If you want to give your lid a new look, the PTS Syndicate Velcro Kit for MTEK FLUX Helmet lets you do just that! Designed for the PTS MTEK FLUX but compatible with most other Airsoft helmets, this velcro kit is easy to install thanks to its self-adhesive backing. This kit is available in two variants, interior and exterior.

The exterior version mounts to the outside of your helmet and allows you to kit your brain bucket out with morale and I.D. patches and other velcro-mounted accessories. The interior version makes a great replacement for worn-out interior velcro and can be a great way to rearrange your helmet's interior padding for a more comfortable fit.

If you want to give your lid a new look, the PTS Syndicate Velcro Kit for MTEK FLUX Helmet lets you do just that! Designed for the PTS MTEK FLUX but compatible with most other Airsoft helmets, this velcro kit is easy to install thanks to its self-adhesive backing. This kit is available in two variants, interior and exterior.

The exterior version mounts to the outside of your helmet and allows you to kit your brain bucket out with morale and I.D. patches and other velcro-mounted accessories. The interior version makes a great replacement for worn-out interior velcro and can be a great way to rearrange your helmet's interior padding for a more comfortable fit.

The MEC M-Valve from PTS is designed to improve gas efficiency and speed up the cyclic rate of your Tokyo Marui EU17 GBB pistol. The valve is constructed from high strength brass with rubber O-rings and should help improve the performance of your pistol in cold weather, and speed up the cyclic rate if you have installed a heavy steel slide.

A replacement mock Compensator / Flash Hider for Airsoft 6mm BB Guns, fully licensed by PTS Syndicate, and is a replica based on the Griffin Armament design. 

If you're working on a DMR build or otherwise lengthy platform, the PTS Syndicate Dead Air Sandman-L Tracer version is what you need to top it off! A detailed, licensed replica of the real steel Dead Air Sandman-L, this mock suppressor is pre-fitted with a muzzle flash tracer module and is licensed by Dead Air Silencers. This, of course, means licensed trademarks across the design, ideal for builds which prioritise realism!

Designed to mount to the KeyMo QD interface present on the included steel flash hider (or other PTS KeyMo muzzle devices), the Sandman-L is quick to attach and remove, allowing you to set up in seconds for the scenario ahead and never be fixed to one configuration. The internal tracer module is powered by a rechargeable battery and recharged via a USB Type-C cable, making it convenient and economical to run compared to older tracer designs which use disposable alkaline batteries.

The Sandman-L is the longest of the Sandman suppressor line, ideal for DMRs and other long platforms seeking the stealthy aesthetic. If you're working on an ultra-modern build and need a suppressor which makes others feel inadequate, the PTS Syndicate Dead Air Sandman-L Tracer version will do just that!

If you're working on a DMR build or otherwise lengthy platform, the PTS Syndicate Dead Air Sandman-L Tracer version is what you need to top it off! A detailed, licensed replica of the real steel Dead Air Sandman-L, this mock suppressor is pre-fitted with a muzzle flash tracer module and is licensed by Dead Air Silencers. This, of course, means licensed trademarks across the design, ideal for builds which prioritise realism!

Designed to mount to the KeyMo QD interface present on the included steel flash hider (or other PTS KeyMo muzzle devices), the Sandman-L is quick to attach and remove, allowing you to set up in seconds for the scenario ahead and never be fixed to one configuration. The internal tracer module is powered by a rechargeable battery and recharged via a USB Type-C cable, making it convenient and economical to run compared to older tracer designs which use disposable alkaline batteries.

The Sandman-L is the longest of the Sandman suppressor line, ideal for DMRs and other long platforms seeking the stealthy aesthetic. If you're working on an ultra-modern build and need a suppressor which makes others feel inadequate, the PTS Syndicate Dead Air Sandman-L Tracer version will do just that!

If you're running a laser or flashlight with a 2.5mm jack, the PTS Syndicate Unity Tactical AXON-SL Pressure Switch; 2.5mm Plug will make your setup that bit slicker! Designed to mount to 20mm Picatinny rails and take up as little space as possible, the AXON-SL is perfect for compact platforms with little rail space to spare, measuring a mere 4cm end to end.

The set includes a silver 2.5mm plug and a gold 2.5mm plug, both of which are compatible with other plugs in the PTS Unity ecosystem. The switch itself is a single-button switch but can be operated in both momentary-on and constant-on modes. Simply half-press the switch for momentary-on and give it a full click for constant-on.

Designed with ergonomics in mind, the AXON-SL can also be used as a hand stop and works perfectly mounted to the 12 o'clock rail with the "thumb over bore" or "C-clamp" grip. Whether you want to give your primary the elite touch with a high-end, licensed pressure switch or you're fed up with standard switches dangling, getting snagged and failing when you need them, the PTS Syndicate Unity Tactical AXON-SL Pressure Switch; 2.5mm Plug will serve you well!

If you're running a laser or flashlight with a 2.5mm jack, the PTS Syndicate Unity Tactical AXON-SL Pressure Switch; 2.5mm Plug will make your setup that bit slicker! Designed to mount to 20mm Picatinny rails and take up as little space as possible, the AXON-SL is perfect for compact platforms with little rail space to spare, measuring a mere 4cm end to end.

The set includes a silver 2.5mm plug and a gold 2.5mm plug, both of which are compatible with other plugs in the PTS Unity ecosystem. The switch itself is a single-button switch but can be operated in both momentary-on and constant-on modes. Simply half-press the switch for momentary-on and give it a full click for constant-on.

Designed with ergonomics in mind, the AXON-SL can also be used as a hand stop and works perfectly mounted to the 12 o'clock rail with the "thumb over bore" or "C-clamp" grip. Whether you want to give your primary the elite touch with a high-end, licensed pressure switch or you're fed up with standard switches dangling, getting snagged and failing when you need them, the PTS Syndicate Unity Tactical AXON-SL Pressure Switch; 2.5mm Plug will serve you well!

A Pistol Grip designed by PTS Syndicate for Airsoft M4/15/16 Replicas which follows the same design traits as Magpul Real Steel Accessories and attachments: Ergonomic, Lightweight, Durable and absolutely always tactical.

If you're a fan of modern shooting techniques and rock around with an M4, AR-15 or SCAR-L, this magazine is just for you! The PTS Syndicate EPM 150rnd Mid-Cap Magazine w/ MultiTasker® Mag Pod Base Plate is perfect for realism seekers as the base plate included is designed for real steel magazines but they are also compatible with Airsoft magazines.

The BB guide of the magazine is coloured bright orange, allowing you to see the number of BBs remaining, from the top, side and lower part of the magazine. You can pick up the mag and know exactly how many BBs are remaining. It is constructed from tough DuPont Zytel Polymer, making it extremely durable and robust with a great finish.

The advantage of the MultiTasker® Mag Pod Base Plate is the ability to use your magazine as a makeshift bipod, providing improved stability so you can nail those long-range shots. Adding a bipod adds a lot of weight to the front end but the Mag Pod Base Plate should give you some of the functionality but none of the weight. If you're running a light and handy assault rifle seeking more stability without extra weight.

If you're running a red dot with magnifier setup and want a more comfortable neck position, the PTS Syndicate Unity Tactical FAST™ FTC Aimpoint Magnifier Mount will sort that out! This mount is designed for old-school magnifiers which use a ring-style mount, offering compatibility with most 30mm tube magnifiers including the Vector Optics Flip To Side Magnifier.

Constructed from flawlessly machined CNC aluminium with a steel mounting bolt, this mount is unique in its FTC (Flip to Centre) configuration. This means when stowed, your magnifier won't hang off the side of your primary; instead, it pushes straight down to stow just below your primary optic, keeping the sides of your primary clean for reduced snag potential.

The Unity Tactical FAST™ FTC OMNI Magnifier Mount is set to position your magnifier at 2.26" from the rail to the centre of the optic (aka optical centreline), meaning you will in most cases require an equivalent height riser to align your red dot with your magnifier. Thankfully, PTS offers theFAST Riser,FAST MRO Mount andFAST Micro Mount to facilitate this.

Being higher over the rail than standard magnifier mounts makes this setup ideal for full-face mask users or those who run active hearing protection, avoiding the need for straining your neck to see down your sighting system. If you're running face protection and don't want to ditch your magnifier, the PTS Syndicate Unity Tactical FAST™ FTC Aimpoint Magnifier Mount is what you need!

If you're running a red dot with magnifier setup and want a more comfortable neck position, the PTS Syndicate Unity Tactical FAST™ FTC Aimpoint Magnifier Mount will sort that out! This mount is designed for old-school magnifiers which use a ring-style mount, offering compatibility with most 30mm tube magnifiers including the Vector Optics Flip To Side Magnifier.

Constructed from flawlessly machined CNC aluminium with a steel mounting bolt, this mount is unique in its FTC (Flip to Centre) configuration. This means when stowed, your magnifier won't hang off the side of your primary; instead, it pushes straight down to stow just below your primary optic, keeping the sides of your primary clean for reduced snag potential.

The Unity Tactical FAST™ FTC OMNI Magnifier Mount is set to position your magnifier at 2.26" from the rail to the centre of the optic (aka optical centreline), meaning you will in most cases require an equivalent height riser to align your red dot with your magnifier. Thankfully, PTS offers theFAST Riser,FAST MRO Mount andFAST Micro Mount to facilitate this.

Being higher over the rail than standard magnifier mounts makes this setup ideal for full-face mask users or those who run active hearing protection, avoiding the need for straining your neck to see down your sighting system. If you're running face protection and don't want to ditch your magnifier, the PTS Syndicate Unity Tactical FAST™ FTC Aimpoint Magnifier Mount is what you need!

If you're into modern shooting techniques and running PTS EPM Gen.2 mid-caps, these should interest you! The PTS Syndicate MultiTasker® Mag Pod Base Plate for EPM Gen.2; 3 Pack are genuine real steel magazine enhancements designed for real P-Mag Gen.2 AR-15 magazines but also compatible with PTS EPM Gen.2 mid-cap magazines. 

The advantage of the MultiTasker® Mag Pod Base Plate is the ability to use your magazine as a makeshift bipod, providing improved stability so you can nail those long-range shots. Adding a bipod adds a lot of weight to the front end but the Mag Pod Base Plate should give you some of the functionality but none of the weight. If you're running a light and handy assault rifle seeking more stability without extra weight, the PTS Syndicate MultiTasker® Mag Pod Base Plate for EPM Gen.2; 3 Pack is what you need!

A replacement for your Airsoft gun's standard flash hider, this compact 14mm CW threaded compensator is a small way to dramatically alter the appearance of your Airsoft gun. 

If your helmet is a bit battered, no need to get a new one! The PTS Syndicate Impact Liner for PTS MTEK FLUX Helmet is a complete set of internal padding, the same type used in the PTS MTEK Flux Helmet. The foam padding is very comfortable, a considerable step up from the padding found in most clone helmets and thankfully, this padding should fit other helmets provided they have removable pads and internal velcro.

Whether you're seeking replacement padding for hygiene reasons or you want a comfort improvement, the PTS Syndicate Impact Liner for PTS MTEK FLUX Helmet will do the trick!

A set of improved G-Series pistol magazine base plates designed to fit Tokyo Marui Magazines, made from TPU rubber to absorb impacts!

If you're looking for an interesting flash hider to top off your build, the PTS BattleComp 2.0 Flash Hider is the stylish touch your primary needs! A detailed, licensed replica of the real steel BattleComp 2.0, this flash hider is made from steel and ready to mount on any 14mm Clockwise (CW) male threaded outer barrel.

The real steel BattleComp 2.0 came about following the success of earlier BattleComp muzzle brakes, designed for military applications which require compatibility with QD suppressors. Like the real thing, the PTS BattleComp 2.0 is compatible with "A2 Birdcage" compatible suppressors, including KAC QD style suppressors and the B&T Rotex QD suppressor. If your primary has a 14mm clockwise threaded barrel and it needs a top notch muzzle device, the PTS BattleComp 2.0 Flash Hider is ideal!

If you're seeking replacement accessory rails for your PTS MTEK Flux helmet, you've found what you need! The PTS Syndicate M-LOK Accessory Rails for MTEK FLUX Helmet are made from Dupont Zytel Polymer and designed specifically for the PTS MTEK Flux. These rails provide M-LOK slots positioned horizontally and vertically, allowing a plethora of accessories to be mounted including headset arms and navigation lights.

These accessory rails are only for the Flux and are unlikely to fit other brands without modification. Whether you're refurbishing an old helmet or adding some unique contrast to make your lid stand out, the PTS Syndicate M-LOK Accessory Rails for MTEK FLUX Helmet are a fine choice!

If you're seeking replacement accessory rails for your PTS MTEK Flux helmet, you've found what you need! The PTS Syndicate M-LOK Accessory Rails for MTEK FLUX Helmet are made from Dupont Zytel Polymer and designed specifically for the PTS MTEK Flux. These rails provide M-LOK slots positioned horizontally and vertically, allowing a plethora of accessories to be mounted including headset arms and navigation lights.

These accessory rails are only for the Flux and are unlikely to fit other brands without modification. Whether you're refurbishing an old helmet or adding some unique contrast to make your lid stand out, the PTS Syndicate M-LOK Accessory Rails for MTEK FLUX Helmet are a fine choice!

If you're running the PTS FAST LPVO mount and want a quick way to engage close-range threats, the PTS Syndicate Unity Tactical Top Ring for FAST LPVO Mount w/MRDS Adjustable Plate lets you do just that. This set includes an upper scope ring for the PTS FAST LPVO mount, a screw set and the PTS MRDS modular mount plate.

Designed to fit practically any common MRDS footprint, the PTS Modular MRDS plate mounts to the top of the included ring, which itself can be used to replace either the front or rear ring on your PTS FAST LPVO mount. The MRDS mount is confirmed to fit Docter, RMR®, Shield RMS/ RMSc, Sig Romeo Pistol Red Dot Sight, C-more, Sightmark M-Spec, Holosun-K and DeltaPoint® Pro footprint red dot sights.

If you've ever missed a kill because you were busy adjusting magnification, the PTS Syndicate Unity Tactical Top Ring for FAST LPVO Mount w/MRDS Adjustable Plate with an MRDS installed will ensure that never happens again!

If you're running the PTS FAST LPVO mount and want a quick way to engage close-range threats, the PTS Syndicate Unity Tactical Top Ring for FAST LPVO Mount w/MRDS Adjustable Plate lets you do just that. This set includes an upper scope ring for the PTS FAST LPVO mount, a screw set and the PTS MRDS modular mount plate.

Designed to fit practically any common MRDS footprint, the PTS Modular MRDS plate mounts to the top of the included ring, which itself can be used to replace either the front or rear ring on your PTS FAST LPVO mount. The MRDS mount is confirmed to fit Docter, RMR®, Shield RMS/ RMSc, Sig Romeo Pistol Red Dot Sight, C-more, Sightmark M-Spec, Holosun-K and DeltaPoint® Pro footprint red dot sights.

If you've ever missed a kill because you were busy adjusting magnification, the PTS Syndicate Unity Tactical Top Ring for FAST LPVO Mount w/MRDS Adjustable Plate with an MRDS installed will ensure that never happens again!

The MEC M-Valve from PTS is designed to improve gas efficiency and speed up the cyclic rate of your KWA/KSC GBB pistol or SMG. The valve is constructed from high strength brass with rubber O-rings and should help improve the performance of your pistol in cold weather, and speed up the cyclic rate if you have installed a heavy steel slide or bolt.

A replacement ergonomic grip for AK Platform Series AEGs, giving you a comfortable and larger surface area to hold onto, giving you better control over your Airsoft weapons.

If you have dropped a GBB pistol magazine before, you will know the pain of a small but costly mistake ruining your magazine. The Enhanced Pistol Shockplate from PTS Syndicate is designed to prevent this; with a combination of high-density polymer and impact-resistant hard rubber in its construction your magazine has never stood a better chance of surviving a drop than it will with one of these installed!

If you're seeking a way to style up your PTS EPM-AR9 magazines, these will do the trick! The PTS Syndicate EPM-AR9 Magazine Baseplate; 3 Pack are constructed from the same rock-solid Dupont Zytel Polymer as the originals but finished in red, adding a touch of contrast to your setup to make it really pop.

Like the original black baseplates, the red versions have a dot matrix on each, ideally suited to marking your magazines, either numerically or to identify which mag is yours. The set also includes 3 mounting screws which is great news for those who've lost one. If you're an aggressive skirmisher who values style over concealment, the PTS Syndicate EPM-AR9 Magazine Baseplate; 3 Pack in spicy red will suit your needs perfectly!

A replacement grip for AK platform series GBB rifles, giving you a larger surface area to hold onto and better weapons handling.

If you like the style of micro red dots and want to mount one on your rifle at a comfortable height, then you need this! The PTS Syndicate Unity Tactical Fast™ MRDS mounts on 20mm Picatinny rails and includes an MRDS Adjustable Plate that fits most micro red dot footprints. These footprints include Docter, RMR®, Shield RMS/ RMSc, Sig Romeo Pistol Red Dot Sight, C-more, Sightmark M-Spec, Holosun-K and DeltaPoint® Pro footprint red dot sights.

It is constructed from CNC 6000 aluminium, making it durable and lightweight, perfect for agile skirmishers who like to keep a low profile on the battlefield. If you aim best with a micro red dot and want to comfortably mount one on something other than your pistol, you need the PTS Syndicate Unity Tactical Fast™ MRDS Mount w/MRDS Adjustable Plate!

If you are the type of player who uses a full loadout of midcaps, and you want to reload and get ready for the next game in just a few seconds, we have a treat for you! Introducing the M12 Sidewinder Speed Loader from PTS Syndicate, an ultra quick crank wound speed loader which can load a midcap in an astonishing 4 seconds of winding! This speed loader has a whopping 1600 round capacity, and is widely known for its reliability.

If you are the type of player who uses a full loadout of midcaps, and you want to reload and get ready for the next game in just a few seconds, we have a treat for you! Introducing the M12 Sidewinder Speed Loader from PTS Syndicate, an ultra quick crank wound speed loader which can load a midcap in an astonishing 4 seconds of winding! This speed loader has a whopping 1600 round capacity, and is widely known for its reliability.

Another excellent quality product from PTS, a 170rd Mid Cap magazine for those of you looking for a more low profile but reliable magazine option.