- Pack Of 6
- Fits To Cylinder Head
- May Reduce FPS Slightly
Can be fitted inside other rifles including AEG gearboxes. The sorbo pad works by absorbing impact from your piston head, please note you should expect an FPS loss so you may have to improve the air seal or fit a slightly larger spring to regain your desired FPS.
Fast Delivery
Delivery & Postage
Here at Patrol Base we ship worldwide, delivering not only to the UK but to most of the EU and select Worldwide locations as well. We provide a working day-by-road service via our handpicked courier services, simply buy your Airsoft guns with us and we'll have them delivered directly to your door.
For more information and to see the country we deliver please check out our Delivery Information Page.
Estimates
Below are some rough postage prices for orders. Please note these are subject to change and are only a rough guide. For a more accurate postage estimate please use the Postage Calculator at the basket.
UK Standard
£6.95
Approx.
UK Next Day
£8.95
Approx.
Highlands / Islands
£24.99*
Approx.
Saturday
£14.95
Approx.
* Scottish Highlands, Islands, and EU post prices can vary wildly. Prices range from £8.99 to £29.99, so please ensure you refer to the Postage Calculator at the basket for the lowest possible price.
Returns
We want you to be delighted with our products and services, so we provide the simple Patrol Base guarantee: if on receiving your item you are unhappy with your item for any reason then simply send it back to us. We will replace or refund the item.
You can return any item for any reason whatsoever, even if you have just changed your mind, within 14 days of receipt of the order. This is in addition to your rights under the Consumer Protection (Distance Selling) Regulations 2000.
For more information on returning products, and how to do it please visit our Returns Policy Page.
Description
For those who are looking to create the most silent sniper or AEG out there. Each pack includes 6 pieces in total of sorbo pads with a sticky back for application. These are originally produced for sniper rifles, especially a VSR/Bar-10 platform but can be fitted inside other rifles including AEG gearboxes. The sorbo pad works by absorbing impact from your piston head, please note you should expect an FPS loss so you may have to improve the air seal or fit a slightly larger spring to regain your desired FPS. Feel free to mix and match, you do not have to run both a Blue and Black piece together. Experimenting is key with these components and will only work in AEGS where the cylinder head has a centre hole for air release. The pads are intended to be stuck to your cylinder head, we recomend a flat cylinder head face for best application.
Features:
- Mix and match to create a thicker or thinner padding
- 3M sticky backing
- Easy to fit
- 3mm thick Blue pieces
- 1mm thick Black pieces
- 20mm diametre
- Can be easily shaved/shaped if required
Package Includes:
- 3x Blue thick sorbothane pads
- 3x Black thin sorbothane pads
Special Instructions
Please note that these are designs to stick to your cylinder head, we recommend a flat cylinder head type for best contact. You may need to roughen up the surface and use additional glue to secure parts too.
Specification
General
|
Internal Part Type
|
Cylinder Head
|
|---|---|
 |
Upgrade Parts
Sorbothane Pads
|
Weight and Dimension
 |
Approx. 0.05kg
|
|---|
Construction
 |
Black,
Blue,
|
|---|---|
 |
Durometer Sorbothane
|
|
Internal Part Construction
|
Durometer Sorbothane
|
Part Specific
|
Part for Power Source Type
|
Spring
|
|---|---|
 |
|
|
Package Includes
|
Sorbothane Pads
|
Size guide
Parts Fitting
Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff.
Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.
We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!
Unique Parts
Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.
Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.
If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.
For more information with fitting parts, or should you require help, feel free to get in touch with our Workshop Department via our Contact Us Page.
Terms and Conditions relating to parts fitting can be read on our Terms and Conditions Page.