All Spring Internals

If you have a sniper rifle project on the go and your base gun is a TM VSR-10 or clone, an FPS Softair Upgrade Spring will be very useful! These springs are designed for the Tokyo Marui VSR-10 platform and should fit the various clone VSR-10 sniper rifles on the market, including the Well MB02, MB03, MB07 and MB10, the JG BAR-10, CYMA CM.701 and HFC USR-11.

FPS Softair offers a wide range of springs, so no matter what power level you are seeking, they have you covered! Options include M90 and M100 for low-velocity setups focussed on easy cocking, low wear and quiet muzzle report and M120 or M140 options for those who want to push their power level up for better range.

Looking to give your VSR-10 platform Sniper rifle a bit more range? The CYMA Upgrade set for CM.7061/VSR-10 will give you what you seek, with the added benefit of including reinforced parts! The set includes the piston, piston head and spring guide, all of which are machined from aluminium and finished in metallic blue, and a seriously high power spring which gives out approximately 575 FPS when installed! This set is compatible with most VSR-10 clone sniper rifles, including the JG BAR-10, CYMA CM.701 and the Well MB02/03/05/07/10.

If you want to tighten your groupings and get maximum accuracy from your GBB or VSR setup, the Maple Leaf 2023 Decepticon HOP-up Bucking for VSR/GBB is the HOP-up rubber you need! Also known as the "Desepticons" bucking by Maple Leaf, this is the 2023 version with a refined shape and packaged with an air-seal promoting C-ring which also enhances feeding reliability. Compatibility-wise, this bucking is designed for unbridged VSR-10 and GBB pistol inner barrels.

The Decepticon makes use of a flat shield-shaped contact patch and is ideally paired with a Maple Leaf I-Key but also works with standard HOP-up arms/tensioners. When compared to its sister bucking, the Autobot, the Decepticon is made for maximum accuracy with a slight range sacrifice while the Autobot is focussed purely on long range. If you're all about accuracy, the Maple Leaf 2023 Decepticon HOP-up Bucking for VSR/GBB belongs in your build!

If you have a sniper rifle project on the go and your base gun is a Maruzen APS2 Type 96 clone, an FPS Softair Upgrade Spring will be very useful! These springs are designed for the Maruzen APS2 Type 96 pattern of L96 Airsoft sniper rifle (Well MB01, Well MB08 etc) but won't fit the more recently designed Tokyo Marui L96 pattern or the AGM 002 L96.

FPS Softair offers a wide range of springs, so no matter what power level you are seeking, they have you covered! Options include M90 and M100 for low-velocity setups focussed on easy cocking, low wear and quiet muzzle report and M120 or M140 options for those who want to push their power level up for better range.

If your priority is extending range and you run a GBB pistol or VSR-10 platform sniper rifle, the Maple Leaf 2023 Autobot HOP-up Bucking is calling your name! Also known as the "Aotubot" by Maple Leaf, this bucking is designed for pure range, with a shield-shaped contact patch for maximum contact area with your BBs and an impressive HOP-up effect. Being the 2023 model, this set also includes an air-seal promoting C-ring which also helps improve feeding. Compatibility-wise, this bucking is designed for unbridged VSR-10 and GBB pistol inner barrels.

Naturally, the Autobot is designed for use with heavy BBs (0.28g+) and is ideally paired with a Maple Leaf I-Key but works fine with standard HOP-up arm/tensioner setups. When compared to its sister bucking, the Decepticon, the Autobot is made for pure range and the Decepticon is for tighter groupings at shorter ranges. If you need maximum range, you need the Maple Leaf 2023 Autobot HOP-up Bucking for VSR/GBB!

If your priority is extending range and you run a GBB pistol or VSR-10 platform sniper rifle, the Maple Leaf 2023 Autobot HOP-up Bucking is calling your name! Also known as the "Aotubot" by Maple Leaf, this bucking is designed for pure range, with a shield-shaped contact patch for maximum contact area with your BBs and an impressive HOP-up effect. Being the 2023 model, this set also includes an air-seal promoting C-ring which also helps improve feeding. Compatibility-wise, this bucking is designed for unbridged VSR-10 and GBB pistol inner barrels.

Naturally, the Autobot is designed for use with heavy BBs (0.28g+) and is ideally paired with a Maple Leaf I-Key but works fine with standard HOP-up arm/tensioner setups. When compared to its sister bucking, the Decepticon, the Autobot is made for pure range and the Decepticon is for tighter groupings at shorter ranges. If you need maximum range, you need the Maple Leaf 2023 Autobot HOP-up Bucking for VSR/GBB!

An upgrade hop bucking for Tokyo Marui and other compatible products. Designed for the Tokyo Marui VSR-10 bolt action and blow back pistols in mind including the Hi-Capa 4.3, Hi-Capa 5.1, M1911A1, SIG P226, SOCOM MK23 and G26. 

An Alloy constructed Trigger Set for the WELL MB Series of Spring-Powered Sniper Rifles, which is designed as a drop-in unit to replace a damaged Trigger. The part is very easy to install and is a great way to bring your MB-01/MB-08 back to life with minimal fuss, should it be suffering from a Trigger fault.

If you're seeking maximum HOP-up performance and are committed to using heavy BBs, the Maple Leaf 2023 MR HOP Bucking for VSR/GBB belongs in your build. The MR HOP-up Bucking offers a wider and longer “R-HOP” style contact patch for increased HOP-up effect and extended range with heavy BBs. The MR HOP also uses a shield-shaped groove around the contact patch to allow it to stretch and add to the strong HOP-up effect along with an air seal improving C-ring which ensures the bucking is firmly fitted to the barrel and unable to slip or rotate.

MR stands for “Maximum Range”, a design based on home-brewed R-HOP buckings, intended to prioritise range over grouping size and is best used paired with a Maple Leaf OMEGA or OHM HOP-up nub. Compatibility-wise, this version of the MR HOP is designed for unbridged VSR-10 and GBB pistol inner barrels but as always, a certain amount of expertise and tuning may be required to install it, though it will be far less work than the R-HOPs of old!

If you're seeking maximum HOP-up performance and are committed to using heavy BBs, the Maple Leaf 2023 MR HOP Bucking for VSR/GBB belongs in your build. The MR HOP-up Bucking offers a wider and longer “R-HOP” style contact patch for increased HOP-up effect and extended range with heavy BBs. The MR HOP also uses a shield-shaped groove around the contact patch to allow it to stretch and add to the strong HOP-up effect along with an air seal improving C-ring which ensures the bucking is firmly fitted to the barrel and unable to slip or rotate.

MR stands for “Maximum Range”, a design based on home-brewed R-HOP buckings, intended to prioritise range over grouping size and is best used paired with a Maple Leaf OMEGA or OHM HOP-up nub. Compatibility-wise, this version of the MR HOP is designed for unbridged VSR-10 and GBB pistol inner barrels but as always, a certain amount of expertise and tuning may be required to install it, though it will be far less work than the R-HOPs of old!

If you're seeking maximum HOP-up performance and are committed to using heavy BBs, the Maple Leaf 2023 MR HOP Bucking for VSR/GBB belongs in your build. The MR HOP-up Bucking offers a wider and longer “R-HOP” style contact patch for increased HOP-up effect and extended range with heavy BBs. The MR HOP also uses a shield-shaped groove around the contact patch to allow it to stretch and add to the strong HOP-up effect along with an air seal improving C-ring which ensures the bucking is firmly fitted to the barrel and unable to slip or rotate.

MR stands for “Maximum Range”, a design based on home-brewed R-HOP buckings, intended to prioritise range over grouping size and is best used paired with a Maple Leaf OMEGA or OHM HOP-up nub. Compatibility-wise, this version of the MR HOP is designed for unbridged VSR-10 and GBB pistol inner barrels but as always, a certain amount of expertise and tuning may be required to install it, though it will be far less work than the R-HOPs of old!

If you're seeking maximum HOP-up performance and are committed to using heavy BBs, the Maple Leaf 2023 MR HOP Bucking for VSR/GBB belongs in your build. The MR HOP-up Bucking offers a wider and longer “R-HOP” style contact patch for increased HOP-up effect and extended range with heavy BBs. The MR HOP also uses a shield-shaped groove around the contact patch to allow it to stretch and add to the strong HOP-up effect along with an air seal improving C-ring which ensures the bucking is firmly fitted to the barrel and unable to slip or rotate.

MR stands for “Maximum Range”, a design based on home-brewed R-HOP buckings, intended to prioritise range over grouping size and is best used paired with a Maple Leaf OMEGA or OHM HOP-up nub. Compatibility-wise, this version of the MR HOP is designed for unbridged VSR-10 and GBB pistol inner barrels but as always, a certain amount of expertise and tuning may be required to install it, though it will be far less work than the R-HOPs of old!

If you are looking to extend the range of your L96 bolt action sniper rifle this is what you will need! A complete package including an aluminium spring guide, piston, piston head and spring for any APS2 L96 compatible Sniper rifle.

Looking to give your M24 platform Sniper rifle a bit more range? The CYMA Upgrade set for CM.702/M24 will give you what you seek, with the added benefit of including reinforced parts! The set includes the piston, piston head and spring guide, all of which are machined from aluminium and finished in metallic blue, and a seriously high power spring which gives out approximately 575 FPS when installed!

This set is compatible with most M24 sniper rifles based on the Classic Army design but is designed for the CM.702 series, and may need modification and tuning for other M24 platforms.

A replacement Bolt Assembly for the DBoys Shell Ejecting KAR98K Spring Powered Sniper Rifle, which is the easiest and most efficient way to repair a Rifle with a damaged action.

A highquality replacement Hop-Up unit designed and created by Action Army to fit TM Spec VSR / BAR-10 Airsoft Bolt Action Sniper Rifles, to enhance and perfect the performance of the weapon.

If you're experiencing feeding issues with your S&T Lee Enfield No.1 MK.III, this should cure it! The Loading Plate for S&T Lee Enfield No.1 MK.III Rifles is an original replacement part, constructed from high density polymer. The set includes the loading plate itself and its C-clip retainer and is confirmed to be compatible with the S&T Lee Enfield No.1 MK.III but compatibility with S&T's No.4 MK.I rifle is yet to be confirmed. 

Whether you've been unlucky and broken your loading plate or want to get ahead of a potential future failure, the S&T Loading Plate for S&T Lee Enfield No.1 MK.III Rifles is ideal!

LAYLAX - PSS10 VSR10 Spring - is a spring designed by LAYLAX for VSR bolt action sniper rifles and other compatible platforms.

If you're looking to give your CM.700/700A/708 sniper rifle a bit more range the CYMA spring upgrade set will be what you're after, with the added benefit of including reinforced parts! The set includes the piston, piston head and spring guide, all of which are machined from aluminium and finished in metallic blue, and a seriously high power spring which gives out approximately 575 FPS when installed!

For the smoothest and strongest bolt pull for your Tokyo Marui, CYMA or JG VSR-10 Pro and G-Spec sniper rifles. 

If you have an SSG 69 or M40A3, it's time to give it a bit more range, accuracy and power!

A spare or replacement Outer Shell for the Bolt Assembly of the Double Bell / D-Boys Kar98K Airsoft Shell-Ejecting Spring Sniper Rifle. If you own one of these Rifles then it is important to have spares of the part that handles most of the stress. Don't get caught out with a broken Rifle, have you spares drawer stocked up today!

Looking to give your CM.706 Sniper rifle a bit more range? The CYMA Upgrade set for CM.706 will give you what you seek, with the added benefit of including reinforced parts! The set includes the piston, piston head and spring guide, all of which are machined from aluminium and finished in metallic blue, and a seriously high power spring which gives out approximately 575 FPS when installed!

If you want to squeeze a bit more range from your CM.703 or CM.707 sniper rifle this upgrade kit will do it! The CYMA Upgrade Kit For CM.703/707 Sniper Rifle includes an aluminium piston, aluminium ball bearing spring guide and M175 main spring which should provide approximately 575 FPS with a 0.2g BB when installed in a rifle with good air seal.

As always, we recommend checking the FPS/joule limits of your local site before installing the spring, but the piston and spring guide can be used with the standard spring in your rifle to provide improved strength and long-term durability if your site limits your rifle to 500 FPS.

If you've got feeding issues with your TAC-41 or you broke the feed ramp, the Silverback Airsoft Feeding Ramp Gen 2 for TAC-41 Sniper Rifle will get you up and running again. This is the Gen 2 feed ramp, boasting an improved design which prevents breakages when the magazine is loaded incorrectly. Compatibility wise, this feed ramp is only for the Silverback Airsoft TAC-41 sniper rifle series but should fit all variants. 

If your Lee Enfield is out of action, hopefully, this will cure it! The S&T Loading Ramp for SMLE NO.1 MK.III S.M.L.E Bolt Action is constructed from high density polymer with steel screws and is a replacement original part for the S&T S.M.L.E spring bolt action rifle. This is the part that transports the BBs from the magazine into the HOP-up chamber, known as the "Loading Ramp", and is a common part which gets worn down over time. Whether your Enfield needs fixing or not, this is a great part to have in the tool box!

Next level of Airsoft sniper rifle hop-up rubber produced with similar materials and processes to Madbull's current line up of AEG hop-up components. 

If you want to push your VSR-10-based sniper rifle to the absolute pinnacle of accuracy, a TDC mod should do the trick! The Hades Airsoft TDC HOP-up Unit Set for VSR-10 Sniper Rifle is designed to replace the original HOP-up arm and adjuster, providing direct pressure to the top of the HOP-up nub and bucking to eliminate side-to-side shot deviation.

Installing this TDC unit will require some extensive, irreversible modifications to your base sniper rifle, so we only recommend this set for those who are confident with power tools and have a decent level of Airsoft technical knowledge.

The unit requires you to drill a hole through the top of your outer barrel using either a 5mm or 5.5mm drill bit and the included drill guide, inserting the guide into the stripped outer barrel to ensure the hole is drilled in the right place. Hades also recommends that when the modification is complete, that you glue the TDC unit to your outer barrel using super glue or another strong adhesive.

If you are the type of sniper that likes to get their hands dirty with modifications and you want your VSR to outrange and outshoot the rest, this kit will do it!

A Steel trigger sear set for the L96 series of Airsoft Sniper Rifles / Bolt action Rifles. Once fitted into your Airsoft Gun this steel sear set will provide you with a tough and reliable bolt retain so you can rack your gun in confidence and spend less time worrying about parts breaking and more time getting your head in the game!

Fine-tune your SSG10 with this Weight-Adjustable Piston from Novritsch, designed to enhance the performance of your SSG10 sniper rifle. Crafted with high-quality materials, this piston is the ultimate upgrade for tuning your SSG10 to make it shoot exceptionally with your different BB weights, barrel lengths, and the other interchangeable elements of your rifle.