All Airsoft Batteries

An ultra-thin and lightweight battery, perfect for squeezing into even the tightest spots. This battery provides 1200mAh of power with a discharge rate of 30c. Being short and wide, this battery is perfect for PEQ boxes and solid stocks.

If you run a front-wired AEG with limited battery space, storing your battery in a PEQ-15 battery box could be the solution! This 7.4V 850mAh 20C LiPo battery from Electro River is designed to fit into cramped spaces and is the perfect size for use in a PEQ-15 battery box. The battery measures  5.5 x 3 x 1.5cm approximately, and the wire length between the cell group and connector is approximately 11cm.

The compact size of this battery makes it great for both Airsoft and any other electronics projects you have on the go, providing plenty of juice in a smaller form factor. The continuous discharge rate of this battery is 20C, and its peak is 60C, giving you a nice snappy response without overdoing things!

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

If you're after an 8.4V NiMh battery for a crane stock battery compartment, the GFC 8.4V 1600mAh Ni-Mh Crane Stock Battery; Mini Tamiya is ideal. A 7-cell rechargeable NiMh battery pre-wired to a mini-Tamiya battery connector, this Crane configuration battery is ideal for rear-wired M4/AR-15 AEGs with Crane stock battery compartments. Wire length is approximately 10cm, giving you a bit of extra flexibility for easy installation. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

This LiPo battery from Specna Arms is designed to fit into flat and long battery compartments, such as some handguards or crane stocks. The battery connects to your AEG via a Deans connector and provides 2000mAh capacity with a 15C discharge rating.

The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 10.5cm, allowing an easier fit into tighter spaces. The Specna Arms 11.1V 2000mAh 15C LiPo Nunchuck Battery; Deans would be great for any Airsoft gun which requires an 11.1V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

An ideal pack of 4 x AA batteries to power your accessories, from remotes to optics and more.

A singular CR2016 3V Lithium button battery which is commonly used for accessories such as sights and torches/lasers.

A compact yet high output LiPo battery designed for most M4 stock tubes, solid stocks and some hand guards.

A pack of two AG3 LR41 batteries which are perfect for a range of Airsoft accessories and are ideal for keeping spare for Airsoft skirmishes to make sure you aren't taken out of the fight by a dead battery.

If you're after a flat nunchuck, aka butterfly battery for an AR-36 or M4A1 polymer handguard, the Giant Power 11.1v 1500mAh 25C LiPo Flat Nunchuck Battery is ideal. Designed for AR-36 and M4A1 handguards but capable of fitting in various unconventional battery compartments, this LiPo battery measures approximately 9.5cm x 2.9cm x 0.6cm (per cell), with a 5cm wire length, and is pre-wired to a Deans/T-plug battery connector. This battery can also be used in M16A1 or A2 fixed stocks, AK fixed stocks or any other platform with a decently sized fixed stock battery compartment. 

Please note: 11.1V LiPo batteries can cause pre-engagement in AEGs at UK power levels. This can result in internal damage. Please ensure you only use 11.1V batteries in AEGs designed for them (see "Specifications" on our AEG product pages for battery recommendations). 

If you like to be at the cutting edge of battery technology when it comes to Airsoft, you're going to want to check this out! The Gens Ace 7.4V 25C 1000mAh Airsoft LiPo Battery - Mini-Tamiya is a slim LiPo battery intended for Airsoft buffer tube battery compartments, AK top covers and other cramped spaces requiring a single cell group. The discharge rate is 25C, giving you a snappy response without risking overspin in most setups, and the capacity is 1000mAh, meaning you might need two to get through a full game day.

Where this battery differs from the norm is its Smart Balance Connector which interfaces with the Gens Ace IMARS Mini Charger, communicating the battery type and current charge levels and immediately commencing optimal charging as soon as this "Smart Battery" is connected. Compared to legacy smart chargers, this saves loads of time but unfortunately means that this battery cannot be charged using a standard LiPo balance charger.

If you have serious power demands and LiPo batteries don't cut it, Titan Power has you covered with the game-changing 7.4V 3000mAh Li-Ion Stick Battery; Deans Connector! Designed to fit into AR buffer tubes (some may require the stock to be extended), this power-dense Li-Ion battery has innumerable benefits over standard LiPos, including more robust steel-cased cells, larger capacity and no chance of swelling. 

Titan Power Li-Ion batteries can be charged through a standard LiPo balance charger using LiPo settings or with a B6-style smart charger (sometimes known as 4-button smart chargers) using "LiPo Balance" settings. Titan Power advise not charging using "Li-Ion" mode as this is generally intended for higher capacity batteries. 

As always, we recommend using a LiPo Safe Charging Bag for both charging and storage, and never leaving a battery on charge unattended. If you need a battery which will definitely keep your AEG going over long durations, the Titan Power 7.4V 3000mAh Li-Ion Stick Battery; Deans Connector is the best option out there!

A blister pack of 10 x 1.5v Lithium button batteries that are commonly used in Airsoft sights, scopes and other accessories.

If you need a NiMh battery for a top-wired AK or SMG-5K/MP5K AEG, the GFC 9.6V 1600mAh Ni-Mh Stick Battery; Mini Tamiya is the way to go! A battery of 8 cells formed into a single long cell group, this 9.6V rechargeable NiMh battery is a perfect fit in AK AEGs with a battery compartment inside the dust cover or SMG-5K/MP5K AEGs with a battery housed inside the receiver. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

If you need a battery for your top wired AK or SMG-5K AEG and would rather get everything you need in one place, here it is! This bundle includes a LE-3 LiPo Balance Charger, a Safe Charging Bag and a Giant Power 7.4V 1300mAh LiPo Slim Stick Battery with a Mini-Tamiya connector; an ideal setup for a mini-Tamiya equipped top wired AK or SMG-5K AEG with a battery compartment inside the receiver.  

The dimensions of the included battery are as follows: 18.5cm x 1cm x 2cm with approximately 9.5cm of wiring between the battery and connector. 

If you're running an M4 with a crane stock and need a longer-lasting battery, the GFC 9.6V 2200mAh Ni-Mh Nunchuck Battery; Mini Tamiya is a good shout. A battery of 8 cells formed into a single long cell group, this 9.6V rechargeable NiMh battery is a perfect fit for M4 AEGs with a Crane battery stock (or similar battery stock design) and also fits great in AEGs with fixed stock battery compartments (M16, etc.). Please note, to install this battery in a Crane Stock-equipped M4, you will need to place one of the cell groups inside the buffer tube. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

An absolutely massive 11.1v 2000mAh Li-Ion battery in a stick configuration, which allows you to squeeze as much lifespan out of your Airsoft Electric Gun as possible, by offering a lower cost and higher power density vs. LiPo batteries.

An absolutely massive 11.1v 2000mAh Li-Ion battery in a stick configuration, which allows you to squeeze as much lifespan out of your Airsoft Electric Gun as possible, by offering a lower cost and higher power density vs. LiPo batteries.

The perfect battery to give you enough juice for a full weekend of Airsoft milsim action. 9.6v and 4600mAh of power. Commonly used within M249, M16 and M14 variants.

If you're worried your red dot sights batteries are running low, pick up some spares! The AG9 LR936 battery is most commonly seen in Airsoft accessories such as the TA01 ACOG style scope. It comes as a pack of one so make sure you get the correct amount that you need!

This is a Ni-MH AEP battery for Jing Gong V-61 SMG & Jing Gong JG.0452 MAC-10. Due to its shape and size, it may not be compatible with any other AEPs. It has a 7.2V with 750mAh, larger than most typical AEP batteries. If you want to play for longer during an Airsoft Game without having to return to the safe zone, then stock up on spare batteries today.

This tiny Specna Arms 7.4V 1300mAh 30C Micro PEQ LiPo Battery is the best fit for a PEQ box wired gun, such as the Specna Arms SA-H01. It can squeeze into some tight spots, with its dimensions of 6.5x1.5x3.5cm; it will sadly not fit in PDW stocks, but may fit in some SMG and AR36 handguards.

As it is a 7.4V LiPo, it is compatible with almost every Airsoft gun, plus, its Deans-style connector is optimal as most modern Airsoft guns are coming with Deans connectors installed due to its lower electrical resistance when compared with Tamiya connectors. If you need a small battery for your Airsoft platform, the Specna Arms 7.4V 1300mAh 30C Micro PEQ LiPo Battery; Deans could be the best choice for you!

If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Gen's Ace 7.4v 1500mAh 25C LiPo Stick Battery measures approximately 12x1.5x1.6cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Mini-Tamiya connector and the length of wire between the cell group and the connector is approximately 6cm.

The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!

A strip of two LR66 / LR626 batteries of a 1.5V individual voltage, perfect for any accessories that run this strange size of watch battery.

If you need a super-tiny battery for a PDW stock, EMG Autobot Speedloader or other cramped battery compartment, check this out! The Giant Power 7.4v 560mAh 25c LiPo PDW/Autobot Stick Battery measures a mere 7.5cm x 1.1cm x 1.5cm approximately, with 5cm of wire length, pre-wired to a Deans/T-plug battery connector. 

Being super-duper small, this battery will fit neatly where others won't, including in L85 platforms wired to the pistol grip (A3 & AFV), M4/AR-15 platforms with PDW stocks and other tight battery compartments. It's also a perfect fit in EMG's Autobot Speed Loader!

This ultra-thin Specna Arms 7.4V 1000mAh 30C Micro PEQ LiPo Battery is perfect for a PEQ box wired gun, such as the Specna Arms SA-H01. It can squeeze into some tight spots, but with its dimensions of 6.5x1x3.5cm, it will sadly not fit in PDW stocks but may fit in some SMG and AR36 handguards.

As it is a 7.4V LiPo, it is compatible with pretty much every Airsoft gun, and its Deans-style connector is optimal as most modern Airsoft guns are coming with Deans connectors installed due to its lower electrical resistance when compared with Tamiya connectors. If you need a teeny tiny battery for something, the Specna Arms 7.4V 1000mAh 30C Micro PEQ LiPo Battery; Deans could be your best shout!

An 8.4V 1600mAH stick battery with a Mini-Tamiya connector which can be charged using a standard NiMH charger. This battery's stick configuration makes it ideal for folding stock AK type AEGs or others with a long, thin battery compartment.

If you're running a retro AEG and need a battery with a Large Tamiya connector, GFC has you covered! The 9.6V 2200mAh Ni-Mh Nunchuck Battery; Large Tamiya is an 8-cell NiMh battery wired in nunchuck configuration as two cell groups with 5cm of wire length between the cells and the pre-wired Large Tamiya connector. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

Ideal for fixed stock battery compartments but a bit too chonky for crane stocks, this battery is ideal for Cybergun FAMAS replicas or older TM AEGs with Large Tamiya connectors (TM M14, M16A1/A2, FAMAS, etc.). 

A high quality 11.1V LiPo battery with a 1200mAh capacity, suitable for both Airsoft and RC use.

If you're running an upgraded or MOSFET-equipped AEG, this Gens Ace 11.1v 25C 1500mAh LiPo Battery may be just what you need to power it. This Lithium Polymer (LiPo) battery is pre-wired to a Deans/T-Plug battery connector and consists of 3 cell groups wired in nun-chuck/crane/butterfly configuration. The wire length between the cells and connector is approximately 8cm and each of the 3 cells measures approximately 0.8 x 1.6 x 13 cm. 

Not all Airsoft AEGs are capable of running an 11.1V LiPo without causing damage, if you are unsure check the recommended battery section of the your gun's product description. LiPo batteries require balance charging, meaning this battery MUST be charged using a LiPo balance charger with the balance port connected. We recommend using a battery charging bag for storage and charging, and to never leave an Airsoft battery on charge while unattended.