- Programmable Trigger
- 'Speed Trigger' Included
- For Version 2 Rear Wired
A drop-in trigger, ETU & MOSFET for Version 2 compatible rear-wired Airsoft replicas, which includes features like a programmable trigger, low battery cutoff, shot sensor and comes included with a vertical 'speed trigger'.
Here at Patrol Base we ship all around world, with delivery not only to the UK, but to most of the EU and select Worldwide locations as well. We provide a working day by road service via our handpicked courier services, simply buy your Airsoft guns with us and we'll have them delivered directly to your door.
For more information and to see the country we deliver please check out our Delivery Information Page.
Below are some rough postage prices for orders. Please note these are subject to change, and are only a rough guide. For more accurate postage estimate please use the Postage Calculator at the basket.
UK Next Day
Highlands / Islands
* Please note that Scottish Highlands, Islands and EU post prices can vary wildly. Prices range from £8.99, up to £29.99, so please ensure you refer to the Postage Calculator at the basket for the lowest possible price.
We want you to be absolutely happy with our products and services, so we provide the simple Patrol Base guarantee: if on receiving your item you are unhappy with your item for any reason then simply send it back to us. We will replace or refund the item.
You can return any item for any reason whatsoever, even if you have just changed your mind, within 14 days of receipt of the order. This is in addition to your rights under the Consumer Protection (Distance Selling) Regulations 2000.
For more information on returning products, and how to do it please visit our Returns Policy Page.
This is a complete and ready to install Electronic Trigger Unit for Rear Wired Version 2 Airsoft gearboxes, and is the beating heart of what makes G&G ETU products so unbeatable on out-of-the-box performance. The package includes an Electronic Trigger Unit, which is a computer controlled trigger that allows you to program three round burst in a matter of seconds. This smart trigger unit also has a shot sensor which can detect a complete gear cycle, leading to more precise single shot and longevity of components. Also included in the package is a MOSFET which protects the eletrical components of your RIF and can detect a low voltage battery - cutting it off and stopping you from fully discharging a battery or ending up in a bad situation where your battery dies with a BB in the chamber and you are unable to remove it. The MOSFET also has a blade fuse wired in series with it. This kit comes included with a flat 'speed trigger' to finish off your ETU install, and to help you get the most benefits from your new trigger with a tighter response, and less pull required to get a shot off. This is the perfect kit for replacing a dead trigger unit in any G&G weapon, or for giving your old RIF a performance boost to bring it up to a modern spec.
- Known to be compatible with the following manufacturers:
- Tokyo Marui
- SRC (Requires slight modification to gearbox pin that locates and seats the trigger unit)
- Classic Army (APEX series may require light dremeling on inside of gearbox casing)
- 3 round burst option
- Hold trigger in 'Auto' for ten seconds to change between Auto/Burst
- Easy programming
- Heat shrink protected electronics
- Includes all parts required
- Shot completion - Returns your piston to the front of the gearbox after every shot
- Suitable for V2 gearboxes with up to 8mm sized bearings or bushings
- Tools not included
- Electronic Trigger Unit (ETU) & fitting screw
- Selector plate & spring
- MOSFET with fuse
- Motor wiring
- Signal wiring
Please note this unit best functions with an 11v LiPo battery. This installation is not recommended for a beginner Airsofter with limited internal parts knowledge. An 11v LiPo battery will cause strain and wear to other components considerably faster than using a 7.4 LiPo or 9.6v NiMh battery.
When installing please be extra careful when fitting the wiring, there is very little space for error. If you have 9mm bushings and bearings you may have to modify the provided selector plate. Please ensure your magazine and hop unit are empty of BBs before setting up 3-round burst or full auto cycle mode.
Due to the low voltage from different battery and/or motor specifications, it might cause an auto-semi problem. Please ensure you charge your batteries fully before use.
Internal Part Type
MOSFET, Trigger, Wiring,
Alloy, Polymer, Silicon
Internal Part Construction
Polymer, Alloy, Silicon,
Part for Power Source Type
Electric Part Specific
Gearbox Version Compatibility Variant
Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff.
Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.
We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!
Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.
Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.
If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.
For more information with fitting parts, or should you require help, feel free to get in touch with our Workshop Department via our Contact Us Page.