Airsoft Mounts

A KeyMod attachment for KeyMod Rails which provides a Quick Detach Sling Loop Mounting Point, making it easy to quickly add and remove slings from your rifle.

If you're rocking the AAP-01 or AAP-01C and need a red dot sight to finish it off, the Action Army RMR Plate & Raised Sights Set for AAP-01 is the key. This set includes a raised front sight with a light-enhancing insert and a fixed rear sight with an integral RMR footprint mount plate, allowing you to mount a micro red dot sight for improved low-light accuracy and faster target acquisition!

Both the front sight and the rear sight/mount plate are constructed from steel, making them extremely robust and ideal for the aggressive skirmisher. This kit fits both the original AAP-01 Assassin and AAP-01C Shinobi but isn't compatible with the Action Army Folding Stock Kit. If you run your AAP-01 as a sidearm but need to get on target faster, pair the Action Army RMR Plate & Raised Sights Set for AAP-01 with an RMR footprint red dot sight and get busy!

If you need a bit more height on your optic for a clear view with full face protection, the Delta Armory 3-Slot 20mm Picatinny Riser Mount for Red Dot Sights will do the trick. This riser mount provides a 3-slot 20mm Picatinny rail approximately 1 inch (25mm) above the surface of the rail it is mounted to, raising the optic to M4/AR-15 height over bore. This means it will align perfectly with an M4/AR-15 front sight post and most flip-up iron sights; ideal for those who like to "co-witness" their optic and irons. 

If you find you have to bend your neck to get a good view down your red dot sight, a riser is what you need. This riser can be mounted to any 20mm Picatinny railed receiver and is ideal for small "micro red dot sights" like the T1/2 and Docter/RMR style red dot sights due to its compact size.

The Delta Armory 22mm Offset Angled Mount has an aluminium alloy construction, making it tough and lightweight. It is designed to install Torches, Lasers and other 20mm RIS Accessories at a 45-degree angle, which allows you to maximise the available space you have on your Airsoft Gun.

An advantage of this mounting method is that it makes your device easier to reach and use, as well as limiting obstruction to other accessories. Although designed for torches, this rail could also be used to mount an offset Red Dot Sight to use as a backup to your main sight. The Delta Armory 22mm Offset Angled Mount easily attaches to 20mm Rails via the Allen Screw on the side of the unit.

If you have QD sling sockets on your Airsoft rifle it would be rude not to take pure advantage and set your rifle up with a highly flexible sling setup which can be installed, altered and removed in mere seconds! This QD sling swivel from CYMA fits any QD sling socket and provides a wide "loop" style mount, to which a sling of practically any style can be mounted. To install the swivel onto a QD socket, simply push it into the socket and it will automatically lock in place. To disconnect the swivel all you need to do is press the button in the centre which will release the retention and disconnect the swivel from the socket on the rifle. This QD swivel can be rotated to any angle, guaranteeing the utmost comfort no matter which sling style you choose!

The UNITY mounts are being favoured world wide due to their slim profile & efficient riser, making them an excellent candidate for using with PEQ / Laser pointers mounted on the upper rail.

The UNITY mounts are being favoured world wide due to their slim profile & efficient riser, making them an excellent candidate for using with PEQ / Laser pointers mounted on the upper rail.

Those of you wanting to mount an optic or torch closer to your handguard without mounting to the handguard itself, you have found your answer.

Attached to M-LOK system, the mount is offset by 45 degrees, meaning the rail is closer to the barrel, and gives you additional flexibility on where you want your rail and subsequent light/optics etc. mounting. This mount is unique in that a scout flashlight can be mounted directly to the mount using screws thus saving you a bit of weight and space. Of course other devices can be mounted using the Picatinny rail.

The rail is a 20mm Picatinny type, measuring roughly 1.25 inches and is attached to M-LOK system using the included screws, nuts and Allen key. Featuring aluminium alloy construction, the mount is both tough and lightweight, which will complement any loadout.

If you are rocking the Novritsch SSP5 GBB pistol that thing isn't complete without a red dot sight! The Novritsch Premium Red Dot Plate for SSP5 GBB pistol is designed specifically for the SSP5 series and is constructed from CNC machined aluminium with an anodised finish. This red dot plate uses the Docter red dot sight footprint and should fit any micro red dot sight with the Docter footprint, including the Novritsch Red Dot Sight Premium V3. If you want to take pure advantage of the borderline insane performance of the SSP5 at long range, this plate is the key!

If you're looking for an M-LOK QD sling socket which is ergonomically designed and won't contort your sling, the PTS Syndicate EP M-LOK QD Sling Mount is a fantastic choice. Designed as an alternative to built-in QD sling sockets and standard flat sockets, when installed, this socket faces the shooter, resulting in a more comfortable sling position and less chance of tangles.

Constructed from high-density polymer with a steel QD cup, this socket should be compatible with most QD sling swivels on the market, allowing you to install or disconnect your sling quickly. Due to differences in tolerance between manufacturers, we suggest thoroughly testing this socket before entrusting it with any weight unless you're using it with a PTS-branded QD swivel. If you find the built-in QD sockets on your handguard are positioned suboptimally or don't have any QD sockets on your M-LOK handguard, the PTS Syndicate EP M-LOK QD Sling Mount is a fantastic choice!

If you're looking for an M-LOK QD sling socket which is ergonomically designed and won't contort your sling, the PTS Syndicate EP M-LOK QD Sling Mount is a fantastic choice. Designed as an alternative to built-in QD sling sockets and standard flat sockets, when installed, this socket faces the shooter, resulting in a more comfortable sling position and less chance of tangles.

Constructed from high-density polymer with a steel QD cup, this socket should be compatible with most QD sling swivels on the market, allowing you to install or disconnect your sling quickly. Due to differences in tolerance between manufacturers, we suggest thoroughly testing this socket before entrusting it with any weight unless you're using it with a PTS-branded QD swivel. If you find the built-in QD sockets on your handguard are positioned suboptimally or don't have any QD sockets on your M-LOK handguard, the PTS Syndicate EP M-LOK QD Sling Mount is a fantastic choice!

If you're searching for a sling mounting solution for your M4/AR-15 AEG, the Delta Armory CQD Sling Plate for M4/AR-15 AEG is ideal. Constructed from steel for maximum strength, this CQD-style sling plate allows you to mount a single-point sling to either side of your sliding stock M4/AR-15 AEG, ideal for left or right-handed shooters. The plate can also be paired with a front sling point if you prefer a two-point sling. Compatibility-wise, this plate should fit any Marui-spec M4/AR-15 AEG with a sliding stock but won't work with fixed stocks or PDW stocks.

If you have ever missed a kill because you had to pull off target to adjust magnification, this mount was designed with you in mind! The Ghost Quick Zoom Sliding Scope Adjuster for 20mm Picatinny Rail allows you to adjust the magnification of any adjustable mag riflescope with a rotary adjuster from a firing grip while you keep your reticle on target! Gone are the days of awkward body mechanics when adjusting your optic, giving you more opportunity to bag those all important kills in game!

The Quick Zoom Sliding Scope Adjuster is constructed almost entirely from CNC machined aluminium with steel cables and a polymer sliding button and can be fitted to any Airsoft rifle with a minimum top rail length of approximately 38cm. A spacer is included for longer setups, keeping the adjustment cables protected from snags, and also included in the box is an upper scope ring segment with a 20mm Picatinny rail built-in, allowing a micro red dot sight to be added to the setup as a backup. This combination of a dual ring scope mount, sliding button, spacer and an MRDS mount gives you a whole lot of alu for your money, and even more skirmish utility!

If you are having a hard time seeing down your low-profile red dot sight, this rail riser will make all the difference! The PJ 0.83" Mini Riser Block Mount is designed to assist those who struggle to see down their red dot sight, either because of a very low profile mount, a full face mask or neck pain.

The riser offers a 4cm length of 20mm Picatinny rail raised 0.83"/2.2cm above the height of the original rail to which it is mounted. Being constructed from aluminium with a steel mounting bolt, this riser keeps added weight to an absolute minimum. Mounting the riser is as simple as mounting your red dot; simply align it with your rail and tighten down the thumb screw on the side.

If you are having a hard time getting your face low enough to see through your optic, this riser should solve that issue and get you shooting straight

If you've been working with an improvised sling solution for your VMP-1, time to get professional! The VORSK Sling Plate for VMP-1 GBB SMGs is constructed from steel, mounting between the stock and receiver at the ideal spot for a single-point sling. The plate includes a keyring extension for more flexibility but this can be removed entirely if not needed or replaced with a loop of paracord for a stealthier alternative. 

When installed, the sling loop is centrally positioned below the stock, granting it ambidextrous functionality, great for left or right-handed shooters. Its steel construction guarantees it can take the weight of whatever you've mounted to your VMP-1, giving you a sling solution which is both reliable and looks professional. Compatibility-wise, this plate will work with both the original VMP-1 and VMP-1X but isn't compatible with the VMP-1C. 

These scope rings are designed to hold an Airsoft rifle scope with a tube diameter of 30mm. Scope rings are useful as they allow you to attach your scope to very small sections of Picatinny rail, such as the small sections often found on sniper rifles. These mounts are High Profile, which means they will hold your Optic a little higher than standard, which is ideal for those who use Lower Face Protection and struggle to aim down their Scope. 

Being a two-piece design they are very easy to install. The scope rings mount to standard Picatinny rail sections, often found atop your Airsoft platform. To secure your rifle scope, you must use an Allen key to take off the top sections of the rings, then place your scope in and reattach the top sections of the rings. 

The WADSN 5 Position Flashlight Mount is a great way to attach your flashlight to your platforms. It mounts to a 20mm RIS/RAS rail, which is the most common rail found on rifles and SMGs. There is a choice of black or dark earth so you can match the mount perfectly to fit the style of your loadout. It features 5 adjustable positions so you can find the perfect setup for your loadout and ensure you dominate any CQB skirmish!

To fit your flashlight you must first loosen the two screws found at the front and back of this mount, once loose, you can slide your torch in. Afterwards, tighten the screws up again and your flashlight and mount are ready to go! The polymer construction means you don't need to worry about having a front-heavy Airsoft gun once fitted. Mount your flashlight using the WADSN 5 Position Flashlight Mount and become a master of close-quarters surprise engagements!

If you're in search of a sling solution which easy to mount and remove, the Vector Optics QD Sling Socket & Swivel for 20mm Picatinny Rails is ideal. This set includes a QD sling socket for 20mm Picatinny rails and a QD sling swivel, allowing you to quickly remove your sling without the usual detangling process. The included swivel should fit most slings on the market and is constructed from steel for maximum strength. 

To release the swivel from the socket, simply press the central button and it will pop straight out. Remounting it is as simple as pushing the swivel back into the socket where it will lock in place. The socket should also be compatible with aftermarket QD swivels but due to differing specs between manufacturers, we always advise giving the swivel a thorough test before entrusting it with the weight of your platform. 

The UNITY Tactical mounts are being favoured worldwide due to their slim profile & efficient elevation, making them an excellent candidate for use with PEQ / Laser pointers mounted on the upper rail or for bringing your optic over your irons.

The UNITY Tactical mounts are being favoured worldwide due to their slim profile & efficient elevation, making them an excellent candidate for use with PEQ / Laser pointers mounted on the upper rail or for bringing your optic over your irons.

If you want to take pure advantage of the SSP5's incredible range and accuracy, an optics mount will get you there! The Novritsch 20mm Picatinny Top Rail for SSP5 GBB Pistol is compatible with all variants of the SSP5 GBB and is constructed from CNC machined aluminium for a perfect combination of low weight, high strength and flawlessly in-spec rail dimensions.

The Top Rail is available in two different lengths, a short version measuring approximately 6cm long and a longer version measuring approximately 10.1 cm. The rail is installed on the optics mount section of the fixed SSP5 outer barrel, meaning it says put while you tap tap tap that trigger for easier target acquisition and less chance your optic will take damage from recoil. If you are running your SSP5 as a primary, this mount is essential to make the most of its epic performance!

If you're following modern real steel trends and want a red dot on your sidearm, Airsoft Artisan has what you need! The RMR Mount w/ Front & Rear Sight for WE EU17 GBB includes a front and rear sight with an integral RMR footprint mount plate, allowing you to rock an RMR-style red dot sight paired with a cutting-edge iron sight setup on your WE EU series GBB pistol. 

The front sight includes a red light-enhancing insert and the rear sight features anti-glare checkering, giving you an up-to-date sight setup which is great in both bright and dark conditions. The sights are also set at "suppressor height", meaning if you've got a sneaky build planned or are running a tracer you can still get a clean sight picture. 

The plate itself is designed for RMR footprint red dot sights, meaning most RMR clones should fit including our PCS Miniature Red Dot Reflex Sight. This set is designed for the WE EU17 GBB and as such should also fit WE EU19 and EU34 GBB pistols but won't fit WE EU18 GBB pistols due to their redesigned slide. If your EU series needs a touch of modernity, the Airsoft Artisan RMR Mount w/ Front & Rear Sight for WE EU17 GBB will provide!

A Sling Plate designed to fit on M4 Style Airsoft 6mm BB Guns, fitting on AEG Electric Rifles between the Receiver and the Buffer tube allowing the attachment of Slings.

If you're in need of an RMR mounting plate for your Army Armament STACCATO pistol, then you've come to the right place! This plate is the perfect accessory for those wanting to mount a red dot sight to their pistol for some extra accuracy whilst out on the battlefield. It is constructed from aluminium and comes with the necessary steel mounting screws to attach this plate to your pistol.

It is compatible with red dot sights that have an RMR footprint, such as the PCS Miniature Red Dot Reflex Sight. If you're looking for a replacement RMR plate, or you need one to mount your desired red dot, the Army Armament Staccato RMR Mounting Plate is perfect for you.

If you like your sidearm equipped with the latest sight setup, you'll need the RMR Mount w/ Front & Rear Sight for Tokyo Marui EU17/26 GBB from Airsoft Artisan. This set includes a front and rear sight with an integral RMR footprint mount plate, allowing you to rock an RMR-style red dot sight paired with a cutting-edge iron sight setup on your Tokyo Marui EU17 or EU26 GBB pistol.

The front sight includes a red light-enhancing insert and the rear sight features anti-glare checkering, giving you an up-to-date sight setup which is great in both bright and dark conditions. The sights are also set at "suppressor height", meaning if you've got a sneaky build planned or are running a tracer you can still get a clean sight picture. 

The plate itself is designed for RMR footprint red dot sights, meaning most RMR clones should fit including our PCS Miniature Red Dot Reflex Sight. Compatibility-wise, this set is designed for the Tokyo Marui EU17 Gen 3 and EU26 GBB pistols but in all likelihood won't fit the newer EU19, EU34 or the full auto EU18. If you need to get on target faster with your handgun, the Airsoft Artisan RMR Mount w/ Front & Rear Sight for Tokyo Marui EU17/26 GBB is what you need!

A Sling Plate designed to fit on M4 Style Airsoft 6mm BB Guns, fitting on GBB Gas Blowback Rifles between the Receiver and the Buffer tube allowing the attachment of Slings. 

One of the few problems with old-school cool like the SMG5K series of AEGs is that you are rather limited in rail mounting space, meaning your mission essential equipment that makes you a true operator has to be left behind. Ask the US Navy SEALs, they are known to use pipe clips and zip ties to attach rails to their MP5SD6s. You no longer have to resort to this pure bodgery, with the Extended top rail mount from CYMA you now have a Picatinny scope mount with forward M-LOK sections for tactical weapon lights, lasers, battery boxes, or anything else you need. This is all kept at the 12 o'clock position, keeping your ambi friendly SMG just that. 

If you're moving away from standard scope rings in favour of something more modern and lightweight, the Novritsch One-Piece 20mm Picatinny Scope Mount; 25mm Tube is ideal. This single-piece scope mount follows modern trends, combining the front and rear scope ring for a more robust combination setup which is easier to mount as a bonus. 

Its aluminium construction keeps the weight of the One-Piece 20mm Picatinny Scope Mount to a minuscule 138 grams and its raised optical centreline means your scope sits slightly higher than usual, ideal for those who like to keep their knashers protected behind a face mask while skirmishing. Each ring also includes a single slot of 20mm Picatinny rail, ideal for micro red dot sights, Runcam/action cameras or whatever other equipment you need to complete the mission at hand!

Compatibility-wise, this mount should fit any LPVO or Rifle Scope with a 25mm monotube but will not fit 30mm monotube optics. If you want a more advanced scope mounting solution for your primary or have trouble looking through your scope due to your face-pro choice, the Novritsch One-Piece 20mm Picatinny Scope Mount; 25mm Tube is what you need!

A combination scope and side rail 20mm RIS rail mount designed to fit on both Airsoft Electric and Gas type AK Platform weapons which feature a side mount plate. 

If you're stuggling to get a good view through your red dot sight when wearing face protection, the WADSN High 20mm Picatinny Mount for T1/T2 Red Dot & PEQ Box will solve that issue! This raised optic mount is patterned after real steel "Hydra" mounts, offering a raised mount for T1/T2 style red dot sights and a 20mm Picatinny rail for a PEQ/DBAL laser unit or scope camera. This mount is designed for 20mm Picatinny rails and includes a pair of "recoil lugs" on the bottom which hold it in place firmly on your rail. 

The High 20mm Picatinny Mount for T1/T2 Red Dot & PEQ Box should fit most T1 and T2 clones provided they correctly replicate the real Aimpoint Micro mounting standard and is also compatible with the Novritsch Red Dot Sight V3, Vector Optics Maverick, Vortex Sparc Solar and Holosun 403B. Being slightly higher than a standard T1 mount, the High 20mm Picatinny Mount for T1/T2 Red Dot & PEQ Box is ideal for those who have a hard time getting a clear sight picture using full face protection, being designed in the real world for use with respirators and night vision devices.