FPS Softair

Upgrade your AEG with a replacement shim set for increased gear stability, precise adjustment and gearbox longevity. Featuring steel ST 2 K60 construction, available in a variety of thicknesses.

Specifications:

• 20 pcs
• 0.1/0.2/0.3/0.5 mm thickness
• 3 mm internal hole
• 6 mm diameter

Upgrade your stock AEG spring with a Softair's range of high-quality carbon steel springs for superior performance that may give you an edge in gameplay and improve your replica's reliability.

Constructed from burnished and pre-hardened carbon steel wire, the spring also has the addition of silicon and chromium for improved tensile strength and to reduce friction to reduce energy loss. It is recommended to use the spring in association with spring guides and bearing piston heads to ensure maximum performance and durability. The spring also features closed and flattened top and bottom ends to improve stability, with the spring also reducing stress on your replicas pistons due to the non-linear design.

Available in various strengths providing roughly 300, 345, 360 and 395 FPS respectively.

If you have a sniper rifle project on the go and your base gun is a TM VSR-10 or clone, an FPS Softair Upgrade Spring will be very useful! These springs are designed for the Tokyo Marui VSR-10 platform and should fit the various clone VSR-10 sniper rifles on the market, including the Well MB02, MB03, MB07 and MB10, the JG BAR-10, CYMA CM.701 and HFC USR-11.

FPS Softair offers a wide range of springs, so no matter what power level you are seeking, they have you covered! Options include M90 and M100 for low-velocity setups focussed on easy cocking, low wear and quiet muzzle report and M120 or M140 options for those who want to push their power level up for better range.

FPS Softair brings us a Carbon Fibre Reinforced AEG Tappet Plate for use with version 2 gearboxes. It is specially formulated to be strong yet flexible enough to bend slightly.

The plate is constructed from extremely lightweight polycarbon and is designed to be attached to the air nozzle and sector gear. This process controls the feeding of BBs from the magazine into the hop up chamber.

If you're tuning up your TM NGRS, the FPS Softair Upgrade Spring for Tokyo Marui NGRS will be useful! Available in M95, M100 or M105 strengths, this spring will work in any Tokyo Marui NGRS gearbox, including M4 variants, the 416, SCAR-L and H.

The FPS Softair Upgrade Spring is made from carbon steel wire (EN10270 / 2) with silicone and chrome additives and is heat-treated to extend its lifespan. We recommend pairing this upgrade spring with upgraded bushings, an upgraded spring guide and a ball bearing piston head to maximise reliability. If you're going for higher FPS in your NGRS build, the FPS Softair Upgrade Spring for Tokyo Marui NGRS is what you need!

If you have a sniper rifle project on the go and your base gun is a Maruzen APS2 Type 96 clone, an FPS Softair Upgrade Spring will be very useful! These springs are designed for the Maruzen APS2 Type 96 pattern of L96 Airsoft sniper rifle (Well MB01, Well MB08 etc) but won't fit the more recently designed Tokyo Marui L96 pattern or the AGM 002 L96.

FPS Softair offers a wide range of springs, so no matter what power level you are seeking, they have you covered! Options include M90 and M100 for low-velocity setups focussed on easy cocking, low wear and quiet muzzle report and M120 or M140 options for those who want to push their power level up for better range.

Standard guides do not feature ball bearings, and these are included in this product because they reduce stress on the spring by letting it rotate freely. When upgrading your gearbox bearing spring guides should always be considered because they will improve the life-span of a spring by reducing sideways stresses.

The spring bearing is construction from tough but lightweight aluminium Ergal with a smooth anodised finish. Fits version 2 gearboxes in replicas models such as M4, M16, SR16, SMG-3, MC51, G3, MINIMI, LR300.

If you're working on a gearbox build, FPS Softair 8mm Self Lubricating CNC Steel Bushings will give your build a long life of friction-free performance! Constructed from CNC machined steel, these 8mm solid bushings are compatible with any AEG gearbox which uses 8mm bushing/bearing holes. 

The advantage of solid bushings over ball-bearing bushings is their incredible strength, ideal for high-performance builds whether it's a DMR or DSG. If you're pushing the limits of Airsoft performance, FPS Softair 8mm Self Lubricating CNC Steel Bushings belong in your build!

Upgrade your AEGs piston head to improve air seal and increase the efficiency of airflow through the cylinder. This piston from FPS Softair has ports on the front to push out the O-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

Constructed from CNC aluminium Ergal, which has been anodised, the piston head features a smooth precise surface. The piston head has ports on the front to push out the O-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape.

This is the most advanced version with 8 ventilation holes for higher speed and rate of fire, double O-ring and ball-bearing. This head is designed for version 2 and 3 gearboxes but may fit other types.

Increase your electric M4/M16s power and air efficiency with an upgraded nozzle and O-ring. With its robust CNC Delrin construction, this will make a great enhancement over your stock nozzle and is to be used with version 2 gearboxes.

Make sure to use pure silicone oil to lubricate your cylinder head's nozzle stem before installing this nozzle.

Increasing the rate of fire on your airsoft rifle sometimes causes it to misfeed, resulting in dry firing. A sector gear delay will solve your feeding problems 99.9% of the time with a simple add-on.

This sector gear clip increases the time it takes for the air nozzle to cycle. Delaying the cycle improves BB feeding by allowing the air nozzle to be retracted from the hop-feed for a longer duration.

This tiny add-on could instantly transform your AEG if it has been suffering from firing issues.

Although this is designed to be a perfect fit, it is recommended that this be permanently fixed in place using superglue, after testing to prevent it from potentially loosening over time.

If you're upgrading your AK-47/74 AEG, the FPS Softair ERGAL Air Nozzle with Inner O-Ring for AK-47/74 AEG is an essential part! Made from super-strong CNC-machined ERGAL, this nozzle is about as strong as AEG nozzles get, ideal for high-performance builds intended to last.

ERGAL is the trade name for 7075 aluminium alloy, known for its exceptional strength and low weight, rivalling some steels in strength while staying light as a feather by comparison. This nozzle also features an internal O-ring designed to minimise air leaks for maximum consistency and ensure the nozzle stays perfectly aligned for reliable feeding with every shot. If you need a super strong nozzle for a high-performance AK AEG build, you won't find any better than the FPS Softair ERGAL Air Nozzle with Inner O-Ring!

If you love working on gearboxes or have a version 3 custom build on the cards, the FPS Softair Complete Gearbox Spring Set for V3 Gearbox belongs in your toolbox. This set includes all of the springs needed for a version 3 gearbox build, including the tappet plate spring, ARL spring, motor height spring, cut-off lever spring, trigger return spring and switch return spring.

All of the springs in this set have been manufactured by FPS Softair to be more durable than the original springs and with more precisely calculated tension for maximum efficiency. Whether you've lost a spring, are working on a version 3 gearbox build or need spares for your technical projects, the FPS Softair Complete Gearbox Spring Set for V3 Gearbox will be useful addition to your parts bin!

If you're working on a high-speed or high FPS gearbox, the FPS Softair Carbon Fibre Reinforced Tappet Plate for V3 Gearbox is essential. This hard-wearing tappet plate is constructed from carbon fibre-reinforced polymer, making it strong and flexible in equal measure. We've had superb results installing the Version 2 equivalent of this tappet plate in Bolster Armouries builds and if you seek similar performance we would wholeheartedly recommend this plate over others.

This Carbon Fibre Tappet Plate is compatible with any version 3 Airsoft gearbox, including those found in AUG, AR36, AK & S55x AEGs. Whether you're building a DMR or a beast of a high-speed setup, the FPS Softair Carbon Fibre Reinforced Tappet Plate for V3 Gearbox is the ideal upgrade to keep it feeding!

Take your sniper to the next level and reduce those all-important decibels with a silencer adaptor. This aluminium constructed thread adaptor allows you install muzzle devices such as suppressors and tracer units. Simply remove the barrel cap and replace it with this adaptor for a seamless transition to the muzzle device of your choice.

The adaptor provides a 14mm CCW thread to customise your replica, and is compatible with the MB01, MB04 and MB05 spring-powered Airsoft sniper rifles

Take your sniper to the next level and reduce those all-important decibels with a silencer adaptor. This aluminium constructed thread adaptor allows you to install muzzle devices such as suppressors and tracer units. Simply remove the barrel cap and replace it with this adaptor for a seamless transition to the muzzle device of your choice.

The adaptor provides a 14mm CCW thread to customise your replica, and is compatible with the MB-02 spring-powered Airsoft sniper rifles

Upgrade your AEG with an FPS Softair Stainless Steel Cylinder and increase its reliability and performance. The cylinder is constructed from high-strength steel and is resistant to fatigue with increased durability. The cylinder is made for use with version 2 or 3 gearboxes, compatible with Tokyo Marui derived designs, with barrel lengths of 251 to 330mm.

Increasing the rate of fire on your airsoft rifle sometimes causes it to misfeed, resulting in dry firing in builds with a very high rate of fire. A sector gear delay will solve your feeding problems 99.9% of the time with a simple add-on.

This sector gear clip increases the time it takes for the air nozzle to cycle. Delaying the cycle improves BB feeding by allowing the air nozzle to be retracted from the hop-feed for a longer duration.

This tiny add-on could instantly transform your AEG if it has been suffering from high rate of fire issues.

Although this is designed to be a perfect fit, it is recommended that this be permanently fixed in place using superglue, after testing to prevent it from potentially loosening over time.

Increase the power and air efficiency of your A&K M249 Series AEG with an upgraded nozzle and O-ring. With its CNC Aluminium Ergal construction and smooth anodized finish, this will drastically improve your AEG's performance compared to the standard polymer nozzle included with the A&K M249 AEG.

The included O-rings provide a far superior air seal. For the best results, make sure to use pure silicone oil to lubricate your cylinder head's nozzle stem before installing this nozzle.

If you're building out your MP5/SMG-5 AEG for high performance, the FPS Softair ERGAL Air Nozzle with Inner O-Ring for MP5/SMG-5 AEG will ensure it's reliable and accurate! Made from super-strong CNC-machined ERGAL, this nozzle is about as strong as AEG nozzles get, ideal for high-performance builds intended to last.

ERGAL is the trade name for 7075 aluminium alloy, known for its exceptional strength and low weight, rivalling some steels in strength while staying light as a feather by comparison. This nozzle also features an internal O-ring designed to minimise air leaks for maximum consistency and ensure the nozzle stays perfectly aligned for reliable feeding with every shot. If you need a super strong nozzle for a beastly MP5/SMG-5 AEG build, the FPS Softair ERGAL Air Nozzle with Inner O-Ring is the way to go!

Upgrade your AEG with some advanced Open Steel Bearing Bushings from FPS Softair. Upgrading your bushings will decrease the friction caused by gear rotation, resulting in a higher burst speed and better energy efficiency. The open bearing ensures higher strength compared to closed because the ball bearings are larger.

Dimensions:

• Outer diameter: 8 mm
• Inner hole: 3 mm
• Thickness: 2.5 mm

FPS Softair brings us a Carbon Fibre Reinforced AEG Tappet Plate for use with version 2 gearboxes. It is specially formulated to be strong yet flexible enough to bend slightly.

The plate is constructed from extremely lightweight polycarbon and is designed to be attached to the air nozzle and sector gear. This process controls the feeding of BBs from the magazine into the hop up chamber.

Upgrade your M4/M16 AEG with an FPS Softair Stainless Steel Cylinder and increase its reliability and performance. The cylinder is extremely durable and is more resistant to the constant friction caused by the piston head. The cylinder is made for use with version 2 or 3 gearboxes, compatible with Tokyo Marui derived designs and clones, with barrel lengths of 401mm to 450mm.

If you're working on a long-barreled AR36 AEG build, whether it's a DMR or an MG36 LMG, the FPS Softair Full Tune Up Kit for AR36 AEGs is the ideal addition to your build. This kit includes replacements for the full cylinder group, enhancing air seal, and improving longevity and overall efficiency.

The kit is optimised for inner barrels of 451-550mm in length and includes a Type F CNC Steel Cylinder, ERGAL Nozzle with O-ring, CNC Aluminium cylinder head and a CNC ERGAL Double O-ring ball-bearing advanced piston head. If you're looking for maximum efficiency and strength from your long-barreled AR36 build, you need this kit!

If you're looking for a sturdy upgrade to your AEG, the FPS Softair Piston Head O-Ring Seal is a worthy contender. Constructed from high-density rubber for a superior seal to increase the reliable and lifespan of your rifle. This O-ring is likely to improve your air consistency, which may result in increased accuracy and is compatible with most piston heads.

If you're working on a high-performance build with 8mm bushing ports, the FPS Softair Low-Profile 8mm Self-Lubricating CNC Steel Bushings for AEG are what you need. CNC-machined from steel with a low-friction coating, these bushings will work with any standard AEG gearbox with 8mm bushing ports.

When compared to standard bushings, the FPS Sofair equivalent is far stronger and has a self-lubricating coating, which considerably reduces friction and prevents wear on the gearbox shell and gear axles. If you're planning a high-performance build which needs to last a lifetime, FPS Softair Low-Profile 8mm Self-Lubricating CNC Steel Bushings for AEG are essential!

If you're upgrading your Cybergun/VFC SCAR-H, the ERGAL Air Nozzle with Inner O-Ring for VFC SCAR-H AEG from FPS Softair is essential for reliability and accuracy! Made from super-strong CNC-machined ERGAL, this nozzle is about as strong as AEG nozzles get, ideal for high-performance builds intended to last. Compatibility-wise, this nozzle is designed specifically for the VFC-manufactured SCAR-H (sometimes branded Cybergun) and may also fit D-Boys SCAR-H AEGs, but won't work with other SCAR-H replicas.

ERGAL is the trade name for 7075 aluminium alloy, known for its exceptional strength and low weight, rivalling some steels in strength while staying light as a feather by comparison. This nozzle also features an internal O-ring designed to minimise air leaks for maximum consistency and ensure the nozzle stays perfectly aligned for reliable feeding with every shot. If you need a top-of-the-range nozzle for your VFC SCAR-H custom build, the FPS Softair ERGAL Air Nozzle with Inner O-Ring for VFC SCAR-H AEG is ideal!

If you're working on a gearbox build with 7mm bushing ports, the FPS Softair 7mm Steel Self-lubricating Bushings for AEG are a robust, smooth-running solution! Made from steel with a low-friction coating, these bushings will work with any standard AEG gearbox with 7mm bushing ports. 

When compared to standard bushings, the FPS Sofair equivalent is far stronger and has a self-lubricating coating, which considerably reduces friction and prevents wear on the gearbox shell and gear axles. If you're planning a high-performance build which needs to last a lifetime, FPS Softair 7mm Steel Self-lubricating Bushings for AEG are an integral part!

Keep your TM NGRS build reliable with the FPS Softair Carbon Fibre Piston with Full Metal Rack; TM M4 NGRS! A super-strong piston made from carbon fibre-infused technopolymer with a full tooth rack made from SAE 4650 alloy, this is about the best M4 NGRS piston on the market, made in Italy by Airsoft upgrade Gods, FPS Softair.

The rack is made from copper-beryllium alloy using the MIM (metal injection moulding) process, ensuring tolerances are tight, surface finish is precise, and strength is at a peak, rivalling and exceeding many Airsoft pistons with mild steel racks. If you're upgrading anything else on your TM M4 NGRS, the FPS Softair Carbon Fibre Piston with Full Metal Rack; TM M4 NGRS is essential!

If you're the techy type seeking high-quality MOSFET wiring, FPS Softair has your back with the High Conductivity MOSFET Signal Cable! Made with 19 pure copper capillaries coated in chrome to enhance conductivity, this signal wire is specifically designed to provide maximum efficiency while avoiding being too thick and impinging on gearbox internals. We all know the pain of discovering your pinion gear has shredded your wiring. Thankfully, this FPS Signal Wire sidesteps this issue entirely!

The capillaries are protected with an FEP (Fluorinated Ethylene Propylene) coating, keeping the wire flexible to be routed through tight spaces, ideal for whatever custom setup you have in mind. If you're an ambitious tech with some wild custom build plans, FPS Softair High Conductivity MOSFET Signal Cable will definitely come in handy!