Airsoft Boneyard

This beautiful replica has found its way into our boneyard due to its front sight being damaged - as far as things go, that's pretty much it for this replica. Externally it's in excellent condition apart from scuffs suggesting it was handled in our showroom as a display piece so we can safely assume it hasn't been shot at all apart from our own testing and going through factory QC. 

Firing through our chronograph gave us a rough reading of 300 FPS on .2 BBs using Nuprol 2.0 Green Gas however it seemed that the replica struggled to fire the entire mag before gassing out; you may have to purge the magazine when you receive it or it could be a completely different issue which will require investigation. Switching to Vorsk V8 gave us the same results although obviously being a little snappier at first.

These CYMA/EMG CM.102 SGR-12 Tri-Shot Shotguns found their way to the Boneyard due to generally poor quality control. These are brand new guns, unused and never shot but we can make no guarantees of proper functionality. As with all Boneyard items, these do not have a warranty and are sold as spare parts, wall hangers or props.

For a detailed product description and more specifications, click HERE to view the original product.

This replica has landed in our boneyard due to the magazine release missing its spring. We're unsure how this has occurred but if you're wanting to use this replica for skirmish, it would be ideal to find the replacement part for the magazine catch - that's if the replica even works as we're unable to test for further faults as the battery and battery charger are nowhere to be seen. Alongside this, the magazine is also missing so a replacement mag would also have to be sourced. Ignoring these issues, this could be quite a good prop or parts donor as the replica is in good condition externally with marks that are barely visible.

This replica has landed in our boneyard for unknown reasons - as far as things go, we cannot test for any sort of fault that this replica may or may not have due to the charger and battery being missing. Given this situation; if there is faults then ultimately this replica may be more suitable as a prop for cosplay or even a parts donor. Alongside this, the magazine is missing so a replacement should be sourced. The grip panel is also falling off so would require a bit of TLC to make it ideal as a prop.

This replica has landed in our boneyard for unknown issues - as far as things go, we cannot test this replica due to the battery and battery charger not being present so for this reason we cannot guarantee that the replica will turn up to you either functional or non-functional. Even then, this replica can happily serve as a prop or even as a parts donor.

This replica has landed in our boneyard for unknown issues - as far as things go, we cannot test this replica due to the battery and battery charger not being present so for this reason we cannot guarantee that the replica will turn up to you either functional or non-functional. Even then, this replica can happily serve as a prop or even as a parts donor.

This replica has found its way into our boneyard due to the magazine latch not being present - the entire latch alongside the spring is missing meaning the magazine may have fallen out during use as that isn't present either. Alongside these issues, the charger and battery are also missing so replacements are to be sourced if you're wanting to use this replica if it's functional which we cannot test given we have no battery to verify if there's any faults present. This replica may better suit being a parts donor given the already missing parts and uncertainty of functionality though could also be suitable as a prop for cosplay.

This replica has landed in our boneyard for unknown issues - as far as things go, we cannot test this replica due to the battery and battery charger not being present so for this reason we cannot guarantee that the replica will turn up to you either functional or non-functional. Even then, this replica can happily serve as a prop or even as a parts donor.

This replica has landed in our boneyard for unknown issues - as far as things go, we cannot test this replica due to the battery and battery charger not being present so for this reason we cannot guarantee that the replica will turn up to you either functional or non-functional. It also seems this replica needs a bit of TLC as there's various marks and scratches across the slide and frame albeit hard to see. Even then, this would be decent as a prop for cosplay.

This replica has found its way into our boneyard for a few reasons - first of which is part of the housing that holds the spring for the external hammer has broken which means the slide cannot be secured in place since this is what holds the slide and frame together. Alongside this, the replica is missing its battery and charger meaning we cannot test for any faults and to see if the replica is functional so you'll have to prepare for this if you source replacements. If the replica is non-functional, it could work as a prop for cosplay or even be a parts donor if it is functional.

This replica has landed in our boneyard due to a few issues - first of which is that the tabs that secure the slide in place have snapped off completely meaning theres nothing to secure the slide and will fall off during use. Alongside this, it's missing its battery and battery charger so we cannot test its functionality so you could ultimately end up with a perfectly fine replica or something that needs some work doing to it internally. Apart from this; the replica used to be two-tone red but the paint was stripped - there is still residue red paint under the slide alongside in the serrations so this replica does need a bit of TLC.

This replica has found its way into our boneyard due to it being partially disassembled and missing parts - it seems majority of the missing parts are found in a bag contained within the box the replica came with however we're not sure if there are parts still missing. Apparently the trigger bar is broken too which will require further investigation. The magazine and suppressor are also missing so replacement should be sourced unless you're wanting a cosplay/prop item which this would be perfect for (or even as a wall hanger).

This replica has ended up in our boneyard due to an issue regarding the trigger - as far as we can tell, the trigger return spring is weak and half the time you will fail to reset it whilst firing but shouldn't be too much of an issue if you let go of the trigger after each shot. Other than this, the replica is fully functional albeit the performance is sub-par where we were seeing lows of 220 to highs of 340 but got an average overall of 270 FPS on .2 BBs using Nuprol 1.0 White Gas.

This replica has landed in our boneyard for unknown reasons - as far as things go, we cannot test for any sort of fault that this replica may or may not have due to the charger and battery being missing. Given this situation; if there is faults then ultimately this replica may be more suitable as a prop for cosplay or even a parts donor.

This replica has landed in our boneyard due to a portion of the slide being chipped off - we're unsure how this has happened but ultimately doesn't affect functionality. Regarding function, we're unable to test for internal issues due to the battery and charger going missing so we cannot guarantee that the replica can actually shoot or has some weird electronic issue - if this is the case, this replica could ultimately serve as a parts donor or as some sort of prop.

This replica has found its way into our boneyard due to a few issues; first and foremost, the trigger seems to be broken as there's no spring tension - pulling the trigger all the way back whilst a battery is plugged in also provides nothing so whatever linkage/contacts are present is potentially also broken. The left side tab to keep the slide on the replica is broken as well though the right tab is still in one piece so you'll have to be careful when using this replica - keep in mind that you will need to source a battery and charger if you are wanting to use this replica since both are missing.

This replica has found its way into our boneyard due to the rear slide tabs breaking off completely - due to this fault, the slide freely comes off and isn't secure so you will have to replace the appropriate parts in order to bring this replica back to its former glory. Despite this, the replica is still fully functional when held together manually; firing at 235 FPS on .2 BBs. The charger and battery are also missing so these would have to be sourced in order to use this replica.

This replica has landed in our boneyard due to a few issues; the most concerning is when inspecting the battery connector, it appears to have melted/burned in some sort of fashion so this could mean a few things - most likely is that the electronics/mosfet is faulty and was drawing too much power. Alongside this issue, the magazine, charger and battery are also missing so these would also have to be sourced. We believe this replica would better suit being a prop for cosplay or something similar given the mentioned issues.

This replica has found its way into our boneyard due to potential mosfet issues - during testing, we didn't find anything obvious that pointed towards a faulty mosfet though performance was slightly sluggish per trigger pull in regards to the replica cycling. Firing through our chronograph, we were seeing 205 FPS on .2 BBs so you could happily skirmish this AEP indoors without problem. Take note that this replica is missing its battery and charger so both would require a replacement to be sourced in order to use the platform.

This replica has landed in our boneyard due to apparently not being able to cycle - through our own testing however, the replica seems to be fully functional minus a slightly sluggish performance. Firing through our chronograph, we were seeing 200 FPS on .2 BBs so it's more than capable to be used during a skirmish. We will note that the magazine alongside the charger and battery are all missing so replacements will have to be sourced in order to use this replica.

This replica has found its way into our boneyard due to issues with the trigger being 'stiff' - testing this, it does appear that there's a little more resistance than normal when pulling the trigger but still feels normal for an AEP. Other than this, the replica is fully functional and we were seeing 220 FPS on .2 BBs although performance was slightly sluggish. Alongside the issue addressed, the battery and charger are missing so replacements will have to be sourced in order to use this replica.

This replica has landed in our boneyard due to supposedly being dead - however when we did our testing, the replica seems to be functional albeit slightly sluggish in trigger response and general performance. Regardless, we were seeing 215 FPS on .2 BBs so if you want a capable AEP that probably just needs a bit of TLC then this may be the one for you; take note that the battery and charger are missing so these would have to be sourced.

This replica has landed in our boneyard due to supposed electrical issues - further inspection presents us with a replica that has a strong odor emitting from it, suggesting the internals may be burned out. We're reluctant to test the replica due to the damaged connector which also looks like it's discoloured, which makes us believe that the electronics have burned out and subsequently caused the wiring to warm up (which can kill/damage any battery connected). Ultimately this replica is usable as a wall hanger or as a prop provided these issues have ended up killing-off the replica - adding on that the magazine is nowhere to be seen alongside the charger and battery also not being present.

This replica has landed in our boneyard due to issues regarding the selector - as far as we can tell, the physical selector isn't able to interact with the internals of the replica in order to change to semi-auto which means this replica is primarily an outdoor platform unless you want a beautiful sidearm as a prop or wall hangar. Other than this issue, we were seeing an average of 210 FPS on .2 BBs which is normal for an AEP platform like this one. Do note that this replica out of the box is missing its charger and battery so a replacement would have to be sourced.

This replica has landed in our boneyard due to being partially disassembled - we can only presume that a part has been broken and the replica was disassembled to remove the part to eventually replace it however this may have not happened and has been kept in pieces. Based on the fact that the slide is missing, we're assuming this was the broken part and ultimately this replica would need a replacement to re-assemble.

Included in the box is a bag of parts which visually inspecting it, shows us a BBU housing, nozzle, what appears to be the take-down lever and some sort of rod. Other that was was explained, there may be other faults that we can't test for so this would require some serious tech work in order to get it back into its former condition.

This sniper rifle has landed in the Boneyard due to missing parts and being semi-disassembled. The handguard is missing and a bag of parts is included in the box. The bolt mechanism is functional but due to the front end missing, we were unable to test the platform.

It's a great bargain for some spare parts to make repairs or to potentially salvage the bolt system and insert it into another frame. It comes with a magazine and the aforementioned bag of pieces, presumably recovered from the missing front end.

This replica has landed in our boneyard due to an issue regarding the slide - as far as we can tell, it appears the slide is warped outwards on the right side of the part. This is an issue as it disengages/detaches itself from the runners on the frame so we'd rather not test the replica in the chance that the slide will fully come off and launch back at the shooter. Otherwise the rest of the components look to be in good condition so you could potentially use this as a parts donor or even as a prop/wall hanger. We did notice a small part in the box though we're unsure what this is for.

This replica has found its way into our boneyard for unknown reasons - one thing that we can be sure about is the entire slide and magazine are missing; the only remaining parts from the slide is the outer barrel, hop unit and recoil spring. Other than this, the slide itself, recoil spring buffer/spacer and BBU components alongside the housing. Since the slide is missing, if your own EU17 is experiencing trigger issues then this may be perfect as a parts donor since as far as we can tell; the trigger group seems to be mechanically fine.

This replica has found its way into our boneyard due to missing various components which renders the replica unusable. It appears that the barrel assembly including the recoil set, some frame parts and trigger as well as potentially some fire group components are all missing. Visually inspecting the frame indicates that the safety (or part of the housing that holds it) is broken but that's isn't too much of an issue given the safety itself is missing so in general this replica is massively in disrepair and missing the majority of parts. 

It seems if the trigger as well as its linkage was to be sourced that the fire group could potentially work but we cannot guarantee anything. Ultimately this replica would be best suited as a parts donor (the magazine is also missing so you'll be getting this replica purely for the internal components most likely).

This gas powered FABARM shotgun has a jammed pump. We're unsure on the root cause or any potential fixes to this issue, but you unfortunately won't be able to rack it. A unique platform, this one will be well worth your time to fix up, or could serve well as a display piece/prop.