VAPEX Airsoft Batteries

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. Fitted with a deans connector for low resistance.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards and comes fitted with Deans connectors instead of the standard Tamiya for upgraded Airsoft Guns.

VP Racing are well known for their high quality and high performance batteries with this one being a crane form factor. The battery has a voltage of 7.4v, has a capacity of 1450mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery consists of two cells working in tandem, with each cell measuring 13x0.7x2cm each with a cable length of roughly 7.5cm of wire. The battery should fit in crane stock battery compartments such as M4s and some handguards and full stocks, but remember to measure up before hand!

A high quality 1300mAh 7.4V LiPo battery suitable for Airsoft and RC use - perfect for fitting down stock tubes and areas with a small amount of space.

A super thin triple crane stock 11.1v 1300mAh 25C LiPo, which features a Deans Connector instead of the standard Mini Tamiya. 

If you need a battery for your M4/AR-15 buffer tube or your top-wired AK AEG this should be perfect! The VAPEX 7.4v 1300mAh 20C LiPo Stick Battery measures 14 x 1.2 x 1.8cm approximately with a wire length of 9cm, making it a good fit in rear wired M4s with a buffer tube battery compartment, SMG-5K AEGs or AK AEGs in the top-wired configuration.

The pre-installed battery connector is the common mini-Tamiya type and the battery has a discharge rate of 20C, making it ideal for Airsoft applications but also useful for those needing a compact power source for electronics or R/C projects.

A 9.6v 1600mAh NiMh battery in stick configuration, often used within Airsoft AK AEGs. With a slow charge you can expect up to a whole day of Airsoft action from one charge.

If you need slim 7.4V crane stock LiPo for your crane stock or handguard battery compartment, the VP Racing 7.4V 1000mAh 20c LiPo Crane Stock Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and is comprised of 2 cells, each of which measures 11 x 1.5 x 0.5 cm. The wire length between the cells and connector is approximately 10cm, giving you a bit of flexibility to ensure the battery is installed properly. As always, we recommend measuring thoroughly to ensure it fits before ordering!

A large stick type battery, designed to output a high power for fast trigger response and rate of fire for up to three quarters of a day on a slow charge.

A high quality 1300mAh 7.4V LiPo battery suitable for Airsoft and RC use, coming fitted with an upgraded Deans Connector rather than the standard Mini Tamiya.

Those of you with limited battery space, this block battery is the one! The battery will fit near enough all AEG rifles and will be especially useful in rifles with PDW stocks. It has a voltage of 7.4v, a capacity of 2800mAh and a discharge 30C. The battery is connected to your AEG via the Deans connector, not to be confused with Mini-Tamiya connector, however, adaptors are available.

The battery measures 7.5x1.5x2.5cm with a cable length of roughly 4cm.

A 7.4v 1450mAh LiPo stick battery suitable not only for Airsoft but for RC vehicles and toys too.

A triple crane stock 11.1v 1450mAh 25C LiPo, which features a Deans connector instead of the standard small Tamiya.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, and is designed to give you a high output for fast rate of fire and trigger response for roughly half a day dependent on trigger happiness.

A 7.4v 1450mAh LiPo stick battery with Deans connectors, suitable for Airsoft in addition to other application such as RC vehicles and toys too.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. 

If you're looking for an 11.1V LiPo which fits neatly into an AR buffer tube, this is the one! The VP Racing 11.1v 1450mAh 25C LiPo Stick Battery (Deans) measures approximately 13 x 2.3 x 2.8 cm with 8cm of wire length, making it great for buffer tubes and other cramped but relatively long battery compartments. As always, make sure you measure your battery compartment before ordering to avoid disappointment!

If you've just bought a new battery that has a connector too big or too small for your Airsoft AEG then this item will resolve your problems. Check the "Special Instructions" section of the Full Description to ensure you get the correct converter for your needs!

A simple and cheap device that can detect if a LiPo cell is no longer safe to use, this save you a tidy fortune by alerting you when a battery is going to die! 

A high output VP Racing 11.1v 1450mAh LiPo battery, designed to deliver some serious rate of fire and trigger response with the right setup.

If you're looking for an 11.1V LiPo which fits neatly into an AR buffer tube, this is the one! The VP Racing 11.1V 1300mAh 25c LiPo Stick Battery - Deans measures approximately 10.4 x 1.9 x 1.9 cm with 4cm of wire length, making it great for buffer tubes and other cramped but relatively long battery compartments. As always, make sure you measure your battery compartment before ordering to avoid disappointment!

A high quality and ultra compact 7.4v Lithium Polymer Battery with 850mAh of capacity, wth a 30C discharge rating.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, this variant of the battery is fitted with a Deans connector for upgraded Airsoft Gun connectors, rather than the standard Mini Tamiya.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!