Gate TITAN V2 NGRS Advanced Set
Gate
Product code:
£159.95
  • Complete TITAN Kit
  • Trigger Replacement
  • For NGRS Recoil System

A drop in MOSFET Kit designed for Tokyo Marui NGRS Recoil Shock Systems, such as the NGRS M4, and the NGRS SCAR. This variation of the Kit comes with the MOSFET Unit, the USB-Link, and is the Advanced version with unlocked features.

Full description

Description

The Titan is a complete trigger set replacement, with optical sensors instead of mechanical switches and has a high end software and sensor based sector gear detection, allowing some of the fastest and most efficient AEG builds. The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries. The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical, and has multiple on board Optical Sensors. The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and braking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. Once installed the MOSFET can be re-programmed via the Gate Configuration Card or via the USB-Link to a Windows based PC, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. What's important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well they have been implemented.

Features

  • Built in the EU
  • 12 Months Manufacturer Warranty
  • Complete Trigger Set replacement Kit
  • Built specifically for TOKYO MARUI NGRS Rifles
  • Supports:
    • Tokyo Marui M4 Next Generation
    • Tokyo Marui SCAR-H Next Generation
    • Tokyo Marui SCAR-L Next Generation
    • Tokyo Marui HK416D Next Generation
    • Tokyo Marui HK416C Next Generation
    • Tokyo Marui HK417 Next Generation
  • 3rd Generation Trigger sensor
  • 50 sensitivity levels for the first millimeter of trigger movement
  • 420 sensitivity levels for the trigger
  • Bolt catch sensor to support empty magazine detection
  • Designed for Highly Efficient AEG Builds
  • Suitable for Stock Guns and Upgraded Guns
  • Great for DMR and Standard Setups
  • Re-programmable with a the Titan Programming Card and USB Link
  • Optical Sensor Controlled
  • Multiple optical sensors
  • Replaces the Cut-off Lever
  • Compatible with most V2 Gearbox on the market without Modification
  • Auto-Adjusting Pre-cocking / Braking system
  • Works with Dual Sector Gear and Short Stroked Gears
  • Capable of Fast Repeat Shooting
  • MILSPEC Board coating
  • Adjustable Trigger Sensitivity
  • Adjustable Pre-cocking Boost
  • Adjustable Fire-Selector Mode
  • Adjustable Burst Mode
  • Adjustable Rate of Fire
  • Two-Stage Trigger Mode, Possible for Semi / Full Auto without using a Fire Selector
  • Sniper Delay Modes
  • Run-away Motor 30 Rounds Limit Mode
  • Protection for the Titan Unit against Over Current, Under Current, and Overheating 
  • Low Battery Warning
  • Over-discharge Battery Protection
  • Configurable Fire Selector
    • Safe - Semi - Auto
    • Safe - Semi - Semi
    • Safe - Semi - Burst
    • Safe - Burst - Auto
    • Safe - Semi - Burst / Auto (Short Press - Burst, Long Press - Auto)
    • Semi - Burst - Auto (Safe Mode via fast switch Safe - Semi - Safe)
  • Kit comes with required parts for Fitting (Please see Special Instructions)
  • Deans Connector Type
  • Protection for Li-Po, Li-Ion, Li-Fe, Ni-Cd Batteries
  • Optical Sensor Test Mode for easier Installation
  • Updateable Firmware via USB-Link on a Windows / MAC PC
  • Statistics and Additional Settings Accessible using a USB-Link with GATE-CS
  • Can be Diagnosed for Errors using the Programming Card or USB-Link
    • UVP1 – your battery is discharged
    • UVP2 – the voltage is lower than 3.8V
    • OCP1 – over current protection
    • OCP2 – the motor power supply circuit is shorted
    • OTP – the drop-in module temperature is too high
    • MOTOR DISC – you pulled the trigger but the motor did not move
  • Smart Fuse System

Package Includes

  • TITAN Drop In Module - Rear Wired
  • USB-Link
  • USB Cable
  • Quick start Guides
  • Installation Kit
  • TITAN Patch

Special Instructions

Please note that this version of the TITAN is designed for NGRS rifles only, and not for use in standard AEG gearbox.

Please note, this box contains the USB-Link, and everything you need to build and install the TITAN MOSFET.

Please only use either the Tactical Programming Card, or the USB-Link at any one time. Do NOT connect them both at the same time.

Should you need any help installing the MOSFET please feel free to call our workshop on: 01484 644709.

Please note that the warranty covers the unit from defects, not improper installation. Please read all user guides before installing, for more information please see the supplied Warranty Card.

Please remember when installing the device to ensure your AEG is clear before use.

Ensure that when wiring up the device the Positive and Negative battery terminals are the correct way around as this will cause immediate damage to the unit.

Please note, that battery protection is not compatible with Ni-Mh and Ni-Cd Battery

For warranty related issues please visit: http://gatee.eu/technical-support/warranty

The GATE Control Station Software can be downloaded at the following links:

Specification

General

Internal Part Type
MOSFET
Name Variant
Rear Wired, Front Wired,

Part Specific

Part for Power Source Type
Electric
Weapon Platform
  • Tokyo Marui NGRS Recoil System
  • Tokyo Marui NGRS Scar Recoil System

Size guide

Parts Fitting

Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff. 

Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.

We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!

Unique Parts

Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.

Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.

If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.