LiPo Batteries

A LiPo Crane Stock battery designed to fit in stocks and small spaces which other large batteries do not fit. The battery is also know as a Nunchuck battery, with the cells connected via the wires allowing them to be placed down the side of barrels or in an M4 Crane Stock.

A ultra thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c, giving it a 20w output.

A Standard powered Airsoft Battery, designed to be used in almost all Airsoft AEG weapons with a mini-Tamiya connector, providing the perfect amount of power for most Airsoft Weapons. 

A stick 7.4v 1100mAh LiPo designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries, intended to allow Airsofters to get the best possible performance from their Airsoft Electric Guns.

VP Racing are well known for their high quality and high performance batteries with this one being a crane form factor. The battery has a voltage of 7.4v, has a capacity of 1450mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery consists of two cells working in tandem, with each cell measuring 13x0.7x2cm each with a cable length of roughly 7.5cm of wire. The battery should fit in crane stock battery compartments such as M4s and some handguards and full stocks, but remember to measure up before hand!

An ultra thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c, giving it a 20w output. 

If you are heavy on the trigger with your LiPo ready AEP you might need a couple of these! The IPower 7.4V 680mAh 20c LiPo battery is just like a normal LiPo stick, but much much smaller. This battery is designed as a spare battery for the CYMA CM.xxxS series of LiPo-ready AEPs and is pre-wired to a mini-Deans connector. This battery can be charged like a normal LiPo battery; using the balance lead and with a LiPo balance charger. This battery cannot be charged with a normal NiMh/NiCad charger, do not attempt it as you may cause a fire. If you are the creative type this battery's minuscule form could lend itself well to an electronics project or R/C use.

If you need spare batteries for your AEP with a bit more oomph than the standard NiMh, this will do it! The IPower 7.4v 680mAh 20c LiPo Micro Battery is designed for CYMA CM.1xx series AEPs, fitted with a standard AEP connector and sized to fit AEP battery compartments. This battery is NOT compatible with AEP SMGs like the VZ61, MAC-10 or SMG-7 or the MOSFET-equipped CM.1xxS series. 

This battery can be charged via its balance port using a LiPo balance charger, and as always, we recommend never leaving a LiPo on charge unattended and always using a LiPo charging bag.

If you need a battery for your M4/AR-15 buffer tube or your top-wired AK AEG this should be perfect! The VAPEX 7.4v 1300mAh 20C LiPo Stick Battery measures 14 x 1.2 x 1.8cm approximately with a wire length of 9cm, making it a good fit in rear wired M4s with a buffer tube battery compartment, SMG-5K AEGs or AK AEGs in the top-wired configuration.

The pre-installed battery connector is the common mini-Tamiya type and the battery has a discharge rate of 20C, making it ideal for Airsoft applications but also useful for those needing a compact power source for electronics or R/C projects.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. Fitted with a deans connector for low resistance.

A 7.4v 1500mAh LiPo battery that provides a 20c discharge rate and is highly compact, making it ideal for external PEQ battery boxes and tight, square spaces.

Suitable not only for Airsoft but for RC vehicles and toys too, this  7.4v 2200mAh LiPo Stick Battery will fit in tight areas like stock tubes and handguards where other batteries would normally not.

A stick battery designed for most M4 stock tubes, solid stock sand some hand guards. An ideal starter LiPo which you should get half a days use out of at least from a slow charge.

VAPEX are well known for their high quality and high performance batteries with this one being a block form factor. The battery has a voltage of 7.4v, has a capacity of 1300mAh and a discharge rate of 30C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery's dimensions are 10x1.2x3cm with a cable length of roughly 10cm. This battery should fit AEGs with larger battery compartments such as full stock AKs and M16s, within the handguard of AR36s and front wired MP5s.

An ultra thin, long LiPo crane stock battery. The battery is designed to fit into as little space as possible, taking up very little room allowing it to be fit into stocks and small battery compartments.

A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.

A 7.4v 1450mAh LiPo stick battery suitable not only for Airsoft but for RC vehicles and toys too.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. 

A LiPo crane stock battery designed to fit in stocks and small spaces which other large batteries do not fit.

An ultra thin and lightweight crane stock battery, perfect for squeezing into the ever more popular Airsoft crane stock.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

A LiPo crane stock battery designed to fit in crane and solid stocks, where other batteries would be wasting the available space. 

A high quality and ultra compact 7.4v Lithium Polymer Battery with 850mAh of capacity, wth a 30C discharge rating.

This LiPo battery from Gens Ace is designed to fit into compact and slim battery compartments, such as the M4/AR15 buffer tube and the AK47/74 top cover. The battery connects to your AEG via a mini-Tamiya connector and provides 1000mAh capacity with a 25C discharge rating. The battery is coated with heat shrink to prevent abrasion damage to the cells, and has a wire length of approximately 8.5cm, allowing some flexibility when squeezing the battery into small spaces. This battery would be great for any Airsoft gun which requires a 7.4V LiPo, but would also be of use for R/C vehicles, Drones or other electronics hobbies.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A 7.4v 1000mAh single stick battery that is ideal for squeezing in small compartments where space is a premium, particularly M4/15/16 stock tubes and those rear wired weapons with small battery spaces.

A LiPo stick battery designed to fit in handguards in replacement of the traditional 1600mAh NiMH blocks (G36 handguards etc). 

If you need a slim stick battery for your ASG Scorpion, M4/AR-15 AEG buffer tube or top-wired AK AEG this will do the trick! The Gen's Ace 7.4v 1200mAh 25C LiPo Stick Battery measures approximately 13x1x2cm which makes it perfect for rear wired M4 platforms with the standard buffer tube battery compartment, top wired AKs which house their battery beneath the top cover and SMG-5K platforms. The battery is pre-wired to a Deans connector and the length of wire between the cell group and the connector is approximately 6cm.

The battery is a 7.4V 2-cell battery in stick configuration with a continuous discharge rate of 25C, making it great for almost any Airsoft AEG and a perfect fit for the ASG Scorpion EVO 3A1, though make sure you measure before ordering!

A 7.4v Lithium Polymer Battery designed for use in battery compartments with limited space for a thin, but long battery.

If you need a compact 7.4V LiPo for your buffer tube, PDW stock or other cramped battery compartment, the VP Racing 7.4V 800mAh 20c LiPo Stick Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and measures 10.2 x 1.1 x 1.9 cm with 5cm of wire length, making it suitable for most Airsoft AEGs, even those with small battery compartments. As always, we recommend measuring thoroughly to ensure it fits before ordering!