RIS/RAS Rail & Attachments

This lens protector is a must-have product for any Airsoft Skirmisher who intends to play in a CQB environment, protecting your sights and scopes from being shot out by stray BB. Guess what's cheaper: A new sight or lens protector? 

Ships with peel-off protective film so it arrives perfectly clear when you attach it to your RIF

A low profile ergonomic & stippled grip constructed from Polymer for attaching to Airsoft 20mm RIS rail systems.

A Polymer constructed Angled Foregrip for 20mm Rail Systems, which provides a comfortable point to achieve a strong grip over your Airsoft Gun.

A Polymer constructed Angled Foregrip for 20mm Rail Systems, which provides a comfortable point to achieve a strong grip over your Airsoft Gun.

A perfect grip for people with all sized hands. Secures in no time with only one bolt to care about.

A perfect grip for people with all sized hands. Secures in no time with only one bolt to care about.

If you prefer the tried and tested vertical foregrip over other gripping options but want something a little more modern than the average VFG, the Specna Arms Angled Vertical Foregrip may be just what you have been looking for! This grip can be attached to any 20mm Picatinny rail surface and features a slightly swept-back angle, intended to encourage a more comfortable wrist position whilst still making use of the advantages of a traditional vertical foregrip.

A Polymer constructed Foregrip for 20mm Rails, which will easily attach to your Replica and provide a stable position to brace your gun against the shoulder, and achieve a steady and consistent aim. It could also reduce fatigue experienced during a skirmish from an incorrect hand position. The low-profile nature of this grip reduces the likelihood of snagging on your own kit/equipment during the day.

A Polymer constructed Foregrip for 20mm Rails, which will easily attach to your Replica and provide a stable position to brace your gun against the shoulder, and achieve a steady and consistent aim. It could also reduce fatigue experienced during a skirmish from an incorrect hand position. The low-profile nature of this grip reduces the likelihood of snagging on your own kit/equipment during the day.

A very easy to use fore grip that can be locked in a compact or full vertical position depending on your situation and requirements. 

This High Profile Rail Riser is designed for any 20mm RIS/RAS Accessory, and is designed to lift it up off the Rail. This is particularly useful for those trying to use a Lower Face Mask with a Red Dot Sight, as you might find that you Mask stops you from aiming down your standard Rail System.

Built from lightweight polymer, these rail panels are designed to cover 20mm RIS / RAS rails and offer a more comfortable grip on your RIF.

Built from lightweight polymer, these rail panels are designed to cover 20mm RIS / RAS rails and offer a more comfortable grip on your RIF.

A transparent Polymer lens protector designed for EOTech Style Sights, protecting your Sight from BB's and other projectiles designed as a first defence, protecting your lens.

Designed to be fit to Airsoft Rifles Rails in front of expensive Sights and Scopes to deflect incoming BBs to prevent the Sights becoming damaged. 

An ergonomically designed 20mm RIS foregrip, created to promote a comfortable and natural grip on their Airsoft gun. Constructed from high quality polymer with a slightly textured surface.  

A Vertial Foregrip designed to give the user an extra control point on their weapon. The foregrip is constructed from Polymer and is designed to fit 20mm RIS / RAS Rails. 

A Vertial Foregrip designed to give the user an extra control point on their weapon. The foregrip is constructed from Polymer and is designed to fit 20mm RIS / RAS Rails. 

A replacement dust cover for the top of CYMA CM.040 AK47 Variant Rifles, designed to add a top 20mm RIS / RAS Rail for the attachment of Sights and Scopes without the use of a Side Scope Mount. 

A mock PEQ Box, designed to hold PEQ size Airsoft batteries, but can be extended with the use of an included extension module for larger batteries.

MGP brings us a high quality Quick Detach (QD) sling adaptor, allowing you to connect your weapon of choice to a sling. The QD system is locked in place by 4 steel ball bearings which are lowered with a push of the centre button to lock in place and release, again by pressing down the same button.

This version supports 20mm RIS / RAS rail system. Simply loosely screw the fixtures together using the Allen key included, then slide them onto your RIS rail, then tighten to lock the fixture in place and voila! Now you can attach and detach your sling swivel with ease, allowing for a dynamic and efficient playstyle on the battlefield.

No more unslinging your rifle from your back or shoulders!

Add a foregrip your rifle for maximum control. The grip is secured tightly onto rails by first sliding it on then screwing the bottom until it is locked in place. The grip can be placed anywhere up and down a Quad Rail, and is designed to allow the user to chose where the additional control point on their weapon is placed. The further forward the grip is placed the slower the barrel will turn, and the further back the grip is placed the faster the barrel will turn. This is the perfect purchase for those Airsofters who want to add a bit of flair to their weapon, or want a grip on the front of their weapon.

A Vertical Foregrip designed to be attached onto the Front Handguard of Rifles and Submachine Guns to give the user a more stable grip on the weapon. 

A robust and adjustable bi-pod designed for use with Airsoft Sniper Rifles, supplied with a 20mm RIS rail adaptor allowing the bi-pod to be used with the widest possible range of sniper rifles.

A simple and easy-to-use Vertical Foregrip for Airsoft Replicas, compatible with 20mm RIS/RAS (Picatinny Rail Systems). To install the Grip, simply unscrew the base of the Grip and slide it over the 20mm Rail. Tightening the base of the Grip will raise the middle section of the Grip and lock it into a Rail Slot (if you've aligned it correctly). This will give you a comfortable platform to grip and brace your Airsoft Gun, making for steadier and more viable aiming, even in the heat of the moment.

If you are looking for a grip that also converts into a bipod but looking for weight and solid construction then this is for you. 

A 20mm Railed MK18 Handguard for AR Platform AEGs and GBB replicas, which is ideal for those searching for the 'Special Forces' look. It is constructed to a lovely standard from Aluminium and features Numbered Rail Slots for the precise placement of accessories. The bottom Rail measures a total of 21.3cm, and the other three at 24.4cm. If you're looking to spice up your AR with some external furniture, then a Handguard swap is a great place to start.

One of the few problems with old-school cool like the SMG5 series of AEGs is that you are rather limited in rail mounting space, meaning your mission essential equipment that makes you a true operator has to be left behind. Ask the US Navy SEALs, they are known to use pipe clips and zip ties to attach rails to their MP5SD6s. You no longer have to resort to this pure bodgery, with the Extended top rail mount from CYMA you now have a Picatinny scope mount with forward M-LOK sections for tactical weapon lights, lasers, battery boxes, or anything else you need. This is all kept at the 12 o'clock position, keeping your ambi friendly SMG just that. 

If you are an AK fan but are getting green-eyed over the M4/AR-15's accessory options, a railed handguard will cure that! The CYMA 20mm Picatinny Railed Handguard for AK AEG is constructed from solid high density polymer and provides 20mm Picatinny rails at the 3, 6, 9 and 12 o'clock positions, ready for 20mm Picatinny accessories.

The side rails are short lengths, ideally designed to mount a tactical flashlight or aiming laser but can also be removed if you prefer slick sides on your handguard. The top rail features 12cm of rail space, allowing for a forward mounted red dot sight to be fitted for that slick PMC look. The bottom rail is 11cm long, providing enough room at the front so you can add a vertical or angled foregrip, or even a bipod if you see fit. The sides of the lower handguard also include ribs for extra grip, similarly to the standard issue AK-10x polymer handguards. If you want to mount your mission essential kit to your AK AEG or GBBR this handguard is one of the cheapest ways to do it!

A tactical folding Vertical Foregrip, designed for use with Airsoft AEG and GBB rifles, which allows the user to flip it down when required and fold back up when not in use to give it a lower profile.