All Electric Parts

If you're done with AEGs and want to revamp your build for HPA, the GATE PULSAR D Dual Solenoid HPA Engine is a fantastic option. Designed for Version 2 AEG gearboxes, the PULSAR D is designed to work with a GATE TITAN™ II V2 ETU (HPA Version), giving you unlimited advanced programming options along with the bob on consistency, top-tier accuracy, killer rate of fire and wealth of tuning opportunities HPA builds are known to provide.

The set includes the complete engine but will require a V2 gearbox shell, V2 trigger and TITAN™ II ETU HPA Version to complete the build. When compared to the original and more affordable PULSAR S, the PULSAR D offers a higher FPS range, universal compatibility with AEG nozzles, less precision required in the assembly of the build and impressively high air efficiency, using only 0.7 PSI per shot on average at 90 PSI with a 0.8L air tank.

The PULSAR D also has the edge in accuracy and versatility over the simpler single solenoid PULSAR S, being suitable for any build objective, from CQB monster to DMR dominator. As with all internal upgrades, we only recommend this engine to those who are confident working on AEG and HPA internals, but if you're ready for the PULSAR D, you're sure to be impressed!

For a sturdy upgrade to your AEG the FPS X-Ring is a piston head seal with a quadrilobate section, which during dynamic stresses are not subject to seal rounding.

X-Rings have less wear than O-Rings as they require less radial pre-stress which results in lower contact pressure.
A lubricant reservoir can be created between the sealing lips using silicone.

Installing this ring will optimise the sealing effect thanks to a better pressure distribution due to the square section.
The X-Ring eliminates any negative effects due to the closing line of the mould, as this is located in the groove between the two lips.

If you've had a cut-off lever failure or you like to keep parts on hand just in case the worst happens, the G&G Armament Cut Off Lever For V2 Gearbox is perfect. This is a replacement original part constructed from alloy, compatible with most version 2 gearboxes on the market.

The cut-off lever is a piece that sits between your trigger and sector gear and serves to interrupt or disconnect the trigger once your gearbox has made a complete cycle, very useful!

This polymer constructed piece is designed to screw into your outer barrel assembly, to lock your Inner Barrel in place and removing any motion that is is able to have. This will help improve accuracy and consistency by stopping the inner barrel from wobbling as the BB travels through it. There is an option available for most major platforms, and is an absolute must-have piece for those seeking perfection in their rifles.

This polymer constructed piece is designed to screw into your outer barrel assembly, to lock your Inner Barrel in place and removing any motion that is is able to have. This will help improve accuracy and consistency by stopping the inner barrel from wobbling as the BB travels through it. There is an option available for most major platforms, and is an absolute must-have piece for those seeking perfection in their rifles.

If you are looking for an excellent replacement piston for your AEG then look no further! The RetroArms 14.5 Steel Tooth Piston is the perfect piston upgrade. Its injection moulded carbon-reinforced polymer ensures premium quality and consistency, the fourteen-and-a-half steel teeth are highly wear-resistant and greatly extend the lifespan, and it also keeps your Airsoft rifle performing up to standards. The half-tooth allows the piston to be picked up by the gears more easily and minimises the chance of the teeth bouncing off the gear and causing internal damage.

The RetroArms 14.5 Steel Tooth Piston is great for high-performance builds and is designed for version 2 and version 3 gearboxes. Make your AEG premium with this simple upgrade piece!

A complete V6 gearbox designed as a replacement for CYMA P90 AEGs to breathe new life into your weapon.

A pre-assembled, ready to use complete gearbox set designed for use in 6mm Airsoft BB replica M14 AEGs. With all the components assembled and in place, this gearbox is ready to be dropped into place in your M14 AEG, replacing any old and worn out gearboxes.

If you have worn out your AEGs trigger or you want the mil-spec look to replace your current trigger, this is perfect for you! The G&G Armament Trigger For V2 Gearbox is constructed from alloy with a textured finish and is patterned after the standard curved "Milspec" trigger found on the M4A1 rifle, MK18 MOD.0 and MOD.1, along with most other M4/AR-15 rifles used in military service in the real world.

The trigger is compatible with version 2 gearboxes which are found in the vast majority of M4/AR-15 AEGs. This means that the G&G Armament Trigger For V2 Gearbox trigger should work in practically any M4/AR-15 AEG but will require the gearbox to be opened for installation.

If you have worn out your trigger or you're looking for a milspec trigger to replace a speedyboi flat trigger, this should do the trick! The Krytac Trident Trigger for M4/AR-15 AEG is constructed from alloy and is patterned after the standard curved "Milspec" trigger found on the M4A1 rifle, MK18 MOD.0 and MOD.1 as well as practically any other M4/AR-15 used in military service in the real world.

The trigger is designed for the version 2 gearbox found in the vast majority of M4/AR-15 AEGs, meaning this trigger should work in practically any M4/AR-15 AEG but will require the gearbox to be opened up to install it. 

The Airtech Studios RetroArms Rotary Centring Unit is an easy upgrade to improve your AEG's accuracy. It is constructed from high-density polymer and fits a RetroArms CNC Rotary HOP-Up Chamber Gen.2 ONLY. It prevents the hop-up unit from wobbling side to side. Once fitted, the RetroArms Rotary HOP-Up Chamber will be securely fitted in place and sit in its true centre position, which prevents BBs from swerving at a tangent when shot.

As well as removing the wobbling from your HOP-up chamber, it also provides a better air seal due to the improved tightness of the system, resulting in a more stable FPS output from your AEG. While the power upgrades for shooting BBs further are significant, they wouldn't be effective without accuracy. It's often that small parts like this are overlooked in Airsoft upgrades but they have a major impact and the Airtech Studios RetroArms Rotary Centring Unit is exactly that.

Improve the consistency and accuracy of your RetroArms CNC Rotary HOP-Up Chamber Gen.2 with a simple polymer part, the improvement will be instantly noticeable!

Increase the power and air efficiency of your A&K M249 Series AEG with an upgraded nozzle and O-ring. With its CNC Aluminium Ergal construction and smooth anodized finish, this will drastically improve your AEG's performance compared to the standard polymer nozzle included with the A&K M249 AEG.

The included O-rings provide a far superior air seal. For the best results, make sure to use pure silicone oil to lubricate your cylinder head's nozzle stem before installing this nozzle.

If you want glowing BBs without making your primary any longer or fitting some bulky, slightly ugly, tracer unit, the CYMA Tracer HOP-Up Chamber for AK AEGs is a great choice! This alloy rotary HOP-up chamber integrates a tracer module, just like more expensive alternatives with the option to use red or green tracer BBs. The set includes everything you need to complete the HOP-up chamber build, including the bucking and nub.

This unit is powered by your AEG's battery through the balance cable, meaning it will only work with LiPo batteries unless you have something home-brewed in mind. The set includes 3 sets of wiring for use with 7.4V LiPo, 11.1V LiPo or custom battery solutions, all of which connect to the pre-wired connector on the HOP-up unit itself.

While it is designed for use with the CM series of AKs, this unit should work with most AKs on the market, however, potential modifications will be required to fit certain brands. Depending on your specific platform, fitting may also require modification to your receiver. As such, we only recommend this unit for those who are comfortable working on AEG internals. If this sounds like you, why not shave off length and weight from your classic Russian primary with the CYMA Tracer HOP-Up Chamber for AK AEGs!

Ideal for reviving worn out RIFs or as a backup for a rainy day, this is a complete and assembled gearbox including motor, that is ready to drop into any compatible Version 2 accepting replica.

If you are looking to further extend your advantage and push your AEG to the limits reinforced gears are a must for long term reliability under increased stress. This Laylax EG Hard Gear Set is specifically designed for Airsoft AEGs with a version 2 or version 3 gearbox, or compatibility with v2/3 gearsets and includes a hardened steel spur gear, sector gear and bevel gear. This gearset is a high speed set with a ratio of 16:1, intended to provide a slight speed increase with the same motor compared to the standard 18:1 gears in most AEGs.

A drop-in trigger, ETU & MOSFET for Version 2 compatible rear-wired Airsoft replicas, which includes features like a programmable trigger, low battery cutoff, shot sensor and comes included with a vertical 'speed trigger'.

If you need a new nozzle for your CYMA CM.057 or Real Sword Dragonov SVD, CYMA has you covered! The Aluminium Nozzle for CYMA/Real Sword SVD/SVU is constructed from CNC machined aluminium and compatible with the CYMA CM.057 SVD/SVU AEG series and the Real Sword Dragunov SVD AEG.

This is a replacement original part specifically designed for the Real Sword pattern SVD gearbox used in the CYMA CM.057 series and is not compatible with A&K SVDs or others. If you've built a beast of a DMR with your SVD and you want to get ahead of any potential parts failures this is a great part to have in the toolbox!

If you're looking for a strong and lightweight nozzle for your Airsoft AEG, this is worth a look! The FGATE CNC POM Sealed Nozzle with O-Ring for Airsoft AEGS is made from CNC POM polymer, a massive upgrade from the factory polymer nozzles present in most Airsoft platforms. The nozzle also includes an internal O-ring to maximise air seal, and its ultra-strong POM construction is ideal for high rates of fire or high FPS setups.

You can get a nozzle that is perfectly sized for the majority of Airsoft AEGs, including AKs, M4/M16 and SR25 rifles. So if you want to up your platform's consistency or you're looking for a replacement part, this is a great piece to pick up!

If you're looking for a strong and lightweight nozzle for your Airsoft AEG, this is worth a look! The FGATE CNC POM Sealed Nozzle with O-Ring for Airsoft AEGS is made from CNC POM polymer, a massive upgrade from the factory polymer nozzles present in most Airsoft platforms. The nozzle also includes an internal O-ring to maximise air seal, and its ultra-strong POM construction is ideal for high rates of fire or high FPS setups.

You can get a nozzle that is perfectly sized for the majority of Airsoft AEGs, including AKs, M4/M16 and SR25 rifles. So if you want to up your platform's consistency or you're looking for a replacement part, this is a great piece to pick up!

A replacement pin for your M4 trigger unit, should you need a fresh one. The pin is constructed from steel and measures 2.8cm in length.

A replacement original KRYTAC part which fits version 2, 3, 6 and 7 gearboxes. This cylinder is a Type 1, meaning it has a port in the side intended to reduce the air volume for use on short barrelled platforms (<363mm inner barrel) and prevent the "suck back" phenomenon.

If you need a new cylinder head to fix up your Dragunov, check this out! The CYMA Aluminium Cylinder Head for CYMA/Real Sword SVD/SVU is constructed from CNC machined aluminium and is fitted with two O-rings to seal any gaps between it and the cylinder for perfect efficiency and minimal air loss.

The cylinder head also has a sound dampening pad installed on the rear face which reduces gearbox noise and protects the piston head from the force of repeated impacts. A replacement original part for the CYMA CM.057 SVD/SVU series, this cylinder head is also compatible with the old Real Sword Dragunov SVD!

A Generation 3 Micro Computer Controller Chip Set designed to add a huge variety of functionality to Airsoft AEG. The chip is built to be as compact as possible, requiring the smallest amount space and is specially coated to the Military Specification (Mil-Spec) MIL-V-173C. 

A complete unit to fit into any Airsoft AEG no matter what version gearbox you own. Included is everything from MOSFET to wiring, connectors and programming card.

An efficient and well-constructed Air Nozzle which is available for a wide range of replicas, and ensures improved durability and smooth operation.

If you want to ramp up your semi-auto speed and you run a G&G, you need this! The Airtech Studios STC™ Speed Trigger Converter for G&G AEGs is designed to reduce trigger travel to a hair, allowing you to seriously spam semi in the most efficient way possible.

The STC is designed to fit a wide range of G&G AEGs (full compatibility list on Airtech Studios Website) and makes use of your original trigger, reducing trigger travel by 80%! This set will require opening the gearbox to install so we don't recommend it for newcomers. If you're a CQB player needing an edge, this will do it!

Upgrade your M4/M16 AEG with an FPS Softair Stainless Steel Cylinder and increase its reliability and performance. The cylinder is extremely durable and is more resistant to the constant friction caused by the piston head. The cylinder is made for use with version 2 or 3 gearboxes, compatible with Tokyo Marui derived designs and clones, with barrel lengths of 401mm to 450mm.

If you are looking for an upgraded motor for improved trigger response, or something capable of pulling heavier springs, this will do the trick! This motor from Krytac is a high performance motor setup with a steel pinion gear pre-installed.

The motor is available in either the 20K performance or 30K high torque versions, giving you an option for any build and one for high performance DMR platforms, depending on your build objectives. The motor comes with connections for spade connectors and includes the motor height spring. This motor is a long shaft type, which fits M4/AR15 AEGs and SMG-5 replicas, but not the PDW or K models.

If you are looking for an easy way to make your Airsoft platform exclusively a DMR or CQB beast, this is worth checking out! The Delta Armory Programmable ETU Processor Unit for V2 Gearbox; Semi Only replaces your conventional trigger assembly and offers semi-automatic fire only with adjustable pre-cocking, which can be programmed in using the fire controls of the AEG itself. 

This ETU should fit most M4/AR-15s which use a version 2 gearbox, but we only recommend this part for experienced techs and those in the know when it comes to Airsoft internal upgrades. The ETU is also pre-wired to a Deans/T-Plug battery connector in rear wired configuration and spade connectors for your motor, so you shouldn't need your soldering iron!

If you're working on a beast of a build bristling with all the best parts out there, this is the motor you need to finish it off! The Gate G5 Smart Brushless Motor combines brushless motor technology with a programmable ESC module, allowing you to adjust the motor revolution rate between 10K RPM right up to an insane 46K RPM!

The advantages of running a brushless motor are numerous, the most important of which is a far higher torque-to-weight ratio than conventional motors. The lack of brushes means there is less to go wrong, and the motor is far quieter when running, guaranteeing a longer lifespan of smooth running performance. Another brushless motor perk is their ultra-low heat build-up, ensuring you get let rip with long, lavish bursts guilt-free!

While a brushless motor really is a game-changer once installed, we only recommend adding one to your build if you're confident working on Airsoft internals and are ready to reinforce the right parts to keep it running. If you're the techy type and want to keep your primary at the cutting edge of Airsoft performance, the Gate G5 Smart Brushless Motor belongs inside!