All Airsoft Batteries

A compact LiPo Airsoft battery, designed to be used in tight awkward spaces, without compromising on overall capacity.

A 7.4v 1500mAh LiPo battery that provides a 20c discharge rate and is highly compact, making it ideal for external PEQ battery boxes and tight, square spaces.

A high powered Airsoft Battery, designed to be used in highly tuned top-end gearbox. The battery comes in a 'stick' configuration, with two adjoined cells in one block, allowing the battery to be squeezed into even the tightest of buffer tubes. 

Suitable not only for Airsoft but for RC vehicles and toys too, this 7.4v 1550mAh LiPo Stick Battery will fit in tight areas like stock tubes and handguards where other batteries wouldn't normally.

A LiPo crane stock battery designed to fit in crane and solid stocks, where other batteries would be wasting the available space. 

A LiPo crane stock battery designed to fit in stocks and small spaces which other large batteries do not fit.

An 11.1v 1200mAh 20c LiPo Battery in a Slim Stick configuration, complete with a Deans Connector. It has total dimension of: 1.35cm x 1.62cm x 18.5cm and is perfect for up-rated guns and rifles with a high power draw such as DMRs and high rate of fire setups, and other replicas that require a Stick Battery down the Receiver, such as AK/UMP models.

If you need a compact 7.4V LiPo for your buffer tube, PDW stock or other cramped battery compartment, the VP Racing 7.4V 800mAh 20c LiPo Stick Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and measures 10.2 x 1.1 x 1.9 cm with 5cm of wire length, making it suitable for most Airsoft AEGs, even those with small battery compartments. As always, we recommend measuring thoroughly to ensure it fits before ordering!

A high quality and ultra compact 7.4v Lithium Polymer Battery with 850mAh of capacity, wth a 30C discharge rating.

If you're looking for a tiny LiPo battery for your Novritsch SSE18 or CYMA CM.1xxS MOSFET equipped AEP, this is what you need. The Novritsch 7.4V 600mAh LiPo Battery measures approximately 7.3 x 1.5 x 1cm and is pre-wired with a Mini-Deans battery connector and a 3 port balance connector. 

As with other LiPo batteries, this battery should only ever be charged on a LiPo balance charger, preferably in a battery charging bag and should not be left on charge unattended under any circumstance.

A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.

An 11.1v 1200mAh 20c LiPo Battery with a Deans Connector in a Stick configuration, making it ideal for Solid Stocks and some rear wired Buffer Tubes. It has the following dimensions with a 9cm cable: 2cm x 1.63cm x 13cm.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

A LiPo crane stock battery designed to fit in crane and solid stocks, where other batteries would be wasting the available space. 

A LiPo battery with a universal electric pistol connection that will allow it to be used in pretty much every Airsoft Electric Pistol we can think of.

Suitable not only for Airsoft but for RC vehicles and toys too. This Stick Battery is relatively large and excellent for ensuring you get a full day's play out of one charge, providing you're not too trigger happy.

If you need a battery for your M4/AR-15 AEG Crane stock and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configuration with a Deans connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2 cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

An ultra-thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c. The battery is so thin it can fit into stock tubes and AK/MP5 AEG Battery compartments.

Those of you looking for a battery with a large capacity in a medium-sized block form factor, you've come to the right place! The battery is perfect for larger areas such as full-stocked SMG-5, G3, M16 and AK platforms, AR36 handguards and full-stock rifles. The battery has a voltage of 7.4v, a capacity of 2300mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.

The battery measures 10x1.5x3.4cm with a cable length of roughly 10cm.

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

An ultra thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 30c. Being short and wide, this battery is perfect for PEQ boxes and solid stocks.

A crane stock Lithium Polymer (LiPo) type battery, which allows for the best possible power to size ratio and charge life available in a compact battery.

A compact 7.4v two cell stick battery that is ideal for squeezing into small spaces like stock tubes, especially the battery spaces on Honey Badgers and compact weapons with an extending skeleton stock.

A 7.4v Lithium Polymer Battery designed for use in battery compartments with limited space for a thin, but long battery.

If you need a compact block battery for a handguard or fixed stock with limited space this should do the trick! The 7.4V 1500mAh 20C LiPo Block Battery from Electro River measures 8.5 x 1.2 x 3.4cm approximately with a wire length between the cell group and connector of approximately 9cm.

The pre-wired connector is the Deans/T-plug the continuous discharge rate is 20C and the maximum is 40C, making this battery great for both Airsoft applications and electronics hobbies.

A humungous 7.4v LiPo battery in a Crane Stock / Nunchuck configuration which offers a massive 3000mAh capacity. If you want the biggest battery you can possibly squeeze into your replica, this is probably it!

A super thin triple crane stock 11.1v 1300mAh 25C LiPo that features a standard Tamiya connector and is made up of three individual thin cells, making it great for squeezing into awkward spaces.

Giant Power are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 35C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery's dimensions are 7x1.5x3.4cm with a cable length of roughly 7.5cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.

This 11.1v 1300mAh 15C LiPo Stick Battery is a high quality battery suitable for Airsoft and RC use. Being a single stick type this battery will fit into most Airsoft AEG hand guards or stocks and stock tubes.

If you need an Airsoft battery that fits in almost anything and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo/ LiFe/NiMH Balance Charger, a Safe Charging Bag and an ASG 7.4V 1300mAh LiPo Battery in Crane configuration with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs and capable of fitting inside Crane stocks, fixed stocks and most handguards! If you have multiple different AEGs and you want a battery to fit them all, chances are this one will! 

The dimensions of the included battery are as follows: 10.1cm x 0.7cm x 2cm per cell group (2x cell groups on each battery) with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Crane Stock, M4/AR-15, SMG-5 & AK Fixed stock, AR-36 & SMG-5 handguards, Tokyo Marui SCAR-L/H NGRS stock, most M4/AR-15 buffer tubes.