- 95mm Long
- Stainless Steel
- Bearing Spring Guide
A two-piece stainless steel VSR/BAR10 spring guide, designed for enhanced performance and efficiency. The guide is compatible with most Airsoft springs featuring an internal diameter of 11mm or smaller.
Fast Delivery
Delivery & Postage
Here at Patrol Base we ship worldwide, delivering not only to the UK but to most of the EU and select Worldwide locations as well. We provide a working day-by-road service via our handpicked courier services, simply buy your Airsoft guns with us and we'll have them delivered directly to your door.
For more information and to see the country we deliver please check out our Delivery Information Page.
Estimates
Below are some rough postage prices for orders. Please note these are subject to change and are only a rough guide. For a more accurate postage estimate please use the Postage Calculator at the basket.
UK Standard
£6.95
Approx.
UK Next Day
£8.95
Approx.
Highlands / Islands
£24.99*
Approx.
Saturday
£14.95
Approx.
* Scottish Highlands, Islands, and EU post prices can vary wildly. Prices range from £8.99 to £29.99, so please ensure you refer to the Postage Calculator at the basket for the lowest possible price.
Returns
We want you to be delighted with our products and services, so we provide the simple Patrol Base guarantee: if on receiving your item you are unhappy with your item for any reason then simply send it back to us. We will replace or refund the item.
You can return any item for any reason whatsoever, even if you have just changed your mind, within 14 days of receipt of the order. This is in addition to your rights under the Consumer Protection (Distance Selling) Regulations 2000.
For more information on returning products, and how to do it please visit our Returns Policy Page.
Description
Another excellent VSR upgrade component from Laylax, complete with all the usual high quality materials, manufacturing and finish. Suitable for fitting inside springs that have an internal diameter up to 11mm. Incredibly strong, this steel spring guide has a bearing base to keep your compressed springs straight inside the piston and allow a free rotation upon release. This prevents spring and spring guide wearing and any premature breaking. Designed mainly for a VSR platform, this spring guide may fit a variety of other Airsoft spring powered sniper rifles as long as they share similar parts.
Features:
- Solid construction
- Fits inside 11mm upgrade springs
- 2 piece design for re-greasing bearings
- Nipple end to aid locking and keeping straight inside your cylinder
- Bearing braced to prevent spring strain and keep it straight inside your piston
Package Includes:
- PSS10 VSR Spring Guide w/ Bearing
Special Instructions:
This is a 2 part piece, the base screws out from the shaft. Out of the box it should be very stiff and almost impossible to turn. Over time and use it will unsettle and un screw, be sure to service this part regular and just apply a small amount of thread lock before re-assembly. It is rare for the parts to un-do but it has been encountered. This is not a product defect, it comes apart so you can properly grease the ball bearings.
Specification
General
Parts & Accessories Type
|
Internal Parts
|
---|---|
Internal Part Type
|
Spring Guide
|
Weight and Dimension
Product Length
|
Approx. 9.5cm
|
---|---|
Product Width
|
Approx. 1.099cm
|
Construction
|
Silver
|
---|---|
|
Two piece steel construction
|
Part Specific
Part for Power Source Type
|
Spring
|
---|---|
|
VSR / Bar10
|
Package Includes
|
Spring Guide
|
Size guide
Parts Fitting
Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff.
Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.
We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!
Unique Parts
Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.
Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.
If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.
For more information with fitting parts, or should you require help, feel free to get in touch with our Workshop Department via our Contact Us Page.
Terms and Conditions relating to parts fitting can be read on our Terms and Conditions Page.