VORSK Airsoft

A Performance enhancing Green Gas designed for use in Alloy / Metal slide Gas Blowback Pistols & Rifles. The VORSK V6 Green Gas provides you with a highly consistent composition of Gas to Silicone lubricant ratio, thus keeping your magazines and seals healthy while providing you with a super strong recoil and great shot-to-shot consistency! VORSK V6 Is the perfect Fuel for your Pistol!  

Looking for spare magazines for the VORSK VMP-1 or VMP-2? You have found them! The VORSK 45rnd Magazine for VMP GBB Series is constructed from alloy with a steel feed spring and brass valves, holding 45 BBs which can be loaded either by hand through the feed lips at the top or using a speed loader. The fill valve is on the baseplate and as with all GBB mags, you'll need to invert the mag to fill it with gas.

Please note, these magazines do not include the polymer magazine sleeve, but you can grab them here: Sleeve for VMP-1 | Sleeve for VMP-2

Ideal for VMP-1 or VMP-2 users who need maximum capacity, this magazine is also compatible with ASG MP9 and KWA TP9 replicas. If you're gearing up to run the VMP-1 or any VMP-2 variant, these magazines are essential!

VORSK V8! A Performance enhancing Green Gas designed for use in Alloy / Metal slide Gas Blowback Pistols & Rifles. The VORSK V8 Green Gas provides you with a highly consistent composition of Gas to Silicone lubricant ratio, thus keeping your magazines and seals healthy while providing you with a super strong recoil and great shot-to-shot consistency! VORSK V8 Is the perfect Fuel for those of you looking for a little more kick! 

Want to make your VMP-2 magazines look great and far easier to handle? The Magazine Sleeves for VMP-2 GBB Magazines; 2 Pack is just the thing! The magazine cover sleeves are supplied in a pack of 2 covers and are designed to slip over the lower section of the VMP GBB magazine and make them easier to handle in wet and cold weather and fit perfectly with the VMP-2. 

Installation is as simple as slipping the cover over the bottom of the magazine with the baseplate removed, and then reinstalling the baseplate to secure it in place. Please note, with these sleeves on your magazines you will no longer be able to insert them into a VMP-1. 

Want to make your VMP-2 magazines look great and far easier to handle? The Magazine Sleeves for VMP-2 GBB Magazines; 2 Pack is just the thing! The magazine cover sleeves are supplied in a pack of 2 covers and are designed to slip over the lower section of the VMP GBB magazine and make them easier to handle in wet and cold weather and fit perfectly with the VMP-2. 

Installation is as simple as slipping the cover over the bottom of the magazine with the baseplate removed, and then reinstalling the baseplate to secure it in place. Please note, with these sleeves on your magazines you will no longer be able to insert them into a VMP-1. 

Want to make your VMP-2 magazines look great and far easier to handle? The Magazine Sleeves for VMP-2 GBB Magazines; 2 Pack is just the thing! The magazine cover sleeves are supplied in a pack of 2 covers and are designed to slip over the lower section of the VMP GBB magazine and make them easier to handle in wet and cold weather and fit perfectly with the VMP-2. 

Installation is as simple as slipping the cover over the bottom of the magazine with the baseplate removed, and then reinstalling the baseplate to secure it in place. Please note, with these sleeves on your magazines you will no longer be able to insert them into a VMP-1. 

Want to make your VMP-2 magazines look great and far easier to handle? The Magazine Sleeves for VMP-2 GBB Magazines; 2 Pack is just the thing! The magazine cover sleeves are supplied in a pack of 2 covers and are designed to slip over the lower section of the VMP GBB magazine and make them easier to handle in wet and cold weather and fit perfectly with the VMP-2. 

Installation is as simple as slipping the cover over the bottom of the magazine with the baseplate removed, and then reinstalling the baseplate to secure it in place. Please note, with these sleeves on your magazines you will no longer be able to insert them into a VMP-1. 

Want to make your VMP-2 magazines look great and far easier to handle? The Magazine Sleeves for VMP-2 GBB Magazines; 2 Pack is just the thing! The magazine cover sleeves are supplied in a pack of 2 covers and are designed to slip over the lower section of the VMP GBB magazine and make them easier to handle in wet and cold weather and fit perfectly with the VMP-2. 

Installation is as simple as slipping the cover over the bottom of the magazine with the baseplate removed, and then reinstalling the baseplate to secure it in place. Please note, with these sleeves on your magazines you will no longer be able to insert them into a VMP-1. 

If you're running your VMP-1 SMG as a backup or cutting about with the beastly VMP-2D or MD, the VORSK 20rnd Short Gas Magazine for VMP GBB Series is the compact magazine you need! This green gas magazine holds 20 BBs and is designed for the VORSK VMP-1 and VMP-2 GBB platforms. The mag is loaded through the feed lips on the top or through the follower channel by pulling the follower on the front down. You can use a speed loader or load by hand, depending on your timescale!

Filling the internal gas reservoir requires that you invert the magazine, indexing your green gas can with the fill valve on the baseplate. VORSK recommends V6 or V8 green gas for this magazine to stay within its performance parameters. The major advantage of this mag is its short overall length, allowing you to get lower in the prone position and take advantage of surrounding cover. If you dream of using your VMP-1 like a giant pistol or need compact mags to suit your VMP-2D or VMP-2MD DMR, these are what you need!

Want to make your VMP-1 SMG magazines look great and far easier to handle? The VMP-1 GBB SMG Magazine cover is just the thing! The magazine cover sleeves are supplied in a pack of 2 covers and is designed to slip over the lower section of the VMP-1 magazine and make them easier to handle in wet and cold weather. Making the magazine look more in keeping with the cutting-edge external design of the VMP-1 itself is just a bonus! Installation is as simple as slipping the cover over the bottom of the magazine with the baseplate removed, and then reinstalling the baseplate to secure it in place.

If you want the stealthy aesthetic for your SMG or rifle, this is how you do it! The VORSK QD Suppressor with 5-Lug Flash Hider; 14mm CCW is compatible with the VORSK VMP series and now any Airsoft replica with a 14mm CCW male threaded barrel thanks to the inclusion of the super aggressive 5-lug flash hider. The suppressor mounts to the 5-lug muzzle device via a QD interface, meaning it can quickly be removed and reinstalled when needed.

Constructed from aluminium with a foam filling, this suppressor should dampen the muzzle report of your SMG or rifle slightly but its main role is to provide slick looks. There also is plenty of space inside to fit a custom foam filling or tracer module if you are happy with a bit of fabrication!

If you're running the VMP-2D or VMP-2MD and want to tune muzzle energy, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2MD and VMP-2D barrel lengths. Muzzle energy will be slightly higher with longer barrel lengths and slightly lower with shorter barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD was made with you in mind!

If you're running the VMP-2D or VMP-2MD and want to tune muzzle energy, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2MD and VMP-2D barrel lengths. Muzzle energy will be slightly higher with longer barrel lengths and slightly lower with shorter barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD was made with you in mind!

If you're running the VMP-2D or VMP-2MD and want to tune muzzle energy, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2MD and VMP-2D barrel lengths. Muzzle energy will be slightly higher with longer barrel lengths and slightly lower with shorter barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD was made with you in mind!

If you're running the VMP-2D or VMP-2MD and want to tune muzzle energy, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2MD and VMP-2D barrel lengths. Muzzle energy will be slightly higher with longer barrel lengths and slightly lower with shorter barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2D & VMP-2MD was made with you in mind!

The VORSK VP Magazine for MWS/VMAR Series GBBRs is a gas blowback rifle magazine designed to support realistic gameplay while keeping ownership practical for regular skirmish use. Compatible with MWS-pattern GBBR platforms, this magazine offers realistic capacity options and efficient gas usage to help players run multiple magazines as part of a proper loadout.

Internally, the magazine uses a simplified architecture designed to improve gas efficiency and reduce unnecessary mechanical complexity. This approach not only supports more consistent cycling but also makes maintenance easier for players who service their own gas magazines. Under typical conditions, the magazine can deliver approximately 65 to 100 shots per gas fill, depending on the variant and firing conditions.

A full steel internal structure provides authentic weight and durability, while the HIPS polymer outer shell balances strength with practical weight. Combined with proven VORSK valve systems, the VMAR series is designed to provide dependable performance for players running MWS gas blowback rifles in both training and skirmish environments.

The VORSK VP Magazine for MWS/VMAR Series GBBRs is a gas blowback rifle magazine designed to support realistic gameplay while keeping ownership practical for regular skirmish use. Compatible with MWS-pattern GBBR platforms, this magazine offers realistic capacity options and efficient gas usage to help players run multiple magazines as part of a proper loadout.

Internally, the magazine uses a simplified architecture designed to improve gas efficiency and reduce unnecessary mechanical complexity. This approach not only supports more consistent cycling but also makes maintenance easier for players who service their own gas magazines. Under typical conditions, the magazine can deliver approximately 65 to 100 shots per gas fill, depending on the variant and firing conditions.

A full steel internal structure provides authentic weight and durability, while the HIPS polymer outer shell balances strength with practical weight. Combined with proven VORSK valve systems, the VMAR series is designed to provide dependable performance for players running MWS gas blowback rifles in both training and skirmish environments.

A Super Performance enhancing Green Gas designed for use in Gas Blowback Rifles. The VORSK V12 Green Gas provides you with a highly consistent composition of Gas to Silicone lubricant ratio, thus keeping your magazines and seals healthy while providing you with an ULTRA STRONG recoil and great shot-to-shot consistency! VORSK V12 Is the perfect Fuel for your GBBR. 

If you're running the VMP-2M and want to tune it to DMR power levels, the VORSK Replacement Nozzle for VMP-2M is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2M barrel length. Muzzle energy will be slightly higher with longer barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2M was made with you in mind!

If you're running the VMP-2M and want to tune it to DMR power levels, the VORSK Replacement Nozzle for VMP-2M is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2M barrel length. Muzzle energy will be slightly higher with longer barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2M was made with you in mind!

If you're running the VMP-2M and want to tune it to DMR power levels, the VORSK Replacement Nozzle for VMP-2M is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2M barrel length. Muzzle energy will be slightly higher with longer barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2M was made with you in mind!

If you're running the VMP-2M and want to tune it to DMR power levels, the VORSK Replacement Nozzle for VMP-2M is what you need! Available in a range of power levels, including 300 FPS, 330 FPS, 430 FPS and 450 FPS, these nozzles are colour coded so you can tune to perfection without the confusion.

While these nozzles are compatible with all VMP-2 variants, the stated power level only applies to the VMP-2M barrel length. Muzzle energy will be slightly higher with longer barrel lengths, so please keep this in mind. The nozzle spring is also pre-installed in each nozzle to make installation that bit easier. If you're the type to take full advantage of your VMP-2's modularity, the VORSK Replacement Nozzle for VMP-2M was made with you in mind!

If you've been keeping up with anything Airsoft, you must be excited about this one! The Vorsk VMP-2D is here and this gas blowback DMR rifle is a game changer. Out of Vorsk's new line, this variant is the big boy, the full-fat DMR version. Equipped with a longer M-LOK handguard, extended outer barrel, and marksman stock with an adjustable cheek riser, this is the VMP-2 for long-range specialists. With a locked semi-auto function, this rifle delivers precise shots at up to 450 FPS with 0.2g BBs, making it a powerful choice for any marksman.

The VMP-2 is compatible with standard VMP-1/MP9 magazines and makes use of a unique chassis system with QD sling sockets on each side. It is compatible with M4/AR-15 GBBR pistol grips and features mounts for the prolific M4/AR-15 buffer tube at the rear. The D variant features a fixed marksman-style stock with an adjustable cheek riser which is exactly what you need to get a good view of your target down a rifle scope!

The HOP-up unit has a unique design with an external TDC adjuster, perfect for convenient mid-game setting changes to keep up with the versatile conditions, not to mention being an inherently accurate and precise design. The HOP-up bucking and inner barrel are also VSR-10 spec, giving you almost unlimited options for tuning performance to meet your needs.

In case you haven’t heard, the VMP-2 is VORSKs second long-gun platform designed as a multi-role carbine available in 3 unique variants. This, the VMP-2MD is the “recce rifle” variant, locked to semi-automatic only and tuned to DMR FPS levels. The MD is rocking the same handguard and sliding adjustable stock as the M version with a cheek riser added along with an extended barrel, making it ideal for mobile marksmen playstyles and long-range outdoor warfare!

The VMP-2 is compatible with standard VMP-1/MP9 magazines and makes use of a unique chassis system with QD sling sockets on each side, compatibility with M4/AR-15 GBBR pistol grips and the prolific M4/AR-15 buffer tube at the rear, offering full compatibility with aftermarket AR-15 stocks.

The HOP-up unit is a unique design with an external TDC adjuster, ideal for convenient mid-game setting changes to make the most of changing conditions, not to mention being an inherently accurate design. The HOP-up bucking and inner barrel are also VSR-10 spec, giving you almost unlimited options when it comes to tuning performance to meet your needs.

Our VMP-2 batch has now landed and is ready for immediate dispatch! Those who’ve already made their mind up, get your order in now to make sure you get one of the first VMP-2 platforms available worldwide!