Airsoft 7.4v Li-Po Batteries

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery with a Mini-Tamiya connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a buffer tube battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 1.3cm x 1.5cm with approximately 9cm of wiring between the battery and connector

An ultra thin and lightweight crane stock battery, perfect for squeezing into the ever more popular Airsoft crane stock.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

If you need an Airsoft battery that fits in almost anything and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo/ LiFe/NiMH Balance Charger, a Safe Charging Bag and an ASG 7.4V 1300mAh LiPo Battery in Crane configuration with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs and capable of fitting inside Crane stocks, fixed stocks and most handguards! If you have multiple different AEGs and you want a battery to fit them all, chances are this one will! 

The dimensions of the included battery are as follows: 10.1cm x 0.7cm x 2cm per cell group (2x cell groups on each battery) with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Crane Stock, M4/AR-15, SMG-5 & AK Fixed stock, AR-36 & SMG-5 handguards, Tokyo Marui SCAR-L/H NGRS stock, most M4/AR-15 buffer tubes. 

A 7.4v Lithium Polymer Battery designed for use in battery compartments with limited space for a thin, but long battery.

If you need a battery to fit into a tight place, Evolution Airsoft have you covered with the 7.4V 1100mAh 20C LiPo Stick Battery. This battery comes pre-wired with a Deans battery connector, also known as a "T-Plug" but is packaged with a Deans to mini-Tamiya adapter, meaning it can be used with almost any Airsoft AEG around.

The battery is a 2 cell 7.4V LiPo battery in stick configuration, meaning the cells are bound together into a single unit. The wire length between the battery and connector is approximately 10cm, the continuous discharge rate is 20C and the peak discharge rate is 40C. Whether you need a battery for your Airsoft gun or another electronics hobby which requires a compact power source, this Evolution Airsoft battery will do the trick!

Suitable not only for Airsoft but for RC vehicles and toys too, this  7.4v 2200mAh LiPo Stick Battery will fit in tight areas like stock tubes and handguards where other batteries wouldn't normally.

If you're looking for the very smallest of LiPo batteries, you've found it. Measuring 4x1.3x2cm, this battery can be used to power the FCU in the V12 engine, in addition to other HPA systems with a mini-JST type connector.

The battery has a voltage of 7.4v, a capacity of 250mAh and a discharge rate of 20C and features a cable length of roughly 10.5cm

A 7.4v 1450mAh LiPo stick battery suitable not only for Airsoft but for RC vehicles and toys too.

If you need a battery for your M4/AR-15 AEG Crane stock and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configuration with a Deans connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2 cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

If you need a battery for your handguard or full stock battery compartment this should do the trick! The 7.4v 1600mAh 25C LiPo Battery from Giant Power is nice and compact, measuring 9.5x1.2x3cm approximately, making it great for handguard battery compartments in SMG-5 and AR36 AEGs and also an easy fit in M16 and AK full stocks.

The battery is pre-wired with a mini-Tamiya battery connector and is in block configuration, meaning both cells are bound together. The wire length between the battery itself and the connector is approximately 10cm and the continuous discharge rate is 25C, making this battery ideal both for Airsoft and any electronics hobby which requires a compact power source.

Giant Power are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery's dimensions are 10x1.2x3cm with a cable length of roughly 10cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery with a Deans connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a buffer tube battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 1.3cm x 1.5cm with approximately 9cm of wiring between the battery and connector. 

A 7.4v Lithium Polymer Battery designed for use in battery compartments suited to small, slim batteries with two separate cells. This is a "Crane" stock style battery, also known as the "Nunchuck" configuration.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A LiPo battery with a universal electric pistol connection that will allow it to be used in pretty much every Airsoft Electric Pistol we can think of.

If you want the biggest stick battery you can squeeze into your M4/AR-15 buffer tube, this is probably it! The Specna Arms 7.4v 2000mAh 15/30c LiPo Stick Battery is pre-wired to a mini-Tamiya battery connector and designed for slim and long battery compartments. The battery is a 7.4V LiPo with a capacity of 2000mAh, continuous discharge rate of 15C and maximum discharge rate of 30C.

The battery measures 12.3 x 1.6 x 1.8cm approximately and should fit into most M4/AR-15 buffer tubes, though some with less space inside may require that you leave the stock in an extended position. The wire between the cell group and connector is approximately 10cm, giving you plenty of flexibility to fit the battery where you need it. As always, measure up before you buy!

If you're looking for a fixed stock or other relatively large battery compartments this one should do the job! The 7.4V 1500mAh 25C Block LiPo Battery from Electro River is the perfect battery for full stocks found on M16, AK platforms, SMG-5 handguards and G3 Airsoft AEGs.

The battery measures approximately 9 x 1.3 x 3.5cm with a wire length of roughly 9cm with a mini-Tamiya battery connector, not to be confused with Deans connector, however, adaptors are also available.

The battery is a 7.4V 2-cell battery in block configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG, though make sure you measure before ordering!

Giant Power are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 35C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery's dimensions are 7x1.5x3.4cm with a cable length of roughly 7.5cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.

A LiPo saddle battery designed to fit in handguards in replacement of the traditional 1600mAh NiMH blocks/saddles (G36 handguards etc).

If you want a block battery for a handguard or PEQ battery box, this one should do it! The GFC 7.4v 1500mAh 20/40c LiPo Block Battery is pre-wired to a mini-Tamiya battery connector and designed for handguard battery compartments such as those on front-wired SMG-5 and AR36 AEGs. The battery is a 7.4V LiPo with a capacity of 1500mAh, continuous discharge rate of 20C and maximum discharge rate of 40C.

The battery measures 8.7 x 1 x 3.3cm approximately and should also fit into some of the bigger PEQ-style battery boxes, though we suggest measuring up before buying to avoid disappointment. The wire between the cell group and connector is approximately 10cm, giving you plenty of flexibility to fit the battery where you need it.

If you need an Airsoft battery for an AEG with a fixed stock battery compartment and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and an Electro River 7.4v 2300mAh 20C LiPo Block Battery with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs with battery compartments within their fixed stocks. 

The dimensions of the included battery are as follows: 10cm x 1.5cm x 3.4cm with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Fixed stock, AK47/74 Fixed Stock, SMG-5 Fixed Stock, G3 Fixed Stock. 

If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Electro River 7.4v 1200mAh 25C LiPo Stick Battery measures approximately 11.5 x 1.4 x 1.5cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Deans connector and the length of wire between the cell group and the connector is approximately 9cm.

The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C and a maximum discharge rate of 50C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!

If you're looking for a tiny LiPo battery for your Novritsch SSE18 or CYMA CM.1xxS MOSFET equipped AEP, this is what you need. The Novritsch 7.4V 600mAh LiPo Battery measures approximately 7.3 x 1.5 x 1cm and is pre-wired with a Mini-Deans battery connector and a 3 port balance connector. 

As with other LiPo batteries, this battery should only ever be charged on a LiPo balance charger, preferably in a battery charging bag and should not be left on charge unattended under any circumstance.

If you need a battery for your top wired AK AEG or SMG-5K and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1200mAh LiPo Slim Stick Battery with a Deans connector; an ideal setup for a Deans equipped top wired AK or SMG-5K AEG with a battery compartment inside the receiver.

The dimensions of the included battery are as follows: 19cm x 0.6cm x 1.6cm with approximately 9cm of wiring between the battery and connector. 

A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.

If you need a compact 7.4V LiPo for your buffer tube, PDW stock or other cramped battery compartment, the VP Racing 7.4V 800mAh 20c LiPo Stick Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and measures 10.2 x 1.1 x 1.9 cm with 5cm of wire length, making it suitable for most Airsoft AEGs, even those with small battery compartments. As always, we recommend measuring thoroughly to ensure it fits before ordering!

If you need a slim stick battery for your M4/AR-15 AEG buffer tube or a top wired AK AEG this will do the trick! The Electro River 7.4v 1200mAh 25C LiPo Stick Battery measures approximately 11.5 x 1.4 x 1.5cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5k platforms. The battery is pre-wired to a mini-Tamiya connector and the length of wire between the cell group and the connector is approximately 9cm.

The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C and a maximum discharge rate of 50C, making it great for almost any Airsoft AEG, though make sure you measure before ordering!