NUPROL 11.1v 1450mAh LiPo Nunchuck Battery (DEANS)

Code: 8124
  • Deans Connector
  • Crane Stock Layout
  • 11.1v 1450mAh 30C

A Lithium Polymer battery for Airsoft, RC Cars and many other hobbies which comes as a Crane Stock configuration with a Deans connector. This battery is perfect for rear wired Crane Stocks and front wired handguards, and especially AEGs that require an 11.1v battery.

Full description


This is a thin and compact butterfly battery which provides a tremendous amount of power in a small space, and will have no issue squeezing into the tightest of spots. It would ideally be suited for a rear-wired Crane Stock, front wired handguard or other battery compartment with a rough dimension of: 11.3cm x 2cm. These batteries are not only ideal for Airsoft skirmishers, but can be used in RC cars, toys, drones and other hobbies.


  • 11.1v 1450mAh
  • 30C rating
  • Long but thin LiPo
  • Compact dimensions
  • Tri-cell layout
  • Perfect for M4/15/16 Crane Stocks
  • Perfect for long but thin spaces
  • Ideal for front wired handguards
  • Deans connector

Package Includes:

  • 11.1v 1450mAh LiPo Nunchuck Battery
  • Instruction Manual

Special Instructions:

Please note that we only recommend that this battery be used in Highly upgraded guns, and as such we cannot provide a warranty on any gun which has had an 11.1v battery used on it. The only gun we recommend you use an 11.1v LiPo out of the box is the ASG - Scorpion Evo.

Please do not let the battery fully discharge before recharging, this will damage the battery, please use a LiPo Alarm to check the Charge of the Battery before use, and stop if the Rate of Fire Drops. To charge the battery you MUST use a Li-Po Battery Charger, as overcharging can cause damage to the unit.

Never leave Li-Po charging unattended - Always monitor the charging process of your Li-Po so that you can react immediately to any potential problems. If your batteries start to balloon or swell up discontinue charging / discharging. Before and after the use of your Li-Po batteries, inspect them to ensure there is no physical damage or swelling as those are signs of an imminent failure. 

Only use approved Li-Po chargers. Do not pierce or disassemble the battery. The charging current should not be ore than 1.0c as charging at a higher current may damage the cell or even lead to overheating or leakage. Stop charging immediately when temperature is over 45°C, and stop using the battery once the temperature is over 60°C.

We recommend that all LiPo batteries be charged in a fire resistant location, and inside a Fire Proof bag, such as the VP Racing Battery Giant Power LI-PO GUARD Charging Bag.



Product Length
Approx. 11.3cm
Product Height
Approx. 2cm
Product Width
Approx. 1.53cm
Weight KG Icon
Weight (KG)
Approx. 0.05kg
Patrol Base - Warning Icon
Li-Po - Never Leave Charging Unattended
Li-Po - Only Use Approved Chargers
Li-Po - Charge in a Fire Safe Area

Battery Specification

Battery Type
Battery Configuration
Battery Connector
Patrol Base | Icon | Deans
Battery Voltage
Battery Amperage
Battery Discharge Rate
Battery Cell Count
Battery Wire Length

Size guide

Airsoft Battery should only be charged with the chargers as they are specifically designed to work with the specific voltages required by the battery.

Different battery types have different chemical configurations, and require certain chargers to charge them. Charging a battery with the wrong charger can cause damage to the battery and charger, and can cause fires and further damage. Please ensure that before charging you double check that you are using the correct charger.

If your charger supports multiple battery types always ensure that it is on the correct settings before starting the charge.

If you are unsure of what battery or charger you have please get in touch with us via the Contact Us Page.

Need something to charge your LiPo?