All External Airsoft Parts & Attachments

If you need more battery space but want to keep your M4/AR-15 AEG slim on the sides, the CYMA Adjustable Whale Stock; Shorty is what you need. This sliding stock is designed for M4/AR-15 buffer tubes and offers a fantastic alternative to common Crane stocks used for rear-wired AEG setups. The shorter variant of the original Whale Stock, this version shaves off a couple of cm, saving weight and length to keep your setup light 'n' tight. 

The advantage of the Whale Stock over the Crane is its slim profile, avoiding the side bulges of the Crane stock in favour of a larger stock "toe" for battery storage. This means you can use a much larger battery than would fit in a buffer tube but still enjoy the slim, snag-free profile of more slimline AR stocks. To access the battery compartment, simply push the catch on the butt plate down and it will hinge open. 

The Whale Stock also features a QD sling socket on each side, ready for a QD sling swivel, along with a conventional sling loop at the toe of the stock for hook or strap-style slings. If you want a new look for your buffer tube-equipped AR AEG but refuse to surrender your massive battery, the Whale Stock is what you need!

A replacement Gas Tube for Airsoft AK models, constructed from Alloy to the original specification as a direct replacement. If you own an AK Model and need a replacement Gas Tube or are looking at making Handguard changes, you can't go wrong with a spare.

If you want to hot swap upper receivers like a real operator, now you can if you have a CYMA CM.097 AEG! The CM.097 Upper receiver is a replacement original part, and could be of use to someone wanting to freshen up an old AEG, or could be used to build a specialised replacement upper receiver so you can change your CM.097 length and battlefield role quickly and easily. The upper receiver comes with a pre-installed dust cover, charging handle, mock forward assist and mock bolt carrier, so no need to source these trim parts separately! This upper is a modern design with the squared off geometry and advanced look, making it a sure choice for a 21st century high speed M4/AR15 build.

Want to keep your Airsoft rifle looking like its real steel counterpart? Then this realistic muzzle break will help! The CYMA M4 Type Flash Hider For 14mm CCW Thread replicates the real M4 muzzle brake seen on service rifles and is constructed from alloy with 14mm CCW threading. Real muzzle brakes are designed to reduce felt recoil by redirecting gas out of the ports on each side, and although you won't get this effect with an Airsoft muzzle brake it will give your Airsoft rifle a modern, iconic look.

An Airsoft replica of the classic M16 style fixed solid stock, designed for use on Airsoft 6mm BB replica M4s, M15s and M16 AEGs. Just like the real stock this replica is based on, the CYMA stock is constructed from dense polymer to create a lightweight and rugged firing platform.

If you want to mount a suppressor or tracer unit to your CYMA CM.702 series sniper rifle, this is the adapter you need! Constructed from steel and designed to mount to the CM.702's 20x1mm female barrel threading, the CYMA 14mm CCW Thread Adapter for CM.702 Series Sniper Rifles provides a 14mm CCW male thread at the tip, ready for the most common Airsoft tracer units and suppressors. 

If your CM.097 lower receiver is damaged maybe it is time to replace it with a fresh one! The CYMA Alloy Lower Receiver for CM.097 M4/AR-15 AEG is a replacement original part for the CYMA CM.097 AEG series and is constructed from alloy. The body pins are constructed from steel for maximum strength, and the fire selector markings are finished in a modern style, with coloured bullet pictograms to indicate each mode of fire.

The set includes all body pins, the fire selector, the bolt catch and the magazine release, meaning no fiddling around trying to swap the trim parts from your old receiver, just drop your gearbox straight in!

If you've lost an SR25 selector switch, this should be helpful! The CYMA Selector Switch Set for CM.098 SR25 AEGs is a replacement original parts set for the CM.098 SR25 series and includes the left and right side selector switches, mounting screws, springs and ball bearings for that lovely "click" between modes.

The switches themselves are constructed from alloy and match the KAC-style selectors found on the CM.098 series, including the scallop on the right side selector and the undercut on the left side selector to allow for full auto fire. Selector switches are always going missing, but with this set handy, your CM.098 won't miss a beat even if the worst happens!

If you want to restore the factory fresh look to your workhorse AK, this part may be of use. The Rear Sight Block for the CM.04x Series is an original replacement part for AKM and AK74 rifles of the CM.04x series. This part will not work on AKS-74U AEGs, but should otherwise fit AKs which use the LCT style of construction. The sight block is constructed from alloy and comes with steel pins to mount it, and includes the handguard disassembly lever but does not include the rear sight or the rear sight leaf spring. The surface finish of this part is a rough textured finish which is a close match for the hard-wearing paint applied to Russian AK variants of the 1960s and onwards.

A 6mm BB Airsoft replica flash hider, designed for CYMA manufactured AK47 and AK74 replica Airsoft Electric Guns. This replica flash hider is an incredibly simple yet effective way to add an additional element of realism to your AEG AKs.

If you want to add a modern touch to your AK, the CYMA Aluminium KeyMod Handguard for AK-47/74 is what you need! This CNC Aluminium handguard is equipped with KeyMod negative space attachment slots at 3, 6, & 9 o'clock with a 20mm Picatinny rail running along the top, ready for a PMC-style forward-mounted red dot sight. 

On each side, we are treated to a pre-installed 20mm Picatinny rail adapter for KeyMod, giving you the option of using more common 20mm Picatinny accessories or removing the adapters to mount more modern KeyMod solutions. The handguard itself is constructed in two parts, allowing you to use both or simply the upper or lower handguard, depending on your build requirements. If you're going for the modern tactical AK look, the CYMA Aluminium KeyMod Handguard for AK-47/74 is perfect for your build!

If you're looking for an ergonomic enhancement for your M4, the CYMA Enhanced Pistol Grip for M4/AR-15 AEG is a great affordable option! Made from robust high density polymer, this pistol grip is set at a more vertical angle than the average, making it fantastic for shooting with modern stances with the stock fully collapsed.

Each side is rocking dot texture, with additional linear texture on the front and rear, maximising gripping qualities for easy wet weather use. Compatibility-wise, this grip should fit almost every M4/AR-15 AEG on the market, provided it is based on the original TM M4 AEG internal and external design.

If you want to add some tactical trimmings to your AK an extended fire selector would be a good call. The CYMA Tactical Extended Fire Selector Lever for AK47/74 AEG is constructed from stamped steel and is a modernised design with a cutout for the AK bolt handle and a ledge that can be used to select fire modes from a firing grip.

With this selector installed you no longer need to take your hand off the pistol grip to select your fire mode; simply move the new selector using the ledge and your trigger finger. This makes a massive difference when it comes to handling an AK and allows it to go toe to toe with the AR platform in ergonomics and efficiency. A perfect item for any Tactical AK or PMC style custom AK build, this selector lever not only looks super slick but also makes your AK super slick to use!