LiPo Batteries

If you're looking for an 11.1V LiPo which fits neatly into an AR buffer tube, this is the one! The VP Racing 11.1V 1300mAh 25c LiPo Stick Battery - Deans measures approximately 10.4 x 1.9 x 1.9 cm with 4cm of wire length, making it great for buffer tubes and other cramped but relatively long battery compartments. As always, make sure you measure your battery compartment before ordering to avoid disappointment!

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, and is designed to give you a high output for fast rate of fire and trigger response for roughly half a day dependent on trigger happiness.

A triple crane stock 11.1v 1450mAh 25C LiPo, which features a Deans connector instead of the standard small Tamiya.

If you need a battery for your M4/AR-15 buffer tube or your top-wired AK AEG this should be perfect! The VAPEX 7.4v 1300mAh 20C LiPo Stick Battery measures 14 x 1.2 x 1.8cm approximately with a wire length of 9cm, making it a good fit in rear wired M4s with a buffer tube battery compartment, SMG-5K AEGs or AK AEGs in the top-wired configuration.

The pre-installed battery connector is the common mini-Tamiya type and the battery has a discharge rate of 20C, making it ideal for Airsoft applications but also useful for those needing a compact power source for electronics or R/C projects.

A high quality 1300mAh 7.4V LiPo battery suitable for Airsoft and RC use - perfect for fitting down stock tubes and areas with a small amount of space.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, this variant of the battery is fitted with a Deans connector for upgraded Airsoft Gun connectors, rather than the standard Mini Tamiya.

VP Racing are well known for their high quality and high performance batteries with this one being a crane form factor. The battery has a voltage of 7.4v, has a capacity of 1450mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery consists of two cells working in tandem, with each cell measuring 13x0.7x2cm each with a cable length of roughly 7.5cm of wire. The battery should fit in crane stock battery compartments such as M4s and some handguards and full stocks, but remember to measure up before hand!

If you're looking for the very smallest of LiPo batteries, you've found it. Measuring 4x1.3x2cm, this battery can be used to power the FCU in the V12 engine, in addition to other HPA systems with a mini-JST type connector.

The battery has a voltage of 7.4v, a capacity of 250mAh and a discharge rate of 20C and features a cable length of roughly 10.5cm

If you need a compact 11.1V LiPo for your buffer tube, PDW stock or other cramped battery compartment, the VP Racing 11.1V 800mAh 20c LiPo Stick Battery should do the trick. This 11.1V 3S LiPo stick battery is fitted with a Deans battery connector and measures 10.4 x 1.7 x 1.9 cm with 4cm of wire length, making it suitable for upgraded Airsoft AEGs, even those with small battery compartments. As always, we recommend measuring thoroughly to ensure it fits before ordering!

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. Fitted with a deans connector for low resistance.

This LiPo battery from Gens Ace is designed to fit into compact and slim battery compartments, such as the M4/AR15 buffer tube and the AK47/74 top cover. The battery connects to your AEG via a Deans connector (AKA T-Plug) and provides 1400mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8.5cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

A high quality 1300mAh 11.1V LiPo battery suitable for Airsoft and RC use. A single stick type battery that will fit into most Airsoft AEG hand guards or stocks and stock tubes.

A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.

A stick battery designed for most M4 stock tubes, solid stock sand some hand guards. An ideal starter LiPo which you should get half a days use out of at least from a slow charge.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

A high voltage Airsoft Battery designed to give your weapon the highest rate of fire possible, in addition to lasting as long as possible, reducing the amount of time players spend changing batteries on a Skirmish day. 

A 7.4v 1450mAh LiPo stick battery suitable not only for Airsoft but for RC vehicles and toys too.

A high quality 800mAh 11.1V LiPo battery suitable for Airsoft and RC use. This is a single stick type battery will fit into most Airsoft AEG hand guards or stocks and stock tubes.

If you're looking for a tiny LiPo battery for your Novritsch SSE18 or CYMA CM.1xxS MOSFET equipped AEP, this is what you need. The Novritsch 7.4V 600mAh LiPo Battery measures approximately 7.3 x 1.5 x 1cm and is pre-wired with a Mini-Deans battery connector and a 3 port balance connector. 

As with other LiPo batteries, this battery should only ever be charged on a LiPo balance charger, preferably in a battery charging bag and should not be left on charge unattended under any circumstance.

A high output VP Racing 11.1v 1450mAh LiPo battery, designed to deliver some serious rate of fire and trigger response with the right setup.

If you are heavy on the trigger with your LiPo ready AEP you might need a couple of these! The IPower 7.4V 680mAh 20c LiPo battery is just like a normal LiPo stick, but much much smaller. This battery is designed as a spare battery for the CYMA CM.xxxS series of LiPo-ready AEPs and is pre-wired to a mini-Deans connector. This battery can be charged like a normal LiPo battery; using the balance lead and with a LiPo balance charger. This battery cannot be charged with a normal NiMh/NiCad charger, do not attempt it as you may cause a fire. If you are the creative type this battery's minuscule form could lend itself well to an electronics project or R/C use.

A high powered Airsoft Battery, designed to be used in highly tuned top-end gearbox. The battery comes in a 'stick' configuration, with two adjoined cells in one block, allowing the battery to be squeezed into even the tightest of buffer tubes. 

Those of you looking for a battery with a large capacity in a medium-sized block form factor, you've come to the right place! The battery is perfect for larger areas such as full-stocked SMG-5, G3, M16 and AK platforms, AR36 handguards and full-stock rifles. The battery has a voltage of 7.4v, a capacity of 2300mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.

The battery measures 10x1.5x3.4cm with a cable length of roughly 10cm.

A large 11.1v VP Racing 2600mAh LiPo with a small Tamiya connector designed for a full days Airsoft action with impressive rate of fire and single shot results.

A super thin triple crane stock 11.1v 1300mAh 25C LiPo that features a standard Tamiya connector and is made up of three individual thin cells, making it great for squeezing into awkward spaces.

A compact yet high output LiPo battery designed for most M4 stock tubes, solid stocks and some hand guards.

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

If you need a battery to fit into a tight place, Evolution Airsoft have you covered with the 7.4V 1100mAh 20C LiPo Stick Battery. This battery comes pre-wired with a Deans battery connector, also known as a "T-Plug" but is packaged with a Deans to mini-Tamiya adapter, meaning it can be used with almost any Airsoft AEG around.

The battery is a 2 cell 7.4V LiPo battery in stick configuration, meaning the cells are bound together into a single unit. The wire length between the battery and connector is approximately 10cm, the continuous discharge rate is 20C and the peak discharge rate is 40C. Whether you need a battery for your Airsoft gun or another electronics hobby which requires a compact power source, this Evolution Airsoft battery will do the trick!

If you need an Airsoft battery that fits in almost anything and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo/ LiFe/NiMH Balance Charger, a Safe Charging Bag and an ASG 7.4V 1300mAh LiPo Battery in Crane configuration with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs and capable of fitting inside Crane stocks, fixed stocks and most handguards! If you have multiple different AEGs and you want a battery to fit them all, chances are this one will! 

The dimensions of the included battery are as follows: 10.1cm x 0.7cm x 2cm per cell group (2x cell groups on each battery) with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Crane Stock, M4/AR-15, SMG-5 & AK Fixed stock, AR-36 & SMG-5 handguards, Tokyo Marui SCAR-L/H NGRS stock, most M4/AR-15 buffer tubes. 

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery with a Mini-Tamiya connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a buffer tube battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 1.3cm x 1.5cm with approximately 9cm of wiring between the battery and connector