
  • USB-Link
  • USB Cable
  • Quick start Guides
    • 'USB-Link'
    • 'Titan Drop-In Module'
  • Installation Kit
    • Replacement Female Deans Connector Kit
    • Screw and Shim Set x2
    • Selector Plate Sticker Kit

Special Instructions

Please note, this box contains the USB-Link, everything you need to build and install the TITAN MOSFET.

Should you need any help installing the MOSFET please feel free to call our workshop on: 01484 644709.

Please note that the warranty covers the unit from defects, not improper installation. Please read all user guides before installing, for more information please see the supplied Warranty Card.

Please remember when installing the device to ensure your AEG is clear before use.

Ensure that when wiring up the device the Positive and Negative battery terminals are the correct way around as this will cause immediate damage to the unit.

Please note, that battery protection is not compatible with Ni-Mh and Ni-Cd Battery

For warranty related issues please visit: http://gatee.eu/technical-support/warranty

The GATE Control Station Software can be downloaded at the following links:

Installation Video

Video

Configurable Fire Select

Trigger Sensitivity Adjustment

Hair Trigger Function

Specification

General

Parts & Accessories Type
Internal Parts
Internal Part Type
MOSFET
Patrol Base - Warning Icon
Warnings
Patrol Base - Warning Icon
Parts Fitting
Name Variant
Rear Wired, Front Wired,

Construction

Colour Wheel Greyscale
Item Colour
Black
Construction Icon
Construction
Mil-Spec MIL-V-173C Coated (Moisture and Fungus Resistant)

Part Specific

Part for Power Source Type
Electric

Electric Part Specific

Gearbox Icon
Gearbox Version
V2 Gearbox

Size guide

Parts Fitting

Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff. 

Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.

We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!

Unique Parts

Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.

Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.

If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.