Airsoft Attachment & Accessory Discounts

If you want to equip your Cybergun CANIK TP9 GBB with a red dot optic for faster target acquisition and a slick modern look, the Cybergun CANIK Optic Plate & Charging Handle Set; Docter/RMR Footprint is designed for just that! This set includes two optics plates, one with an RMR footprint and one with a Doctor footprint, giving you access to the two most common red dot sight footprints.

Also included is a charging handle which can be attached to either side of the optic plate via its threaded base, granting functionality for both left and right-handed shooters and lightening fast handling IPSC race gun style! This is ideal for those who run their pistol as a primary in CQB skirmishes but can be left off entirely if you want a more snag-free setup well suited to a combat sidearm. If you want to dress your CANIK up like all the Glock and Hi-capa users can, here is your opportunity!

Those of you looking for a battery with a truly large capacity, you've come to the right place! The battery is perfect for larger battery compartments such as SMG-5, G3, M16 and AK platforms with fixed stock battery compartments. The battery has a voltage of 7.4v, a capacity of 2800mAh and a continuous discharge rate of 25C with a maximum discharge rate of 50C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.

The battery measures 13x1.1x4.2cm with a cable length of roughly 10cm.

If you're looking for a new outer barrel to make your M4/AR-15 AEG reach the moon, the 5KU 18" Aluminium Barrel for M4/AR-15 AEG is a fantastic option. Constructed from aluminium with 14mm CCW male threading at the tip, this 18-inch outer barrel includes pin holes for mounting an M4/AR-15 front sight/gas.

The 5KU 18" Aluminium Outer Barrel for M4/AR-15 AEG has the standard Tokyo Marui AEG outer barrel fitting at the rear, meaning it should fit the vast majority of M4/AR-15 platform AEGs but won't fit NGRS M4s or GBBRs. Whether you're extending your barrel for the improved long-range effect or you just want your Airsoft rifle to look massive and intimidating, the 5KU 18" Aluminium Outer Barrel belongs on your M4 AEG!

If you are looking for a lightweight tactical flashlight with more of an integral look, the WADSN WML should fit the bill! The sleek design of the WML keeps the light tight into your weapon to minimise snags and its integral switch makes it great for compact weapons with less rail space. The WML is designed with a wide variety of modes to choose from, and an integral Picatinny mount with spring loading to guarantee a tighter fit even on off-spec rails. This flashlight provides both momentary and constant on, as well as a stroboscopic mode to dazzle the enemy and give you a few extra moments to get the kill as you clear rooms in CQB.

A complete upgrade Cylinder set for AEGs which includes: Cylinder, Piston, Cylinder Head, Piston head and Nozzle. Improve your air seal and shot for shot efficiency today for improved range and accuracy.

A complete upgrade Cylinder set for AEGs which includes: Cylinder, Piston, Cylinder Head, Piston head and Nozzle. Improve your air seal and shot for shot efficiency today for improved range and accuracy.

If you're having issues with your AEG, and being able to pull the trigger in safe then it is likely your safety lever is bust! The G&G Armament Trigger Safety Lever For V2 Gearbox is the replacement part for you, a new safety lever will ensure that the trigger cannot be depressed while your AEGs safety is engaged.

This part is constructed from alloy and is compatible with all version 2 gearboxes. It includes the spring and the screw so you can install it all together. Be warned though, it can be a techy repair and we only recommend that professionals attempt it!

This polymer constructed piece is designed to screw into your outer barrel assembly, to lock your Inner Barrel in place and removing any motion that is is able to have. This will help improve accuracy and consistency by stopping the inner barrel from wobbling as the BB travels through it. There is an option available for most major platforms, and is an absolute must-have piece for those seeking perfection in their rifles.

This polymer constructed piece is designed to screw into your outer barrel assembly, to lock your Inner Barrel in place and removing any motion that is is able to have. This will help improve accuracy and consistency by stopping the inner barrel from wobbling as the BB travels through it. There is an option available for most major platforms, and is an absolute must-have piece for those seeking perfection in their rifles.

The G&G Armament G2 Tappet Plate For V2 AEG is a reinforced AEG Tappet Plate for use with version 2 gearboxes. It is specially formulated to be strong yet flexible enough to bend slightly. The plate is constructed from extremely lightweight polymer and is designed to be attached to the air nozzle and sector gear. This process controls the feeding of BBs from the magazine into the hop up chamber.

It is compatible with almost every Version 2 gearbox on the market and comes with only the tappet plate.

An Airsoft Magazine designed for use with Tokyo Marui's Recoil Shock Airsoft TM 417 6mm BB Guns. The magazine is constructed entirely from Heavy Duty Polymer, and features a Transparent Black Shell allowing the user to see through to the Internal Mock rounds which add Realism to the Magazine.

If you have worn out your AEGs trigger or you want the mil-spec look to replace your current trigger, this is perfect for you! The G&G Armament Trigger For V2 Gearbox is constructed from alloy with a textured finish and is patterned after the standard curved "Milspec" trigger found on the M4A1 rifle, MK18 MOD.0 and MOD.1, along with most other M4/AR-15 rifles used in military service in the real world.

The trigger is compatible with version 2 gearboxes which are found in the vast majority of M4/AR-15 AEGs. This means that the G&G Armament Trigger For V2 Gearbox trigger should work in practically any M4/AR-15 AEG but will require the gearbox to be opened for installation.

If you need a battery for a fixed stock or other large battery compartments this one should fit the bill! The 7.4V 1800mAh 20C Block LiPo Battery from Electro River is the perfect battery for full stocks found on M16, AK, SMG-5 and G3 Airsoft AEGs. The battery measures 10 x 1.2 x 3.5cm approximately with a wire length of around 9cm and is pre-wired to a mini-Tamiya battery connector.

The battery is a 7.4V 2-cell battery in block configuration with a continuous discharge rate of 20C and a maximum discharge rate of 40C, making it great for almost any Airsoft AEG, though make sure you measure before ordering!

If you've had a cut-off lever failure or you like to keep parts on hand just in case the worst happens, the G&G Armament Cut Off Lever For V2 Gearbox is perfect. This is a replacement original part constructed from alloy, compatible with most version 2 gearboxes on the market.

The cut-off lever is a piece that sits between your trigger and sector gear and serves to interrupt or disconnect the trigger once your gearbox has made a complete cycle, very useful!

A replacement side mount plate for CMYA AK47/74 series Airsoft AEG weapons, which when fitted allows users to install AK style side-mounted scope mounts.

Next level of Airsoft sniper rifle hop-up rubber produced with similar materials and processes to Madbull's current line up of AEG hop-up components.

A Full Polymer constructed Mid-Cap Magazine for the G&G branded G36 series AEGs. Perfect for those who want to inject more realism into their play-style.

The WADSN DBAL Mini is a compact laser aiming module with two fully adjustable lasers combined into a single unit! The DBAL-Mini from WADSN provides both a red visible laser and an IR laser which is only visible under night vision, both of which are zeroed together with common tool-less adjustment dials. This DBAL-Mini is the much sought after aluminium version and boasts more realistic construction than its polymer counterparts. If you own night vision of any kind, this laser is a must!

A replacement original KRYTAC part which fits version 2, 3, 6 and 7 gearboxes. This cylinder is a Type 1, meaning it has a port in the side intended to reduce the air volume for use on short barrelled platforms (<363mm inner barrel) and prevent the "suck back" phenomenon.

An 11.1v 2000mAh Li-Ion battery for Airsoft Electric Guns, which comes supplied in a Crane/Butterfly/Saddle configuration, meaning two rows of cells. This makes them very easy to place in awkard-to-fit spots such as Handguards and Crane Stocks, and will provide better Power Density that traditional LiPo batteries.

A 530 round high capacity, wheel-wound magazine, designed for use with G&G's UMG SMG electric replica. Constructed from durable, high strength and lightweight polymers.

The Angry Gun QDC 3-Prong Flash Hider matches the design of real steel flash hiders such as the ones found on AUGs. It is constructed from steel making it extremely durable and sure to withstand any skirmish. This muzzle device is designed to work with other Angry Gun QDC attachments such as their suppressor and tracer unit. These products interlock seamlessly guaranteeing a reliable attachment every time.

This flash hider mounts to 14mm CCW threading, commonly found on most Airsoft assault rifles. It also has a grub screw so you can ensure it is securely attached to your replica with no worries about it coming off. The flash hider also comes with a stainless steel shim, to make sure that it is situated perfectly on your rifle's outer barrel.

If you want a super realistic flash hider that is compatible with Angry Gun QDC suppressors and tracers, this is the one for you! Its steel construction and real steel design certify that this flash hider is perfect for any skirmisher seeking a realistic loadout.

An AEG cylinder head for version 2 gearboxes found in M4/AR15 AEGs and SMG-5 AEGs. This KRYTAC part features a dampening pad, intended to reduce the noise from the piston impacting the cylinder head and give you a smoother sounding gearbox. The cylinder head is constructed from high density polymer with a brass inner nozzle and a rubber dampening pad.

This spare magazine for the G&G Armament Piranha gas blowback Airsoft pistol is constructed with a transparent polymer shell with mock 9x19mm cartridges visible within, and is a great way to make your pistol stand out on the field. It is filled with BBs using a speedloader, preferably with a GBB adapter, and can be filled with gas using the fill valve on the baseplate. If you own a G&G Piranha Pistol, then Spare Magazines are an absolute must for staying in the field longer and avoiding the long walk back to the safe zone to reload!

Looking for some extra firepower for your TM NGRS AEG? The NUPROL 1200rnd Electric drum magazine is the key to gaining the volume of fire advantage when skirmishing, and is the perfect tool to repel an ambush. This drum magazine is constructed from high-density polymer with a modern design aesthetic, and is the first of its kind for the NGRS system! If the "normal" AEG users are getting on your nerves with their high-caps, pull this bad boy out of the kitbag to remind them who is the boss!

Please note, this drum magazine is NOT compatible with standard M4/AR-15 AEGs and only works with Tokyo Marui NGRS (Next Generation Recoil Shock) AEGs.

The STTI B9/B92 Conversion Kit is a Polymer constructed Body Kit for... you guessed it, B9 and B92 Airsoft Gas Blowback Pistols. This awesome kit will convert your lowly Airsoft Pistol into a functional Carbine with Sliding Stock, 20mm Rail System, Ambidextrous Charging Handle as well as plenty of room for a Suppressor, Inner Barrel Extension or Tracer Unit!

An efficient and well-constructed Air Nozzle which is available for a wide range of replicas, and ensures improved durability and smooth operation.

A green gas magazine designed for the ICS BLE-XFG range of pistols. Holds up to 19 rounds

A  Full polymer constructed High Cap Magazine for the G&G branded G36 series AEGs. Perfect for those who want to spends more time shooting rather than reloading.

A 6mm BB Airsoft magazine, designed for use with Tokyo Marui's SMG-7 AEP electric Airsoft Submachine gun, featuring a medium capacity of 50 rounds.