- Fits Any AEG
- Ultra Compact
- Protects Trigger Contact
An ultra compact Generation 3 MOSFET built to be as compact as possible, requiring the smallest amount space possible, and is water resistant.
Here at Patrol Base we ship all around world, with delivery not only to the UK, but to most of the EU and select Worldwide locations as well. We provide a working day by road service via our handpicked courier services, simply buy your Airsoft guns with us and we'll have them delivered directly to your door.
For more information and to see the country we deliver please check out our Delivery Information Page.
Below are some rough postage prices for orders. Please note these are subject to change, and are only a rough guide. For more accurate postage estimate please use the Postage Calculator at the basket.
UK Next Day
Highlands / Islands
* Please note that Scottish Highlands, Islands and EU post prices can vary wildly. Prices range from £8.99, up to £29.99, so please ensure you refer to the Postage Calculator at the basket for the lowest possible price.
We want you to be absolutely happy with our products and services, so we provide the simple Patrol Base guarantee: if on receiving your item you are unhappy with your item for any reason then simply send it back to us. We will replace or refund the item.
You can return any item for any reason whatsoever, even if you have just changed your mind, within 14 days of receipt of the order. This is in addition to your rights under the Consumer Protection (Distance Selling) Regulations 2000.
For more information on returning products, and how to do it please visit our Returns Policy Page.
This MOSFET is designed to achieve a higher rate of fire and trigger response, as well as protects the mechanical trigger contacts by directly bypassing the contacts and going straight to the motor. The unit itself is so compact that it can be fit in any Airsoft AEG, allowing you to wire the unit in down buffer tubes and in tight hand guards. The package comes with everything you need to connect up the unit, with spare wires for different trigger setups. This is perfect for those Airsoft Players who want the absolute best out of their weapon, adding a features which improve the performance of Rifles.
- Battery Support: 7.2v LiPo, 11.1v LiPo, 12.8v LiFe, 8.4v NiMh, 9.6v NiMh
- Operating Ranges: 3v - 13v
- User Guide: picossr3_en.pdf
- 12 Months Warranty
- Ultra Compact Design
- 3rd Generation Mosfets
- Trigger Protecting MOSFET
- Smaller and more compact than over units on the market
- Increases the ROF of your AEG
- Provides a better Trigger Responce
- Resistant to Water Immersion
- Kit comes with all required parts
- Fits in any Airsoft AEG
- PicoSSR 3 AEG Micro Mosfet Unit
- Single Signal Wire for Trigger Contacts x2
Should you need any help installing the MOSFET please feel free to call our workshop on: 01484 644709.
Do not hold the Soldering Iron on the Unit for more than 3 seconds, as this will cause permanent heat damage to the MOSFET unit.
Please note that the warranty covers the unit from defects, not improper installation. Please read all user guides before installing.
Please remember when installing the device to ensure your AEG is clear before use,
Ensure that when wiring up the device the Positive and Negative battery terminals are the correct way around as this will cause immediate damage to the unit.
For warranty related issues please visit: http://gatee.eu/technical-support/warranty
Internal Part Type
Ultra Compact Circuit Board
Part for Power Source Type
Electric Part Specific
Gearbox Version Compatibility Variant
Most Airsoft AEG
Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff.
Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.
We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!
Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.
Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.
If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.
For more information with fitting parts, or should you require help, feel free to get in touch with our Workshop Department via our Contact Us Page.