- 7.4V 2S Block battery
- 20C Discharge rate
- 2300mAh capacity
Those of you looking for a battery with a large capacity in a medium-sized block form factor, you've come to the right place! The battery is perfect for larger areas such as full-stocked SMG-5, G3, M16 and AK platforms, AR36 handguards and full-stock rifles. The battery has a voltage of 7.4v, a capacity of 2300mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.
The battery measures 10x1.5x3.4cm with a cable length of roughly 10cm.
- 1550mAh
- 20c Rating
- 7.4v 2S LiPo
Suitable not only for Airsoft but for RC vehicles and toys too, this 7.4v 2200mAh LiPo Stick Battery will fit in tight areas like stock tubes and handguards where other batteries wouldn't normally.
- 7.4V 2S Stick battery
- 25C Discharge rate
- 1500mAh Capacity
If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Gen's Ace 7.4v 1500mAh 25C LiPo Stick Battery measures approximately 12x1.5x1.6cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Mini-Tamiya connector and the length of wire between the cell group and the connector is approximately 6cm.
The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!
- 11.1v LiPo
- 2600mAh Capacity
- 3 x Individual Cells
An absolutely massive 11.1v LiPo 2600mAh 20c LiPo Battery in a Crane Stock configuration, with three cells which have individual dimensions of: 13.1cm x 1.98cm x 1.13cm. It has a 9cm cable with a Deans Connector on the end.
- 1600mAh
- Block Battery
- 11.1v 20C LiPo
An Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries.
- 7.4V 2S Stick battery
- 25C Discharge rate
- 1200mAh Capacity
If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Gen's Ace 7.4v 1200mAh 25C LiPo Stick Battery measures approximately 13x1x2cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Deans connector and the length of wire between the cell group and the connector is approximately 6cm.
The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!
- 2600mAh
- 11.1v 3S LiPo
- Crane Battery
An 11.1v crane stock LiPo Battery with an impressive 2600mAh capacity, designed to ensure that your Airsoft AEG can survive a whole day of Skirmishing.
- 1300mAh
- 25c Rating
- 7.4v 2S LiPo
Giant Power are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.
The battery's dimensions are 10x1.2x3cm with a cable length of roughly 10cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.
- 7.4V 2S Block battery
- 20C Discharge rate
- 1800mAh Capacity
If you need a battery for a fixed stock or other large battery compartments this one should fit the bill! The 7.4V 1800mAh 20C Block LiPo Battery from Electro River is the perfect battery for full stocks found on M16, AK, SMG-5 and G3 Airsoft AEGs. The battery measures 10 x 1.2 x 3.5cm approximately with a wire length of around 9cm and is pre-wired to a mini-Tamiya battery connector.
The battery is a 7.4V 2-cell battery in block configuration with a continuous discharge rate of 20C and a maximum discharge rate of 40C, making it great for almost any Airsoft AEG, though make sure you measure before ordering!
- 2200mAh
- Crane Battery
- 11.1v 15C LiPo
An Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries.
- 7.4V 2S Butterfly battery
- 30C Discharge rate
- 850mAh capacity
Those of you with limited battery space, this block battery is the one! The battery will fit near enough all AEG rifles and will be especially useful in rifles with PDW stocks. It has a voltage of 7.4v, a capacity of 2800mAh and a discharge 30C. The battery is connected to your AEG via the Deans connector, not to be confused with Mini-Tamiya connector, however, adaptors are available.
The battery measures 7.5x1.5x2.5cm with a cable length of roughly 4cm.
- 7.4V 2S Block Battery
- 20C Discharge rate
- 1500mAh Capacity
If you need a compact block battery for a handguard or fixed stock with limited space this should do the trick! The 7.4V 1500mAh 20C LiPo Block Battery from Electro River measures 8.5 x 1.2 x 3.4cm approximately with a wire length between the cell group and connector of approximately 9cm.
The pre-wired connector is the Deans/T-plug the continuous discharge rate is 20C and the maximum is 40C, making this battery great for both Airsoft applications and electronics hobbies.
- 7.4V 2S Crane battery
- 20C Discharge rate
- 2200mAh Capacity
If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.
Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!
- 7.4V 2S Butterfly battery
- 25C Discharge rate
- 2800mAh capacity
Those of you looking for a battery with a truly large capacity, you've come to the right place! The battery is perfect for larger battery compartments such as SMG-5, G3, M16 and AK platforms with fixed stock battery compartments. The battery has a voltage of 7.4v, a capacity of 2800mAh and a continuous discharge rate of 25C with a maximum discharge rate of 50C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.
The battery measures 13x1.1x4.2cm with a cable length of roughly 10cm.
- 7.4V 2S Stick battery
- 15C Discharge rate
- 2000mAh Capacity
If you want the biggest stick battery you can squeeze into your M4/AR-15 buffer tube, this is probably it! The Specna Arms 7.4v 2000mAh 15/30c LiPo Stick Battery is pre-wired to a mini-Tamiya battery connector and designed for slim and long battery compartments. The battery is a 7.4V LiPo with a capacity of 2000mAh, continuous discharge rate of 15C and maximum discharge rate of 30C.
The battery measures 12.3 x 1.6 x 1.8cm approximately and should fit into most M4/AR-15 buffer tubes, though some with less space inside may require that you leave the stock in an extended position. The wire between the cell group and connector is approximately 10cm, giving you plenty of flexibility to fit the battery where you need it. As always, measure up before you buy!
- 1300mAh
- 35C Rating
- 7.4v 2S LiPo
Giant Power are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 35C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.
The battery's dimensions are 7x1.5x3.4cm with a cable length of roughly 7.5cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.
- 1200mAh
- 20C Rating
- 11.1v 3S LiPo
A high quality 11.1V LiPo battery with a 1200mAh capacity and Dean connector, suitable for both Airsoft, RC and more.
- 7.4v 2S
- 1200mAh
- 30C Rating
An ultra thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 30c. Being short and wide, this battery is perfect for PEQ boxes and solid stocks.
- 1600mAh
- 20c Rating
- 7.4v 2S LiPo
A LiPo saddle battery designed to fit in handguards in replacement of the traditional 1600mAh NiMH blocks/saddles (G36 handguards etc).
- 2600mAh
- 20c Rating
- 11.1v 3S LiPo
A large 11.1v VP Racing 2600mAh LiPo with a small Tamiya connector designed for a full days Airsoft action with impressive rate of fire and single shot results.
- 7.4V 2S Flat Nunchuck
- 20C Discharge rate
- 1800mAh Capacity
If you need a battery for your AR36 AEG or polymer handguard equipped M4/AR-15 AEG this one will do the trick! The 7.4v 1800mAh 20C LiPo Flat Nunchuck Battery from Electro River is a flat nunchuck style battery, also known as a "butterfly" configuration. Unlike other nunchuck batteries, this won't inside a crane stock and is more suitable for large polymer handguards such as those found on AR36 and M4A1 AEGs and will also fit nicely in most fixed rifle stocks.
The battery itself is a 2-cell 7.4V LiPo with a wire length of approximately 9cm between the cell groups and the connector, and each of the two cell groups measures 10 x 0.6 x 3.5cm approximately. The pre-wired connector is the common mini-Tamiya type and the continuous discharge rate is 20C, with a maximum discharge rate of 40C.
- 7.4V 2S PEQ Battery
- 30C Discharge rate
- 1000mAh Capacity
If you run a front-wired AEG with limited battery space, storing your battery in a PEQ-15 battery box could be the solution! This 7.4v 1000mAh 30C LiPo battery from Electro River is designed to fit into cramped spaces and is the perfect size for use in a PEQ-15 battery box. The battery measures 6.4 x 1.2 x 3.3cm approximately and the wire length between the cell group and connector is approximately 9.5cm.
The compact size of this battery makes it great for both Airsoft and any other electronics projects you have on the go, providing plenty of juice in a smaller form factor. The continuous discharge rate of this battery is 30C and its peak is 60C, giving you a nice snappy response without overdoing things!
- 1300 mAh
- 7.4V 2S LiPo
- 25C Discharge rating
This LiPo battery from Gens Ace is designed to fit into flat and long battery compartments, such as those found inside the handguards of an AR36 or SMG-5. The battery connects to your AEG via a Deans connector (aka a T-Plug) and provides 1300mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.
- 1400 mAh
- 7.4V 2S LiPo
- 25C Discharge rating
This LiPo battery from Gens Ace is designed to fit into compact and slim battery compartments, such as the M4/AR15 buffer tube and the AK47/74 top cover. The battery connects to your AEG via a Deans connector (AKA T-Plug) and provides 1400mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8.5cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.
- 7.4V 2S Stick Battery
- 15C Discharge rate
- 2000mAh Capacity
If you are looking for the biggest battery you can fit in an M4/AR-15 buffer tube this would be it! The 7.4v 2000mAh 15C LiPo Stick Battery from Electro River just about fits in an M4/AR-15 buffer tube, though we recommend you do not fully collapse the stock once it is installed.
The battery measures 12.6 x1.6 x 2cm and should also be suitable for top-wired AK AEGs and will fit in almost all fixed stock battery compartments regardless of the platform. The wire length between the connector and cell group is approximately 9cm and the continuous discharge rate is 15C with a peak discharge rate of 30C.
- 7.4v 2S
- 1000mAh
- 20C Rating
A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.
- 1200mAh
- 20C Rating
- 11.1v 3S LiPo
A high quality 11.1V LiPo battery with a 1200mAh capacity, suitable for both Airsoft and RC use.
- 1300 mAh
- 7.4V 2S LiPo
- 25C Discharge rating
This LiPo battery from Gens Ace is designed to fit into flat and long battery compartments, such as those found inside the handguards of an AR36 or SMG-5. The battery connects to your AEG via a mini-Tamiya connector and provides 1300mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.
- 7.4V 2S Butterfly battery
- 20C Discharge rate
- 1500mAh capacity
This battery features a wider and flatter butterfly style configuration and while it won't fit in crane stocks it is perfect for larger areas such as AR36 handguards and full stock rifles. The battery has a voltage of 7.4v, a capacity of 1500mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however adaptors are available.
The battery consists of two cells working in tandem with each other, with each cell measuring 8.5x0.6x3.4cm with a cable length of roughly 9cm.
- 1300mAh
- 7.4v 2S LiPo
- Crane Battery
A Standard powered Airsoft Battery, designed to be used in almost all Airsoft AEG weapons with a mini-Tamiya connector, providing the perfect amount of power for most Airsoft Weapons.
About Our Airsoft LiPo Batteries
Shop high quality airsoft LiPo batteries and battery packs for your AEG with Patrol Base.
Offering high voltages that are great for upgraded Airsoft guns, get that rate of fire you’ve been chasing with LiPo batteries offering up to 11.1V. However, for standard replicas or for beginner players, we’d always recommend starting with something smaller, such as a 7.4V.
Our LiPo batteries come in all shapes and sizes, so you’ll be able to find compact styles that take up less space but still offer plenty of hours of gameplay.
Now that you’ve got your LiPo airsoft battery sorted, you’re going to need a charger to go with it. Luckily for you, we’ve got you covered with LiPo chargers that offer auto-stop.
Pick up your new LiPo battery today and enjoy next day delivery, or keep browsing and explore our entire airsoft battery collection, including NiMh airsoft batteries and more.