Airsoft Magazines

A gas blowback Airsoft 6mm BB gun magazine designed for WE Europe's F228 series and F229 series pistols. A perfect spare to increase your trigger time, without stopping to reload. 

This magazine is specifically for the STTI ST92F, in that this is a non-blowback mag and features incredible gas efficiency. The magazine is constructed from high high-density polymer and is incredibly lightweight compared to tis alloy counterparts. The magazine holds 23 rounds, filled at the top using a speed loader and the gas is filled at the bottom with green gas.

This alloy magazine can hold up to 24 rounds to use with any generation of the Raven R series or WE Europe F series of pistols. The mag uses green gas, which can be added via the valve on the base of the magazine. For filling with BBs, there is a window on the front which is wider towards the base, accessed when the follower is pulled down.

The Novritsch 32rnd Gen.3 Gas Magazine is designed for Novritsch SSX23 or MK23 Pistols, but it is compatible with non-blowback pistols from Marui, KJW, and ASG. It is constructed from alloy, giving it a nice weighted feel when reloading. The magazine holds green gas which is refilled at the bottom. The BBs are loaded into the magazine by pulling down the spring tab and filling the BB chamber with a speedloader. This mag has a 1-stage valve and a hard rubber gas router for a snappy trigger return.

Being a product by Novritsch, we know that high quality is a given and satisfaction can be guaranteed. Pick up a Novritsch 32rnd Gen.3 Gas Magazine for SSX23/303 as a spare mag for one of your sidearms, so you can have that extra clip of ammo when you need it most.

A Spare Gas Blowback Magazine for any generation of the WE F226 range. 

If you're looking for spare mags for your Golden Eagle Hi-capa, here they are! The 25rnd Green Gas Magazine for Hi-capa GBB is constructed from alloy with brass valves, rubber o-rings, a steel feed spring and a polymer baseplate and is a green gas magazine. The mag can be filled using the fill valve on the base plate and is loaded with BBs either through the feed lips at the top of the mag or by pulling the follower down and loading BBs in through the front.

This magazine is compatible with the Golden Eagle Hi-capa series but is patterned after the TM design so should also be compatible with other Hi-capa platforms as long as they use the Tokyo Marui internal system.

An Alloy constructed 23rnd magazine for the Vorsk Vengeance Hi-Capa Gas Blowback Pistol.

The Novritsch 24rnd Magazine is designed for Novritsch SSX23 or MK23 Pistols, but it is compatible with non-blowback pistols from Marui, Y&P, Stti, KJW, and ASG. It is constructed from alloy, giving it a nice weighted feel when reloading. The magazine holds green gas and can be refilled at the bottom, the BBs can be inserted into the magazine by pulling down the spring tab and filling up the BB chamber with a speedloader. This mag comes with a 1-stage valve and has a hard rubber gas router for a snappy trigger return.

Being a product by Novritsch, we know that high quality is a given and satisfaction can be guaranteed. Pick up a Novritsch 24rnd Magazine for SSX23/MK23 as a spare mag for one of your sidearms, so you can have that extra clip of ammo when you need it most.

Need some big mags for your big handgun? The Cybergun Desert Eagle green gas magazine should do the trick! This magazine is designed for the Cyber Gun Airsoft Desert Eagle L6 GBB and holds approximately 27 BBs which can be loaded using a speed loader through the feed lips at the top of the magazine. This magazine is a green gas magazine and can be filled through the fill valve on the magazine's baseplate, and can also take summer gas to keep the FPS down to reasonable levels on hot days. The magazine is constructed from alloy with polymer feed lips, with a steel feed spring and brass valves, and has realistic mock witness holes on each side, matching the cut-outs in the real Desert Eagle magazine used for gauging how many rounds are left.

A spare magazine for WE Europe's Makarov W65U pistols. The magazine is constructed entirely from Alloy and features an Alloy base plate, making the magazine durable and more resistant to drops. 

A spare magazine for WE Europe's Makarov W65U pistols. The magazine is constructed entirely from Alloy and features an Alloy base plate, making the magazine durable and more resistant to drops. 

A gas blowback CO2 magazine, designed for Cyber Gun's series of Colt 1911 Rail Gun Airsoft replica pistols.

A magazine designed for use in the WE Europe's GALAXY Series of pistols. Each magazine is of a full metal construction and holds up to 25 rounds.

A Green Gas, 25 round magazine for the UMAREX Heckler & Koch USP .45 GBB Pistol.

A gas blowback Magazine for the WE Europe EU-Series Pistols EU19, and EU23.

An Airsoft 6mm BB gas blowback magazine for the 5.1 Hi-Capa pistol series, with a double stacked design it has a capacity of up to 25 bb rounds. 

Suppose your Tokyo Marui Saiga-12K needs some spare magazines to keep it fuelled during a skirmish, the Tokyo Marui 45rnd Saiga-12K Magazine is exactly what you're searching for! This magazine has a polymer shell, alloy internals and a steel spring, which makes it very strong and reliable. This magazine is sure to survive whatever a skirmish may throw at you!

The magazine holds 45 BBs and features polymer feed lips. This is also where you load the magazine using a speedloader. The gas valve is found at the bottom of the magazine. To load this magazine, you have to use an AK-style "rock and lock" method. This means you have to insert the front section of your mag first, then "rock" your magazine back to lock it in place in your Saiga-12K.

The magazine can be removed from its polymer shell to view the internals and see the internal temperature sticker, this sticker shows what temperature the magazine is. To remove the polymer shell, press the button located at the rear of the magazine, then pull the shell from the internal magazine.

A time with a full alloy outer construction and base this magazine is durable yet lightweight. The feed lips and BB follower are polymer and are replaceable. 

A replacement or spare Magazine for a RAVEN branded Hi-Capa 4.3 or 5.1. It holds a total of 25rnds and is powered by a 12g CO2 Bulb, which means it works far better in the cold than a Green Gas Magazine. This Magazine will provide much stronger recoil and better shots-per-magazine, especially when Winter is upon us.

If you need mags for your ASG P-10C CO2 version, here you go! Just like the original mag supplied with your ASG P-10C CO2 GBB pistol, this magazine holds 22 BBs and is constructed from alloy with a high-density polymer baseplate. Loading the mag is the same procedure as other GBB magazines, either load through the feed lips at the top or through the follower channel on the front when the follower is held down. You can use a speed loader or do it by hand, depending on your timescale!

While the CO2 and Green Gas versions of the P-10C are cross compatible, we have been told specifically by ASG not to use CO2 mags in the polymer slide equipped green gas model to avoid premature wear and tear and potentially, catastrophic failure. We suggest you heed this warning!

The CO2 compartment is inside the shell and accessible with the baseplate removed. To achieve this, simply pull upwards on the polymer tab at the bottom of the follower channel and slide the baseplate forward. With this done, you will see the CO2 plug inside; unscrew this and you can pop in a 12g CO2 capsule (we recommend adding a bit of silicone lube to the top of the capsule), tighten it back down again, slide your baseplate back into position and you're good to go! 

An Alloy constructed Gas Powered magazine for the SRC branded TT-33 replica (SR-33). It holds a total of 11rnds and is filled from the bottom with Green Gas via the Inlet Valve. The follower is easy to pull down from the side, and it can be easily loaded by hand or using a Speedloader. Be careful not to let the follower spring up otherwise the feedlips could be damaged.

If you need spare magazines for the KRYTAC Maxim 9 GBB you have found what you need! Like the original mag, these magazines are constructed with a lightweight aluminium shell which makes them far lighter than equivalent GBB mags, meaning you can carry more and move faster!

Each magazine holds 24 BBs and can be loaded either through the feed lips at the top of the magazine body, or through the feed channel at the front of the magazine by first pulling the follower down to the bottom. The gas fill valve is on the rear of the magazine and this magazine is designed for use with Green Gas. This magazine is the original mag supplied with the Maxim 9 and is also compatible with the UMAREX/VFC Glock 17 GBB, both gen.4 and gen.5 flavours.

If you want to keep your beast of a Novritsch pistol shooting perfectly in cold weather, you'll need one of these! The Novritsch 31rnd CO2 Magazine for SSP1/SSP5 GBB Pistol is constructed from alloy with a polymer baseplate and is compatible with both the SSP1 and SSP5 GBB pistols.

The mag is loaded either through the feed lips or the follower channel when the follower is held down using a speed loader or loading tool. If you're new to CO2, we recommend giving our CO2 guide a quick read so you can stay abreast of maintenance and CO2-specific safety issues.

This mag uses 12g unthreaded CO2 capsules, one of which needs to be installed inside the magazine shell. To access the CO2 compartment, simply press the small button on the bottom and slide the baseplate off. Underneath, you will find the CO2 plug which can be removed with the included Allen key or a flat tool if you don't have the Allen key handy. Install your CO2 capsule inside, tighten the plug down until you hear the capsule pierce and replace the baseplate; you are now good to go!

If you have the desire to dump 350 rounds in one long burst from your GBB pistol but you don't want to go the HPA route this is your chance! The WE Europe 350rnd Green Gas Drum Magazine is designed for WE's GBB EU series which means it will also work in the Action Army AAP-01.

The magazine is constructed with a hefty alloy gas reservoir with a high density polymer drum with rubber shock bumpers and an external winding wheel on the front which is easy to wind quickly with or without gloves. The sizeable gas reservoir of this magazine means in most cases you will easily be able to dump the full magazine without a refill, so if you go pistols only and you need extra firepower to compete, this will suit you well!

An extended 32 round magazine designed for the WE P-Virus P226 gas blowback pistol. 

If you're running a WE GBBR, whether it's the SCAR-L, L85/SA80, Type 91, Keltec PLR-16, KAC PDW or M4 variant, this is the one mag you need to keep them all well-fed! Constructed with a steel shell, alloy/polymer internals and brass valves, this magazine is designed for WE Open Bolt GBBRs and holds 30 BBs filled through the feed lips, either with a speed loader or by hand. This V3 version has been refined to improve the reliability and consistency, to ensure your replicas feed perfectly every time.

With wide compatibility and a strong but relatively light build, these magazines even allow you to switch off the "bolt lock" function using the catch on the top, meaning you can dry fire for a laugh or to practice weapons handling without holding the bolt catch while doing it. Compatibility-wise, these are strictly for WE Open Bolt GBBR rifles but will work in any WE Open Bolt GBBR which takes STANAG-style mags.

These magazines are perfect for those who have the 3.8 Hi-Capa pistol, allowing you to have more shots available and allowing you to practice pistol loading drills.

A magazine designed for WE brand AR36 / G39 Airsoft gas blowback rifles.

Do you find yourself running out of ammo way too often? We have the solution! The Tokyo Marui 90rnd Saiga-12K Long Magazine is exactly what you need to keep on blasting for longer. This magazine has a polymer shell, alloy internals and a steel spring, which makes it very strong and reliable. This magazine is sure to survive whatever a skirmish may throw at you!

The magazine holds a whopping 90 BBs and features polymer feed lips. This is also where you load the magazine using a speedloader. The gas valve is found at the bottom of the magazine. To insert this magazine, use an AK-style "rock and lock" method. This means you have to insert the front section of your mag first, then "rock" your magazine back to lock it in place in your Saiga-12K.

The magazine can be removed from its polymer shell to view the internals and see the internal temperature sticker, this sticker shows what temperature the magazine is. To remove the polymer shell, press the button located at the rear of the magazine, then pull the shell from the internal magazine

Suppose you're looking for some extra magazines for your gas blowback AK platforms, if so, then the GHK 40rnd Magazine for AK74 GBBRs is exactly what you need! It has a polymer shell and alloy internals with a steel spring, which makes it very robust and reliable, sure to survive even the most intense of skirmishes. The magazine features a slick black design that matches most AK platforms perfectly.

The magazine holds up to 40 rounds, and features Polymer feed lips, which are also the fill location using an Airsoft speedloader. The magazine gas fill valve is found at the rear using any Airsoft green gas. The insertion method for this magazine is the traditional AK "rock and lock" style, this means you have to insert the front section of your mag first, then, "rock" your magazine back to lock it in place in your AK rifle.

If you want a high-quality magazine that will never let you or your gas blowback AK down, the GHK 40rnd Magazine for AK74 GBBRs is certainly the choice for you!