Airsoft Pistol Magazines

A must have set for any Airsofter and Air Pistol Dan Wesson Revolver owner.

An Airsoft 6mm BB gas blowback magazine for the 5.1 Hi-Capa pistol series, with a double stacked design it has a capacity of up to 25 bb rounds. 

A spare magazine for WE Europe 1911 Airsoft pistols. The magazine is constructed entirely from Alloy, with the only Polymer parts being the feed lips and follower.

Looking for spare mags for your Spicy Vorsk VX26 GBB? Here they are, with a whopping 30 round capacity and a nice polymer baseplate to protect the magazine from accidental drops. This magazine is for use with green gas and is loaded through the feed lips at the top or by pulling the follower down and loading though the widened section of the follower channel. You can use either a speed loader or do it by hand, though we advise the former if you're in a hurry!

If your 1911 Pistol had an underwhelming performance in the cold weather, you need a CO2 magazine and the performance will be much better! CO2 is much better in cold weather and yields a far, stronger recoil, meaning gassing out is a thing of the past! Also remember that CO2 does not contain any lubricant of its' own, and so you will need to lubricate your Pistol regularly using a Silicon Lubricant, such as:Abbey Silicone Gun Oil 35 Spray.

Just remember that the laws of physics still apply, and if you try to dump an entire Magazine quickly, you could cause damage to the Nozzle of your Pistol. Please ensure that all CO2 has been used in the Magazine before attempting to remove the Bulb, as it could still be under pressure. Excess CO2 is best used by firing the Pistol, rather than pressing the knocker valve on the back of the Magazine.

Keep your 1911 performing well no matter the weather with the WE 15rnd CO2 Magazine for 1911 GBB Pistols, come rain or snow your 1911 will still be able to complete the mission.

This magazine is specifically for the STTI ST92F, in that this is a non-blowback mag and features incredible gas efficiency. The magazine is constructed from high high-density polymer and is incredibly lightweight compared to tis alloy counterparts. The magazine holds 23 rounds, filled at the top using a speed loader and the gas is filled at the bottom with green gas.

A gas blowback Airsoft CO2 magazine developed by VORSK for their Hi-Capa Series range of pistols, constructed with an Alloy Body and Polymer base plate. The magazine is of standard length and holds 23 rounds and is a direct replacement for the magazine which comes with the pistol. The mag is filled with BBs from the top or front and CO2 bulbs can be installed through the side of the shell and tightened using the included Allen key, through the baseplate.

If you're looking to bolster your VORSK Hi-Capa Series pistol with 100% compatible magazines then this is the way to go. Particularly useful for the winter months, using CO2 should reduce the effect of cooldown on your pistol!

A 22 round Green Gas / Inlet Valve Magazine for the UMAREX Glock 45 Gas Blowback Pistol, featuring a top of the range build quality & official Glock trades. 

If you plan to run your Tokyo Marui Hi-Capa GBB on HPA, the Army Armament HPA Adapter for M4/AR-15 AEG Magazines; GBB Hi-Capa will considerably improve your firepower!

This HPA adapter is designed for the Tokyo Marui Hi-Capa GBB series and may fit Hi-Capa clones based on the TM design, though we can't make any guarantees. It allows standard M4/AR-15 AEG mags to be used along with a High-Pressure Air (HPA) power source, so you can kiss goodbye to the "cooldown" effect and limited magazine capacity if you're rocking this on your Capa!

The set includes an EU and US HPA connector but you will need an airline, HPA bottle and regulator to run this adapter. The advantages of using HPA when performance is concerned include the elimination of FPS fluctuation due to the "cooldown" effect, resulting in improved shot-to-shot consistency and improved accuracy down range, especially under rapid fire. If you're taking your playstyle in a speedy direction, this adapter will take your gameplay to the next level!

A Co2 Powered Gas Blowback Airsoft Pistol Magazine designed for use with the NUPROL RAVEN Range of MEU 1911 Pistols. An alternative to the Green Gas model of the magazine, and packs a much more powerful punch.

Looking for a CO2 magazine for your SRC Hi-capa to see it through the winter months? You have found what you need! This 28rnd CO2 Magazine is designed for the SRC Hi-capa GBB series, including the Baba Yaga and Kikimora pistols. The magazine can be loaded either through the feed lips or by dragging the follower down to the bottom and loading through the bottom of the feed channel.

This magazine houses a single unthreaded 12g CO2 capsule which can be loaded through the bottom of the magazine by removing the baseplate. If you want to guarantee your SRC Baba Yaga can hack it when the temperature gets low a CO2 mag is the perfect solution!

A 20 Round Green Gas Powered Magazine designed for the GLOCK 19X by UMAREX.

A 34rnd spare magazine for the CYMA CM.128 Hi-Capa styled Airsoft Electric Pistol, which will work with other CYMA AEPs but will extend beyond the baseplate depending on the model. It is filled from the top using a Speedloader to push BBs past the feed lips.

A spare or replacement magazine for Vorsk's VM9 GBB pistol. This magazine is constructed from alloy with a steel feed spring, polymer feed lips and brass valves. The magazine holds approximately 25 rounds and can be loaded either with a speed loader or by hand through the feed lips at the top, or the feed channel in the front. This magazine is suitable for summer gas, maintenance gas and green gas.

If you're looking to make the most of your SSP19's full-auto fire mode, one of these will do it! The Novritsch 23rnd TP22 / EU Green Gas Magazine is constructed from alloy. This green gas magazine can be filled through the fill valve on the rear of the magazine. This magazine is designed for

BBs are loaded either through the feed lips at the top or by holding the follower on the front down and filling through the widened section of the follower channel at the front. This is a great multipurpose magazine if you have a variety of pistols that you take to the battlefield.

If you're looking to make the most of your SSP19's full-auto fire mode, one of these will do it! The Novritsch 49rnd Extended Gas Magazine for SSP18 GBB is constructed from alloy and an extended design with a 49rnd capacity. This green gas magazine can be filled through the fill valve on the baseplate by inverting it, as you would with any other GBB mag. 

BBs are loaded either through the feed lips at the top or by holding the follower on the front down and filling through the widened section of the follower channel at the front. While it may be heavier and bigger than a standard mag, this is really the only way to do that rapid full auto mode justice!

An 8 round magazine for the SRC 7.65 pistol.

Many people convert their Hi-Capa pistols to HPA to reach a BB capacity close to this, well, don't they look silly now! This WE 350rnd Green Gas Drum Magazine allows you to fire 350rnds without being interrupted by having to swap magazines. No HPA modifications are needed, just a big old drum mag! It is designed for WE Hi-Capa pistols but may work with others, though compatibility cannot be guaranteed.

The magazine is constructed with a hefty alloy gas reservoir with a high-density polymer drum with rubber shock bumpers and an external winding wheel on the front which is easy to wind quickly with or without gloves. The sizeable gas reservoir of this magazine means in most cases you will easily be able to dump the full magazine without a refill, so if you want to run a pistol only this will provide you with more than enough firepower!

If you want to run your SSP18 or EU-series GBB on HPA, the Novritsch HPA SMG-5 Magazine Adapter for EU Series GBB Pistols; Gen 2 is the easiest way to do it. This adapter is pre-built using a zinc alloy magazine body and fibre-reinforced nylon polymer adapter and is outfitted for US Spec HPA lines by default. This adapter is designed to feed from curved MP5/SMG-5 AEG mid-cap magazines and HPA from an external tank (not included), increasing capacity considerably and practically eliminating FPS fluctuation due to the "cooldown" effect. 

The adapter is pre-assembled, meaning you don't need to mess around putting it together or run the risk of doing it wrong and causing injury. Naturally, you'll need an HPA bottle, air line and regulator to use this adapter and the fitting is US Spec, meaning only US Spec air lines will fit. If you're running your SSP18 in the Novritsch Minimalist Carbine Kit or as a primary, the Novritsch HPA SMG-5 Magazine Adapter for EU Series GBB Pistols; Gen 2 will give you the rapid-fire performance and capacity you need to stay ahead!

If you need mags to keep up with your SSP28's insane rate of fire, these are the ones! Patterned after real steel Glock mags with a +2 round extension, the Novritsch 30rnd SSP28 Green Gas Magazine is made with an alloy shell, polymer feed lips, a polymer baseplate, brass valves, a rubber gas route bucking and rubber O-rings.

The fill valve is located on the baseplate, and to fill it with gas, you will need to invert the mag and your gas can, as is the case with other GBB pistol mags. Loading BBs can be done either through the feed lips on the top or through the widened follower channel on the front by pulling down the follower. Please note, this magazine is only compatible with the SSP28 GBB and won't fit the SSP18, TP22 or any other EU series GBB we have tested.

If you run your Hi-Capa as a primary and find yourself short on ammo, the 44rnd Extended Hi-Capa Magazine for R501/R603/R604 GBB Pistols will keep you shooting for longer! This extended green gas magazine is compatible with Army Armament Hi-Capa GBB pistols but should also fit most Tokyo Marui-based Hi-Capa clones. This is the chrome silver version, ideal for the stylish skirmisher. If you need the black version, check it out here!

Constructed from alloy with a CNC aluminium baseplate and polymer feed lips, loading this mag is the same process as any other GBB pistol magazine; use a speed loader or loading tool and load either through the feed lips on top or by pulling the follower on the front down and loading through the widened section. Filling the amply-sized gas reservoir is equally easy; simply invert the magazine and gas canister and press the nozzle of your canister into the fill valve on the bottom of the mag.

If you use your Hi-Capa as a primary for CQB or like to keep a stendo on hand for emergencies, the Army Armament 44rnd Extended Magazine for R501/R603/R604 GBB Pistols will be a useful addition to your kitlist!

A gas blowback Airsoft CO2 magazine developed by VORSK for their VX-9 and MEU range of pistols, constructed with an Alloy Body and Polymer base plate. The magazine is of standard magazine length, holds 21 rounds and is a direct replacement for the magazine which comes with the pistol. The magazine can be filled with BBs from the top or front, and CO2 bulbs can be installed through the side of the shell and tightened using the included Allen key, through the baseplate.

If you're looking to bolster your VORSK VX-9 or MEU pistol with 100% compatible magazines then this is the way to go. Particularly useful for the winter months, using CO2 should reduce the effect of cooldown on your pistol!

One magazine probably isn't going to be enough for a pistol that has you wanting to keep shooting. This heftily constructed M9A3 magazine holds 22 rounds and takes 12g CO2 bulbs, with a beautiful matt tan finish to match your pistol and also the real deal!

If you're planning to run your EU series, AAP-01 or Lancer Tactical CTHULHU on HPA, the Lancer Tactical HPA Adapter for M4/AR-15 AEG Magazines; EU Series & AAP-01 will do the trick! This HPA adapter is designed for EU series GBB pistols and should also fit the Action Army AAP-01 and Lancer Tactical's radical CTHULHU pistol. Designed to allow standard M4/AR-15 AEG mags to be used along with a High Pressure Air (HPA) power source, you can kiss goodbye to the "cooldown" effect and limited magazine capacity with this adapter on your gat!

The set includes both an EU and US HPA connector but you will need an airline, HPA bottle and regulator to run this adapter. The advantages of using HPA when performance is concerned include the elimination of FPS fluctuation due to the "cooldown" effect, resulting in improved shot-to-shot consistency and improved accuracy down range, especially under rapid fire. If you're taking your playstyle in a speedy direction, this adapter will change your game!

If you're planning to run your EU series, AAP-01 or Lancer Tactical CTHULHU on HPA, the Lancer Tactical HPA Adapter for M4/AR-15 AEG Magazines; EU Series & AAP-01 will do the trick! This HPA adapter is designed for EU series GBB pistols and should also fit the Action Army AAP-01 and Lancer Tactical's radical CTHULHU pistol. Designed to allow standard M4/AR-15 AEG mags to be used along with a High Pressure Air (HPA) power source, you can kiss goodbye to the "cooldown" effect and limited magazine capacity with this adapter on your gat!

The set includes both an EU and US HPA connector but you will need an airline, HPA bottle and regulator to run this adapter. The advantages of using HPA when performance is concerned include the elimination of FPS fluctuation due to the "cooldown" effect, resulting in improved shot-to-shot consistency and improved accuracy down range, especially under rapid fire. If you're taking your playstyle in a speedy direction, this adapter will change your game!

Need some big mags for your big handgun? The Cybergun Desert Eagle green gas magazine should do the trick! This magazine is designed for the Cyber Gun Airsoft Desert Eagle L6 GBB and holds approximately 27 BBs which can be loaded using a speed loader through the feed lips at the top of the magazine. This magazine is a green gas magazine and can be filled through the fill valve on the magazine's baseplate, and can also take summer gas to keep the FPS down to reasonable levels on hot days. The magazine is constructed from alloy with polymer feed lips, with a steel feed spring and brass valves, and has realistic mock witness holes on each side, matching the cut-outs in the real Desert Eagle magazine used for gauging how many rounds are left.

A replacement or spare Magazine for a RAVEN branded Hi-Capa 4.3 or 5.1. It holds a total of 25rnds and is powered by a 12g CO2 Bulb, which means it works far better in the cold than a Green Gas Magazine. This Magazine will provide much stronger recoil and better shots-per-magazine, especially when Winter is upon us.

This spare magazine for the G&G Armament Piranha gas blowback Airsoft pistol is constructed with a transparent polymer shell with mock 9x19mm cartridges visible within, and is a great way to make your pistol stand out on the field. It is filled with BBs using a speedloader, preferably with a GBB adapter, and can be filled with gas using the fill valve on the baseplate. If you own a G&G Piranha Pistol, then Spare Magazines are an absolute must for staying in the field longer and avoiding the long walk back to the safe zone to reload!

A 50rnd Extended Gas Magazine for a range of ASG Gas Replicas, including the B&T USW, the Shadow 2, SP-01 and CZ 75. If you own one of these replicas and want the ability to throw 50 BBs down range in a hurry, then the firepower increase of a 50rnd Magazine cannot be overstated.

A green gas magazine designed for the ICS BLE-XFG range of pistols. Holds up to 19 rounds