All Airsoft Batteries

A high quality and compact PEQ box sized 11.1v Lithium Polymer Battery with 1300mAh of capacity, and a 20C discharge rating

A LiPo saddle battery designed to fit in handguards in replacement of the traditional 1600mAh NiMH blocks/saddles (G36 handguards etc).

An absolutely massive 11.1v 2000mAh Li-Ion battery in a stick configuration, which allows you to squeeze as much lifespan out of your Airsoft Electric Gun as possible, by offering a lower cost and higher power density vs. LiPo batteries.

An absolutely massive 11.1v 2000mAh Li-Ion battery in a stick configuration, which allows you to squeeze as much lifespan out of your Airsoft Electric Gun as possible, by offering a lower cost and higher power density vs. LiPo batteries.

An 11.1v 2000mAh Li-Ion battery for Airsoft Electric Guns, which comes supplied in a Crane/Butterfly/Saddle configuration, meaning two rows of cells. This makes them very easy to place in awkard-to-fit spots such as Handguards and Crane Stocks, and will provide better Power Density that traditional LiPo batteries.

An 11.1v 1200mAh 20c LiPo Battery with a Deans Connector in a Stick configuration, making it ideal for Solid Stocks and some rear wired Buffer Tubes. It has the following dimensions with a 9cm cable: 2cm x 1.63cm x 13cm.

An ultra-thin and lightweight battery, perfect for squeezing into even the tightest spots. This battery provides 1200mAh of power with a discharge rate of 30c. Being short and wide, this battery is perfect for PEQ boxes and solid stocks.

An absolutely massive 11.1v 2000mAh Li-Ion battery in a stick configuration, which allows you to squeeze as much lifespan out of your Airsoft Electric Gun as possible, by offering a lower cost and higher power density vs. LiPo batteries.

An absolutely massive 11.1v 2000mAh Li-Ion battery in a stick configuration, which allows you to squeeze as much lifespan out of your Airsoft Electric Gun as possible, by offering a lower cost and higher power density vs. LiPo batteries.

Suitable not only for Airsoft but for RC vehicles and toys too, this  7.4v 2200mAh LiPo Stick Battery will fit in tight areas like stock tubes and handguards where other batteries would normally not.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

If you need a battery for your M4/AR-15 AEG Crane stock and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configuration with a Deans connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2 cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery with a Mini-Tamiya connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a buffer tube battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 1.3cm x 1.5cm with approximately 9cm of wiring between the battery and connector