All Airsoft Batteries

This LiPo battery from Specna Arms is designed to fit into crane stocks. The battery connects to your AEG via a mini-Tamiya connector and provides 2000mAh capacity with a 15C discharge rating.

The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 12cm, allowing some flexibility when squeezing the battery into tight spaces. The Specna Arms 7.4V 2000mAh 15C LiPo Nunchuck/Crane Battery; Tamiya would be great for any Airsoft gun which requires a 7.4V LiPo, but can also be used for other electronics hobbies.

If you're after an 8.4V NiMh for an AR36 or SMG-5 handguard battery compartment, the GFC 8.4V 1600mAh Ni-Mh Block Battery; Mini Tamiya is a perfect fit! A 7-cell rechargeable NiMh battery pre-wired to a mini-Tamiya battery connector, this Block configuration battery is ideal for fixed stock battery compartments, along with AR36 and SMG-5 handguard battery compartments. Wire length is approximately 10cm, giving you a bit of extra flexibility for easy installation. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

If you need a battery for a top-wired AK platform or an SMG-5K, this one is a perfect match! The Specna Arms 7.4V 1200mAh 20C LiPo Stick Battery (Mini-Tamiya) is designed for long, narrow battery compartments, measuring roughly 18cm x 1cm x 1.5cm, with an 11cm wire length, and comes pre-fitted with a Mini-Tamiya connector.

This 7.4V LiPo is made up of 2 cells combined into a single pack, delivering a 20C continuous discharge rate, 40C peak discharge, and a 1200mAh capacity.

This LiPo battery from Specna Arms is designed to fit into flat and long battery compartments, such as some handguards or crane stocks. The battery connects to your AEG via a Mini-Tamiya connector and provides 1300mAh capacity with a 15C discharge rating.

The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 10.5cm, allowing an easier fit into tighter spaces. The Specna Arms 11.1V 1300mAh 15C LiPo Nunchuck Battery; Mini-Tamiya would be great for any Airsoft gun which requires an 11.1V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

If you're looking for a battery for a top-wired AK setup or an SMG-5K, this battery is the perfect fit! Electro River 7.4V 1200mAh 20/40C LiPo Slim Stick Battery; Mini-Tamiya is ideal for long, slim battery compartments, measuring approximately 18.5cm x 0.8cm x 1.4cm with a 10cm wire length, and is pre-wired to a Mini-Tamiya connector. 

This 7.4V LiPo consists of 2 cells bound together into a single cell group, with a 20C continuous discharge rate, a peak discharge rate of 40C and a capacity of 1200mAh. 

This tiny Specna Arms 7.4V 1300mAh 30C Micro PEQ LiPo Battery is the best fit for a PEQ box wired gun, such as the Specna Arms SA-H01. It can squeeze into some tight spots, with its dimensions of 6.5x1.5x3.5cm; it will sadly not fit in PDW stocks, but may fit in some SMG and AR36 handguards.

As it is a 7.4V LiPo, it is compatible with almost every Airsoft gun, plus, its Deans-style connector is optimal as most modern Airsoft guns are coming with Deans connectors installed due to its lower electrical resistance when compared with Tamiya connectors. If you need a small battery for your Airsoft platform, the Specna Arms 7.4V 1300mAh 30C Micro PEQ LiPo Battery; Deans could be the best choice for you!

If you're running an M4 with a crane stock and need a longer-lasting battery, the GFC 9.6V 2200mAh Ni-Mh Nunchuck Battery; Mini Tamiya is a good shout. A battery of 8 cells formed into a single long cell group, this 9.6V rechargeable NiMh battery is a perfect fit for M4 AEGs with a Crane battery stock (or similar battery stock design) and also fits great in AEGs with fixed stock battery compartments (M16, etc.). Please note, to install this battery in a Crane Stock-equipped M4, you will need to place one of the cell groups inside the buffer tube. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

This LiPo battery from Specna Arms is designed to fit into flat and long battery compartments, such as some handguards or crane stocks. The battery connects to your AEG via a Deans connector and provides 2000mAh capacity with a 15C discharge rating.

The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 10.5cm, allowing an easier fit into tighter spaces. The Specna Arms 11.1V 2000mAh 15C LiPo Nunchuck Battery; Deans would be great for any Airsoft gun which requires an 11.1V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

If you have serious power demands and LiPo batteries don't cut it, Titan Power has you covered with the game-changing 7.4V 3000mAh Li-Ion Stick Battery; Deans Connector! Designed to fit into AR buffer tubes (some may require the stock to be extended), this power-dense Li-Ion battery has innumerable benefits over standard LiPos, including more robust steel-cased cells, larger capacity and no chance of swelling. 

Titan Power Li-Ion batteries can be charged through a standard LiPo balance charger using LiPo settings or with a B6-style smart charger (sometimes known as 4-button smart chargers) using "LiPo Balance" settings. Titan Power advise not charging using "Li-Ion" mode as this is generally intended for higher capacity batteries. 

As always, we recommend using a LiPo Safe Charging Bag for both charging and storage, and never leaving a battery on charge unattended. If you need a battery which will definitely keep your AEG going over long durations, the Titan Power 7.4V 3000mAh Li-Ion Stick Battery; Deans Connector is the best option out there!

If you're after an 8.4V NiMh battery for a crane stock battery compartment, the GFC 8.4V 1600mAh Ni-Mh Crane Stock Battery; Mini Tamiya is ideal. A 7-cell rechargeable NiMh battery pre-wired to a mini-Tamiya battery connector, this Crane configuration battery is ideal for rear-wired M4/AR-15 AEGs with Crane stock battery compartments. Wire length is approximately 10cm, giving you a bit of extra flexibility for easy installation. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

If you need a NiMh battery for a top-wired AK or SMG-5K/MP5K AEG, the GFC 9.6V 1600mAh Ni-Mh Stick Battery; Mini Tamiya is the way to go! A battery of 8 cells formed into a single long cell group, this 9.6V rechargeable NiMh battery is a perfect fit in AK AEGs with a battery compartment inside the dust cover or SMG-5K/MP5K AEGs with a battery housed inside the receiver. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

This ultra-thin Specna Arms 7.4V 1000mAh 30C Micro PEQ LiPo Battery is perfect for a PEQ box wired gun, such as the Specna Arms SA-H01. It can squeeze into some tight spots, but with its dimensions of 6.5x1x3.5cm, it will sadly not fit in PDW stocks but may fit in some SMG and AR36 handguards.

As it is a 7.4V LiPo, it is compatible with pretty much every Airsoft gun, and its Deans-style connector is optimal as most modern Airsoft guns are coming with Deans connectors installed due to its lower electrical resistance when compared with Tamiya connectors. If you need a teeny tiny battery for something, the Specna Arms 7.4V 1000mAh 30C Micro PEQ LiPo Battery; Deans could be your best shout!

If you're running a retro AEG and need a battery with a Large Tamiya connector, GFC has you covered! The 9.6V 2200mAh Ni-Mh Nunchuck Battery; Large Tamiya is an 8-cell NiMh battery wired in nunchuck configuration as two cell groups with 5cm of wire length between the cells and the pre-wired Large Tamiya connector. 

The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance charging, so you can use any charger as long as it's NiMh compatible. Just make sure not to leave the battery charging unattended, and as always, we recommend using a battery safe charging bag for both storage and charging. 

Ideal for fixed stock battery compartments but a bit too chonky for crane stocks, this battery is ideal for Cybergun FAMAS replicas or older TM AEGs with Large Tamiya connectors (TM M14, M16A1/A2, FAMAS, etc.). 

A LiPo Crane Stock battery designed to fit in stocks and small spaces which other large batteries do not fit. The battery is also know as a Nunchuck battery, with the cells connected via the wires allowing them to be placed down the side of barrels or in an M4 Crane Stock.

A LiPo stock tube battery designed to fit in buffer tubes and small spaces which other large batteries do not fit.

Need a battery and a charger for your upgraded AEG? Get both at once with the Specna Arms Set EASY Charger With an 11.1v 1000mAh Battery! This package has everything you need to get started with 11.1V batteries. The balance charger ensures that all your battery's cells are charged equally, it also works for 7.4V batteries.

11.1V batteries should only be used with upgraded platforms, the high voltage and discharge rate can cause excess wear on internal parts inside stock AEGs. However, if your Airsoft rifle is built to take 11.1V batteries you will notice an improved rate of fire, snappier trigger response and possibly even an increase in FPS.

An 11.1v 1450mAh 30C LiPo in a stick configuration, which features a Deans connector instead of the standard small Tamiya.

A ultra thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c, giving it a 20w output.

A High voltage Airsoft LiPo Battery designed to give your weapon the highest rate of fire possible, in addition to lasting as long as possible, reducing the amount of time players spend changing batteries on a Skirmish day. 

A Lithium Polymer battery for Airsoft, RC Cars and many other hobbies which comes as a Crane Stock configuration with a Deans connector. This battery is perfect for rear wired Crane Stocks and front wired handguards, and especially AEGs that require an 11.1v battery.

A stick 7.4v 1100mAh LiPo designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries, intended to allow Airsofters to get the best possible performance from their Airsoft Electric Guns.

A thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c and is so thin it can fit into stock tubes and AK/MP5 AEG Battery compartments.

A quality battery produced by VP Racing and designed for electronic products such as Airsoft AEG rifles and remote controlled cars etc. Holding a charge of 9.6V at 1600mAh, this battery will easily last all day of Airsoft gaming.

A 7.4v rated LiPo Battery for Airsoft Electric Guns, specifically ones that need a compact battery for a small space, such as PDW Stocks and Pistol Grips. The Battery has a 600mAh Capacity and a 20/40C Discharge Rate, as well as having a Mini Tamiya Connector to make it compatible with a huge range of Airsoft Guns. If you need a compact 7.4v LiPo for a Specna Arms PDW or other Airsoft Gun with a tight battery space, then this is the ideal choice.

A compact LiPo Airsoft Battery, designed to be used in tight awkward spaces, without compromising on overall capacity. It comes supplied with the more efficient Deans connector already installed.

A spare or replacement NiMH Battery for Airsoft Electric Pistols, such as the CYMA CM and Tokyo Marui series, perfect for staying in the fight for longer. If you want to play for longer during an Airsoft Game without having to return to the safe zone, then stock up on spare batteries today.

A compact block style battery from GFC Energy. The battery is comprised of 8 1.2V cells, providing 9.6V total voltage. This battery is ideally shaped for use inside an AR36 polymer handguard, a solid stock battery compartment in an SMG5, or a vertical grip battery box. This battery is wired to a mini-Tamiya connector, and can also be used for RC vehicles or other electronics hobbies.

This LiPo battery from Gens Ace is designed to fit into compact and slim battery compartments, such as the M4/AR15 buffer tube and the AK47/74 top cover. The battery connects to your AEG via a mini-Tamiya connector and provides 1000mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8.5cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

A large stick type battery, designed to output a high power for fast trigger response and rate of fire for up to three quarters of a day on a slow charge.

If you need spare batteries for your AEP with a bit more oomph than the standard NiMh, this will do it! The IPower 7.4v 680mAh 20c LiPo Micro Battery is designed for CYMA CM.1xx series AEPs, fitted with a standard AEP connector and sized to fit AEP battery compartments. This battery is NOT compatible with AEP SMGs like the VZ61, MAC-10 or SMG-7 or the MOSFET-equipped CM.1xxS series.

This battery can be charged via its balance port using a LiPo balance charger, and as always, we recommend never leaving a LiPo on charge unattended and always using a LiPo charging bag.