Airsoft 7.4v Li-Po Batteries

If you're looking for a battery for a top-wired AK setup or an SMG-5K, this is the one! The Giant Power 7.4V 1300mAh 25C LiPo Slim Stick Battery is ideal for long, slim battery compartments, measuring approximately 18cm x 0.8cm x 1.6cm with a 5cm wire length, and is pre-wired to a Deans/T-plug connector. 

This 7.4V LiPo consists of 2 cells bound together into a single cell group, with a 25C continuous discharge rate and a capacity of 1300mAh. 

If you're running a CYMA MOSFET-equipped AEP or the Novritsch SSE18 AEP, this is how you keep your electric pistol in the fight all day! The IPower 7.4V 680mAh 20c LiPo Battery For CYMA MOSFET AEPs is designed specifically for the CM.1xxS MOSFET-equipped AEP series and also fits the Novritsch SSE18, pre-wired to a mini-Deans connector and balance plug. Please note, this battery will NOT fit standard AEPs.

The battery can be charged and recharged using a standard LiPo balance charger, and the balance lead MUST be connected to ensure the battery is charged safely. We also recommend charging in a battery charging bag for maximum safety.

Those of you looking for a battery with a truly large capacity, you've come to the right place! The battery is perfect for larger battery compartments such as SMG-5, G3, M16 and AK platforms with fixed stock battery compartments. The battery has a voltage of 7.4v, a capacity of 2800mAh and a continuous discharge rate of 25C with a maximum discharge rate of 50C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.

The battery measures 13x1.1x4.2cm with a cable length of roughly 10cm.

If you're looking for spare batteries for your EMG JW3 AEP, this Specna Arms Gens Ace 7.4V 25C 620mAh G-Tech battery for AEPs is ideal! A 7.4V 2S LiPo with 620mAh capacity, this battery is pre-wired to a mini-Deans connector and a G-Tech balance plug. The G-Tech balance plug allows you to charge this battery on either a standard LiPo balance charger or the advanced G-Tech Charger from Gens Ace.

During our testing, we found this battery to be an incredibly tight fit in most AEPs, so we only recommend it for the EMG CM.138 JW3 AEP. Please note, if you do attempt to install this battery on other AEPs, it is likely you will damage the outer coating, which will invalidate your warranty. If you need to keep your JW3 AEP in the fight for longer, the Specna Arms Gens Ace 7.4V 25C 620mAh G-Tech battery for AEPs is the way to go!

A LiPo Battery for Airsoft Electric Guns, with a 7.4V rating and 1200mAh capacity. This LiPo Battery is laid out in a Nunchuck / Crane Stock configuration, which makes it ideal for Handguards and AR Stocks thanks to the slim design. If you own a battery-powered Airsoft Gun and need a compact LiPo with a sensible capacity, then these are perfect for you. Features a Mini Tamiya Connector.

An ideal battery for those who have very limited space or for those who have a front wired PEQ box style setup or RC cars. With a 1000mAh 30C discharge expect a good rate of fire but 2 or 3 are recommended for a full day of constant shooting.

A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.

A compact 7.4v two cell stick battery that is ideal for squeezing into small spaces like stock tubes, especially the battery spaces on Honey Badgers and compact weapons with an extending skeleton stock.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A LiPo saddle battery designed to fit in handguards in replacement of the traditional 1600mAh NiMH blocks/saddles (G36 handguards etc).

This battery features a wider and flatter butterfly style configuration and while it won't fit in crane stocks it is perfect for larger areas such as AR36 handguards and full stock rifles. The battery has a voltage of 7.4v, a capacity of 1500mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however adaptors are available.

The battery consists of two cells working in tandem with each other, with each cell measuring 8.5x0.6x3.4cm with a cable length of roughly 9cm.

An ultra-thin and lightweight battery, perfect for squeezing into even the tightest spots. This battery provides 1200mAh of power with a discharge rate of 30c. Being short and wide, this battery is perfect for PEQ boxes and solid stocks.

If you're looking for a battery for an AR36 or SMG-5 handguard, this is the one! The Giant Power 7.4V 1500mAh 25C LiPo Flat Nunchuck Battery is ideal for AEG handguards and fixed stock, measuring approximately 9.5cm x 2.8cm x 0.6cm (per cell) with a 5cm wire length, and is pre-wired to a Deans/T-plug connector.

This 7.4V LiPo consists of 2 cells configured as two cell groups, with a 25C continuous discharge rate and a capacity of 1500mAh.

If you run a front-wired AEG with limited battery space, storing your battery in a PEQ-15 battery box could be the solution! This 7.4V 850mAh 20C LiPo battery from Electro River is designed to fit into cramped spaces and is the perfect size for use in a PEQ-15 battery box. The battery measures  5.5 x 3 x 1.5cm approximately, and the wire length between the cell group and connector is approximately 11cm.

The compact size of this battery makes it great for both Airsoft and any other electronics projects you have on the go, providing plenty of juice in a smaller form factor. The continuous discharge rate of this battery is 20C, and its peak is 60C, giving you a nice snappy response without overdoing things!

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

If you like to be at the cutting edge of battery technology when it comes to Airsoft, you're going to want to check this out! The Gens Ace 7.4V 25C 1000mAh Airsoft LiPo Battery - Mini-Tamiya is a slim LiPo battery intended for Airsoft buffer tube battery compartments, AK top covers and other cramped spaces requiring a single cell group. The discharge rate is 25C, giving you a snappy response without risking overspin in most setups, and the capacity is 1000mAh, meaning you might need two to get through a full game day.

Where this battery differs from the norm is its Smart Balance Connector which interfaces with the Gens Ace IMARS Mini Charger, communicating the battery type and current charge levels and immediately commencing optimal charging as soon as this "Smart Battery" is connected. Compared to legacy smart chargers, this saves loads of time but unfortunately means that this battery cannot be charged using a standard LiPo balance charger.

If you need a battery for your top wired AK or SMG-5K AEG and would rather get everything you need in one place, here it is! This bundle includes a LE-3 LiPo Balance Charger, a Safe Charging Bag and a Giant Power 7.4V 1300mAh LiPo Slim Stick Battery with a Mini-Tamiya connector; an ideal setup for a mini-Tamiya equipped top wired AK or SMG-5K AEG with a battery compartment inside the receiver.  

The dimensions of the included battery are as follows: 18.5cm x 1cm x 2cm with approximately 9.5cm of wiring between the battery and connector. 

This tiny Specna Arms 7.4V 1300mAh 30C Micro PEQ LiPo Battery is the best fit for a PEQ box wired gun, such as the Specna Arms SA-H01. It can squeeze into some tight spots, with its dimensions of 6.5x1.5x3.5cm; it will sadly not fit in PDW stocks, but may fit in some SMG and AR36 handguards.

As it is a 7.4V LiPo, it is compatible with almost every Airsoft gun, plus, its Deans-style connector is optimal as most modern Airsoft guns are coming with Deans connectors installed due to its lower electrical resistance when compared with Tamiya connectors. If you need a small battery for your Airsoft platform, the Specna Arms 7.4V 1300mAh 30C Micro PEQ LiPo Battery; Deans could be the best choice for you!

If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Gen's Ace 7.4v 1500mAh 25C LiPo Stick Battery measures approximately 12x1.5x1.6cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Mini-Tamiya connector and the length of wire between the cell group and the connector is approximately 6cm.

The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!

If you need a super-tiny battery for a PDW stock, EMG Autobot Speedloader or other cramped battery compartment, check this out! The Giant Power 7.4v 560mAh 25c LiPo PDW/Autobot Stick Battery measures a mere 7.5cm x 1.1cm x 1.5cm approximately, with 5cm of wire length, pre-wired to a Deans/T-plug battery connector. 

Being super-duper small, this battery will fit neatly where others won't, including in L85 platforms wired to the pistol grip (A3 & AFV), M4/AR-15 platforms with PDW stocks and other tight battery compartments. It's also a perfect fit in EMG's Autobot Speed Loader!

This ultra-thin Specna Arms 7.4V 1000mAh 30C Micro PEQ LiPo Battery is perfect for a PEQ box wired gun, such as the Specna Arms SA-H01. It can squeeze into some tight spots, but with its dimensions of 6.5x1x3.5cm, it will sadly not fit in PDW stocks but may fit in some SMG and AR36 handguards.

As it is a 7.4V LiPo, it is compatible with pretty much every Airsoft gun, and its Deans-style connector is optimal as most modern Airsoft guns are coming with Deans connectors installed due to its lower electrical resistance when compared with Tamiya connectors. If you need a teeny tiny battery for something, the Specna Arms 7.4V 1000mAh 30C Micro PEQ LiPo Battery; Deans could be your best shout!

A LiPo Crane Stock battery designed to fit in stocks and small spaces which other large batteries do not fit. The battery is also know as a Nunchuck battery, with the cells connected via the wires allowing them to be placed down the side of barrels or in an M4 Crane Stock.

A Standard powered Airsoft Battery, designed to be used in almost all Airsoft AEG weapons with a mini-Tamiya connector, providing the perfect amount of power for most Airsoft Weapons. 

A 7.4v 1450mAh LiPo stick battery with Deans connectors, suitable for Airsoft in addition to other application such as RC vehicles and toys too.

If you need a compact stick battery for an AR buffer tube or PDW stock, the Giant Power 7.4V 1000mAh 25C LiPo PDW Stick Battery fits the bill! This compact stick battery measures approximately 9cm x 1.1cm x 1.6cm with 5cm of wire length, pre-wired to a Deans/T-plug battery connector. 

This 7.4V LiPo consists of 2 cells bound together into a single cell group, with a 25C continuous discharge rate and a capacity of 1000mAh. This uniquely small battery is ideal for practically any battery compartment and a great choice for PDW stock-equipped AEGs, though we recommend measuring up before ordering to be safe!

If you need slim 7.4V crane stock LiPo for your crane stock or handguard battery compartment, the VP Racing 7.4V 1000mAh 20c LiPo Crane Stock Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and is comprised of 2 cells, each of which measures 11 x 1.5 x 0.5 cm. The wire length between the cells and connector is approximately 10cm, giving you a bit of flexibility to ensure the battery is installed properly. As always, we recommend measuring thoroughly to ensure it fits before ordering!

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards  and comes fitted with Deans connectors instead of the standard Tamiya for upgraded Airsoft Guns.

A high quality 1300mAh 7.4V LiPo battery suitable for Airsoft and RC use, coming fitted with an upgraded Deans Connector rather than the standard Mini Tamiya.

If you need a compact 7.4V LiPo for your buffer tube, PDW stock or other cramped battery compartment, the VP Racing 7.4V 800mAh 20c LiPo Stick Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and measures 10.2 x 1.1 x 1.9 cm with 5cm of wire length, making it suitable for most Airsoft AEGs, even those with small battery compartments. As always, we recommend measuring thoroughly to ensure it fits before ordering!

VAPEX are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 30C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery's dimensions are 10x1.2x3cm with a cable length of roughly 10cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.