All Airsoft Batteries

A Pack of two CR123A batteries that are used to power most Airsoft accessories. The battery provides 3V of power, and 1400mAh of charge.

If you're looking for the very smallest of LiPo batteries, you've found it. Measuring 4x1.3x2cm, this battery can be used to power the FCU in the V12 engine, in addition to other HPA systems with a mini-JST type connector.

The battery has a voltage of 7.4v, a capacity of 250mAh and a discharge rate of 20C and features a cable length of roughly 10.5cm

A stick battery designed for most M4 stock tubes, solid stock sand some hand guards. An ideal starter LiPo which you should get half a days use out of at least from a slow charge.

A high quality and ultra compact 7.4v Lithium Polymer Battery with 850mAh of capacity, wth a 30C discharge rating.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

A high voltage Airsoft Battery designed to give your weapon the highest rate of fire possible, in addition to lasting as long as possible, reducing the amount of time players spend changing batteries on a Skirmish day. 

A 7.4v 1450mAh LiPo stick battery suitable not only for Airsoft but for RC vehicles and toys too.

If you're after a safer alternative to a LiPo power source with no sacrifice in trigger response or rate of fire, the 9.6V 1600mAh NiMH Crane Stock Battery from Big Foot is ideal. An 8-cell NiMH battery pre-wired to a mini-Tamiya battery connector, this battery is configured in two cell groups, known as a "nunchuck" or "crane stock" battery. This allows it to fit into the cheek pieces of the common crane stock and other similar stocks like the Delta Armory Stock and the PTS EPS Stock.

As with any NiMH battery, this battery should only be charged on compatible NiMH chargers and never left attended while on charge. We also recommend charging any battery in a Battery Safe Charging Bag just in case. Being a 1600mAh battery, this should power almost any mini-Tamiya connector-equipped AEG for several hours of intense gameplay, though if you're out in the field all day, we recommend grabbing a second to stay in the fight for longer!

If you need a compact Airsoft battery which fits almost anywhere the 7.4v 1100mAh 20C LiPo Crane Battery from VAPEX is ideal. This battery is pre-wired with a mini-Tamiya battery connector and each cell unit measures 11 x 0.7 x 2.2 cm with approximately 9 cm of wiring between each cell and the connector, making it great for tight spaces and use with multiple different platforms.

The compact size of this crane/nunchuck battery makes it ideal not only for Airsoft but also for electronics hobby applications and R/C when a lightweight and compact power source is a priority. Whether it needs to fit into a buffer tube, crane stock, handguard or practically anywhere else this super slim battery is perfect, especially if you want a single battery which fits in multiple guns!

A high quality 800mAh 11.1V LiPo battery suitable for Airsoft and RC use. This is a single stick type battery will fit into most Airsoft AEG hand guards or stocks and stock tubes.

If you're looking for a tiny LiPo battery for your Novritsch SSE18 or CYMA CM.1xxS MOSFET equipped AEP, this is what you need. The Novritsch 7.4V 600mAh LiPo Battery measures approximately 7.3 x 1.5 x 1cm and is pre-wired with a Mini-Deans battery connector and a 3 port balance connector. 

As with other LiPo batteries, this battery should only ever be charged on a LiPo balance charger, preferably in a battery charging bag and should not be left on charge unattended under any circumstance.

A high output VP Racing 11.1v 1450mAh LiPo battery, designed to deliver some serious rate of fire and trigger response with the right setup.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A large 11.1v VP Racing 2600mAh LiPo with a small Tamiya connector designed for a full days Airsoft action with impressive rate of fire and single shot results.

A super thin triple crane stock 11.1v 1300mAh 25C LiPo that features a standard Tamiya connector and is made up of three individual thin cells, making it great for squeezing into awkward spaces.

A high powered Airsoft Battery, designed to be used in highly tuned top-end gearbox. The battery comes in a 'stick' configuration, with two adjoined cells in one block, allowing the battery to be squeezed into even the tightest of buffer tubes. 

If you are heavy on the trigger with your LiPo ready AEP you might need a couple of these! The IPower 7.4V 680mAh 20c LiPo battery is just like a normal LiPo stick, but much much smaller. This battery is designed as a spare battery for the CYMA CM.xxxS series of LiPo-ready AEPs and is pre-wired to a mini-Deans connector. This battery can be charged like a normal LiPo battery; using the balance lead and with a LiPo balance charger. This battery cannot be charged with a normal NiMh/NiCad charger, do not attempt it as you may cause a fire. If you are the creative type this battery's minuscule form could lend itself well to an electronics project or R/C use.

A compact yet high output LiPo battery designed for most M4 stock tubes, solid stocks and some hand guards.

A four pack of AAA batteries rated at 1.5v - ideal for a wide range of Airsoft accessories and remotes as well as other hobbies like RC Cars, Boats and Planes.

The perfect battery to give you enough juice for a full weekend of Airsoft milsim action. 9.6v and 4300mAh of power. Commonly used within M249, M16 and M14 variants.

A standard Alkaline 9v battery from VAPEX which can be used for a wide array of Airsoft accessories as well as other hobbies such as RC Cars, Planes, Boats and other DIY projects.

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

If you're after an 8.4V NiMh battery for a crane stock battery compartment, the GFC 8.4V 1600mAh Ni-Mh Crane Stock Battery; Mini Tamiya is ideal. A 7-cell rechargeable NiMh battery pre-wired to a mini-Tamiya battery connector, this Crane configuration battery is ideal for rear-wired M4/AR-15 AEGs with Crane stock battery compartments. Wire length is approximately 10cm, giving you a bit of extra flexibility for easy installation. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

This LiPo battery from Specna Arms is designed to fit into flat and long battery compartments, such as some handguards or crane stocks. The battery connects to your AEG via a Deans connector and provides 2000mAh capacity with a 15C discharge rating.

The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 10.5cm, allowing an easier fit into tighter spaces. The Specna Arms 11.1V 2000mAh 15C LiPo Nunchuck Battery; Deans would be great for any Airsoft gun which requires an 11.1V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

If you need a battery to fit into a tight place, Evolution Airsoft have you covered with the 7.4V 1100mAh 20C LiPo Stick Battery. This battery comes pre-wired with a Deans battery connector, also known as a "T-Plug" but is packaged with a Deans to mini-Tamiya adapter, meaning it can be used with almost any Airsoft AEG around.

The battery is a 2 cell 7.4V LiPo battery in stick configuration, meaning the cells are bound together into a single unit. The wire length between the battery and connector is approximately 10cm, the continuous discharge rate is 20C and the peak discharge rate is 40C. Whether you need a battery for your Airsoft gun or another electronics hobby which requires a compact power source, this Evolution Airsoft battery will do the trick!

If you need an Airsoft battery that fits in almost anything and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo/ LiFe/NiMH Balance Charger, a Safe Charging Bag and an ASG 7.4V 1300mAh LiPo Battery in Crane configuration with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs and capable of fitting inside Crane stocks, fixed stocks and most handguards! If you have multiple different AEGs and you want a battery to fit them all, chances are this one will! 

The dimensions of the included battery are as follows: 10.1cm x 0.7cm x 2cm per cell group (2x cell groups on each battery) with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Crane Stock, M4/AR-15, SMG-5 & AK Fixed stock, AR-36 & SMG-5 handguards, Tokyo Marui SCAR-L/H NGRS stock, most M4/AR-15 buffer tubes. 

If you need a battery for your top wired AK or SMG-5K AEG and would rather get everything you need in one place, here it is! This bundle includes a LE-3 LiPo Balance Charger, a Safe Charging Bag and a Giant Power 7.4V 1300mAh LiPo Slim Stick Battery with a Mini-Tamiya connector; an ideal setup for a mini-Tamiya equipped top wired AK or SMG-5K AEG with a battery compartment inside the receiver.  

The dimensions of the included battery are as follows: 18.5cm x 1cm x 2cm with approximately 9.5cm of wiring between the battery and connector. 

The perfect battery to give you enough juice for a full weekend of Airsoft milsim action. 9.6v and 3700mAh of power. Commonly used within M249, M16 and M14 variants.

An individual 3V Lithium Button Battery, which are commonly used in Airsoft Sights, Scopes and other Accessories. 

An 8.4V 1600mAH stick battery with a Mini-Tamiya connector which can be charged using a standard NiMH charger. This battery's stick configuration makes it ideal for folding stock AK type AEGs or others with a long, thin battery compartment.