EU Warehouse Stock

If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Gen's Ace 7.4v 1500mAh 25C LiPo Stick Battery measures approximately 12x1.5x1.6cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Mini-Tamiya connector and the length of wire between the cell group and the connector is approximately 6cm.

The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!

If you are looking to further extend your advantage and push your TM NGRS system to the limits reinforced gears are a must for long term reliability under increased stress. The Laylax EG Hard Gear Set is specifically designed for the Tokyo Marui Next Generation Recoil Shock (NGRS) gearbox and includes a hardened steel spur gear, sector gear and bevel gear. This gearset is a standard ratio set (18:1), intended to provide a great compromise between high speed and high torque, allowing you to take your build in either direction and still benefit from reinforced gears!

If you have been looking for an affordable sidearm or base gun for your next build, the Golden Eagle Hi-capa 4.3 GBB is a fantastic choice. This Hi-capa boasts full metal construction, full Tokyo Marui compatibility and a price that is hard to believe!

Though it is based on the Tokyo Marui 4.3, the Golden Eagle Hi-capa has a 6.02mm tightbore inner barrel, adding to its accuracy potential, improving gas efficiency and raising FPS slightly. Golden Eagle also saw fit to add an 11mm CW female threaded outer barrel, meaning you don't need a new outer barrel to fit a tracer or suppressor, just an 11mm CW to 14mm CCW adapter. Unlike many other cheap GBB pistols, the Golden Eagle Hi-capa feels buttery smooth when cycling and is remarkably consistent, pointing to well-made internals and tight tolerances.

Whether you are building it out for speedsoft use or you want a cheap, full metal holster filler, the Golden Eagle Hi-capa is a great value and a great performer!

For all you serious MP5 operators, 8Fields has got you covered with their Quad magazine insert, holding up to 4 mag for some serious round capacity.

This elastic insert gives you quick and easy access to all your magazines with perfect retention. With front and back Velcro, it gives you the flexibility to attach it wherever you please as long as its Velcro including kangaroo pouches of a lot of plate carriers.

Able to be fastened in placed securely with a full Velcro backing, the 8Fields Rigid Combat Belt is a tough and sturdy addition to any operator's loadout.

If your CM.041 SMG-5 has a loose or rattly charging handle, this might solve it! The CYMA Charging Handle Spring Catch for SMG-5 is a replacement original part for the CM.041 series and will work on the -SD models but not the -K. This part braces the spring inside the receiver and keeps your charging handle tight and in place. If you pull your charging handle back and there is no spring tension and the handle loosely wanders around in the cocking tube, you probably need a new one of these!

Pistol mag retention or rifle mag retention? This pouch offers the best of both worlds.

The two stacked pockets in a low profile design, held together with adjustable elastic bungee retention cord, you can be sure that both your main and sidearm mags are kept safe and secure and to hand for quick reloads all in place!

The magazine pocket is designed for STANAG type mags in mind with the front most pistol pockets able to fit a whole range of pistol magazines such as EU17 or 1911 systems.

Mounted by MOLLE retention straps, this pouch is for those of you that like to keep things compact and efficient, with  for those speedy reloads in the heat of battle.

If you need a replacement bolt handle for your CM.707 Sniper rifle you are in luck! This CYMA part is an original replacement, intended for the refurbishment of an old and worn out sniper rifle. The handle is constructed from steel and does not include the polymer end piece so you will need the original end piece from your rifle to complete it.

If you are tuning your gearbox for a high rate of fire build a reinforced tappet plate is a must for your shopping list. The Perfect Tappet Plate from Laylax replaces your original tappet plate to keep your Tokyo Marui NGRS AEG running for longer at high speed thanks to its reinforced polymer construction.

If you are looking for an excellent replacement piston for your AEG then look no further! The RetroArms 14.5 Steel Tooth Piston is the perfect piston upgrade. Its injection moulded carbon-reinforced polymer ensures premium quality and consistency, the fourteen-and-a-half steel teeth are highly wear-resistant and greatly extend the lifespan, and it also keeps your Airsoft rifle performing up to standards. The half-tooth allows the piston to be picked up by the gears more easily and minimises the chance of the teeth bouncing off the gear and causing internal damage.

The RetroArms 14.5 Steel Tooth Piston is great for high-performance builds and is designed for version 2 and version 3 gearboxes. Make your AEG premium with this simple upgrade piece!

A high quality 11.1V LiPo battery with a 1200mAh capacity, suitable for both Airsoft and RC use.

This LiPo battery from Gens Ace is designed to fit into flat and long battery compartments, such as those found inside the handguards of an AR36 or SMG-5. The battery connects to your AEG via a Deans connector (aka a T-Plug) and provides 1300mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

The Stainless Steel Cylinder for CM.706 series comes as a set with a pre-installed brass cylinder head and is a replacement original part manufactured by CYMA themselves. This can be a handy part to have if you use your CM.706 at different sites with different FPS limits, as you can make a second cylinder and swap them out as and when you need (though this does require disassembly). The set includes both the cylinder and the cylinder head.

If you're looking for a compact red dot sight, but want something that looks a bit different to the norm, the Miniature Rifle reflex sight from Big Dragon could be what you need! The Miniature Rifle Reflex sports a crisp, fine 2 MOA dot with 6 levels of brightness adjustment for aiming, and comes with both a low and high mount for 20mm Picatinny rails. 

Where my milsim bois at? The East Crane EC-202 M-417 DMR is the marksman rifle you have been looking for, whether you run a UKSF, Delta or any other SF loadout! Boasting full metal construction, a quick change spring system and a programmable MOSFET capable of semi-automatic only, the EC-202 is ready for whatever role you place it in, but we think it would make a beast of a DMR!

With a 6.04mm Tightbore inner barrel, rotary HOP-up unit, version 2.5/version 2 long gearbox and CHONKY 7.62x51mm style magazines, the EC-202 is kitted out for long range skirmishing, whether you push it up to DMR limits or not. On the outside, we have more 20mm Picatinny rails than we will ever need, a 14mm CCW male threaded barrel, ready for a suppressor or tracer and a snag-reducing low-profile stock with full adjustability for ease of movement. Wack a big scope on this bad boy and get to work!

If you're looking for some quick simulated medical action. This tourniquet holder, attaches via Velcro and can be installed either vertically or horizontally for quick access to plate carriers and chest rigs. This could mean the difference between (simulated) life and death!

A shell for gearbox type V2 with reinforced aluminium construction. The front part has been strengthened with the most exposed area being considerably thickened and the area of the contact with the cylinder has been improved so as to evenly transfer the loads.

The shell is mounted using its 8mm bearings. This gearbox shell is designed for use in J.G replicas but should potentially work in replicas of other makes and manufacturers.

If you are looking for a helmet but want to remain light on your feet, the FMA FAST BJ Helmet Replica is definitely worth a look. This helmet is styled after the Base Jump/Bump FAST helmet and features a built-in NVG mount at the front, ARC rails on either side and a ported shell to improve airflow and comfort along with reducing the chances of goggles fogging. 

Also featured in this helmet is the game-changing OCC adjustment dial, designed to keep the helmet super snug and stable on your head no matter what you have mounted or how hard you sprint. If you're planning on running a GoPro or other action camera to record your Airsoft escapades, this is one of the most stable platforms you can mount it to!

If you are after a large rifle scope for your DMR or Sniper rifle, the PCS 3-9X40E Illuminated Rifle Scope should fit the role! With full tool-less adjustment for windage and elevation and a crisp Mil-dot reticle that can be illuminated red, or green with 5 levels of brightness to choose from, the 3-9X40E is a highly effective yet affordable optical sight. As a bonus, this scope comes complete and ready to mount with 1-inch scope rings for 20mm Picatinny rails, leaving you nothing left to buy but the rifle!

A complete set inspired by a famous real-world Gen.3 combat uniform, the Primal Gear G3 uniform includes a UBACS style combat shirt, combat trousers and knee pads with an expansive range of flat colours and some rare camouflage colour options to choose from!

The body of the shirt is 100% sweat-wicking cotton, intended to help you stay cool while wearing body armour or a plate carrier, and each sleeve features a velcro-secured admin pocket with additional velcro on the outside for I.D or morale patches. On each sleeve, the Combat Shirt is equipped with elbow pad pockets so you can add elbow pads to keep you protected when crawling. The collar is equipped with a YKK® branded zip, so you have the choice of zipping up to protect your throat or unzipping for improved airflow and cooling.

The combat trousers along with the sleeves and collar of the shirt are constructed from a 65% polyester 35% cotton mix with a ripstop weave design, ensuring mid-skirmish snags don't result in damage. The design of the trousers is adorned with considerately designed pockets with placement developed following feedback from special forces operators using the G2 uniform in the field. On each leg, we have a large cargo pocket, a thigh pocket, the usual angled trouser pocket and a lower leg pocket. The ride height of the knee pads can also be adjusted via bungee cord concealed inside the thigh pockets, meaning you will never feel the pain of kneeling on a thorn in the woods or a BB in CQB. Trust us, it hurts! 

Sizing information can be found in the "Full Description" so make sure you measure up for a perfect fit. One of the best things about Primal Gear's G3 uniform is its availability in rare camouflage and flat colour options not often replicated by other brands. These include Wz.93 Polish Woodland and ATACS FG, both hard-to-find patterns in the modern age of multicam!